From: Thierry Reding <treding@xxxxxxxxxx>
Convert the NVIDIA Tegra186 (and later) PMC bindings from the free-form
text format to json-schema.
Signed-off-by: Thierry Reding <treding@xxxxxxxxxx>
---
.../arm/tegra/nvidia,tegra186-pmc.txt | 133 ------------
.../arm/tegra/nvidia,tegra186-pmc.yaml | 199 ++++++++++++++++++
2 files changed, 199 insertions(+), 133 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
create mode 100644 Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.yaml
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
deleted file mode 100644
index 576462fae27f..000000000000
--- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
+++ /dev/null
@@ -1,133 +0,0 @@
-NVIDIA Tegra Power Management Controller (PMC)
-
-Required properties:
-- compatible: Should contain one of the following:
- - "nvidia,tegra186-pmc": for Tegra186
- - "nvidia,tegra194-pmc": for Tegra194
- - "nvidia,tegra234-pmc": for Tegra234
-- reg: Must contain an (offset, length) pair of the register set for each
- entry in reg-names.
-- reg-names: Must include the following entries:
- - "pmc"
- - "wake"
- - "aotag"
- - "scratch"
- - "misc" (Only for Tegra194 and later)
-
-Optional properties:
-- nvidia,invert-interrupt: If present, inverts the PMU interrupt signal.
-- interrupt-controller: Identifies the node as an interrupt controller.
-- #interrupt-cells: Specifies the number of cells needed to encode an
- interrupt source. The value must be 2.
-
-Example:
-
-SoC DTSI:
-
- pmc@c3600000 {
- compatible = "nvidia,tegra186-pmc";
- reg = <0 0x0c360000 0 0x10000>,
- <0 0x0c370000 0 0x10000>,
- <0 0x0c380000 0 0x10000>,
- <0 0x0c390000 0 0x10000>;
- reg-names = "pmc", "wake", "aotag", "scratch";
- };
-
-Board DTS:
-
- pmc@c360000 {
- nvidia,invert-interrupt;
- };
-
-== Pad Control ==
-
-On Tegra SoCs a pad is a set of pins which are configured as a group.
-The pin grouping is a fixed attribute of the hardware. The PMC can be
-used to set pad power state and signaling voltage. A pad can be either
-in active or power down mode. The support for power state and signaling
-voltage configuration varies depending on the pad in question. 3.3 V and
-1.8 V signaling voltages are supported on pins where software
-controllable signaling voltage switching is available.
-
-Pad configurations are described with pin configuration nodes which
-are placed under the pmc node and they are referred to by the pinctrl
-client properties. For more information see
-Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
-
-The following pads are present on Tegra186:
-csia csib dsi mipi-bias
-pex-clk-bias pex-clk3 pex-clk2 pex-clk1
-usb0 usb1 usb2 usb-bias
-uart audio hsic dbg
-hdmi-dp0 hdmi-dp1 pex-cntrl sdmmc2-hv
-sdmmc4 cam dsib dsic
-dsid csic csid csie
-dsif spi ufs dmic-hv
-edp sdmmc1-hv sdmmc3-hv conn
-audio-hv ao-hv
-
-Required pin configuration properties:
- - pins: A list of strings, each of which contains the name of a pad
- to be configured.
-
-Optional pin configuration properties:
- - low-power-enable: Configure the pad into power down mode
- - low-power-disable: Configure the pad into active mode
- - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
- TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
- The values are defined in
- include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
-
-Note: The power state can be configured on all of the above pads except
- for ao-hv. Following pads have software configurable signaling
- voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv,
- ao-hv.
-
-Pad configuration state example:
- pmc: pmc@7000e400 {
- compatible = "nvidia,tegra186-pmc";
- reg = <0 0x0c360000 0 0x10000>,
- <0 0x0c370000 0 0x10000>,
- <0 0x0c380000 0 0x10000>,
- <0 0x0c390000 0 0x10000>;
- reg-names = "pmc", "wake", "aotag", "scratch";
-
- ...
-
- sdmmc1_3v3: sdmmc1-3v3 {
- pins = "sdmmc1-hv";
- power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
- };
-
- sdmmc1_1v8: sdmmc1-1v8 {
- pins = "sdmmc1-hv";
- power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
- };
-
- hdmi_off: hdmi-off {
- pins = "hdmi";
- low-power-enable;
- }
-
- hdmi_on: hdmi-on {
- pins = "hdmi";
- low-power-disable;
- }
- };
-
-Pinctrl client example:
- sdmmc1: sdhci@3400000 {
- ...
- pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
- pinctrl-0 = <&sdmmc1_3v3>;
- pinctrl-1 = <&sdmmc1_1v8>;
- };
-
- ...
-
- sor0: sor@15540000 {
- ...
- pinctrl-0 = <&hdmi_off>;
- pinctrl-1 = <&hdmi_on>;
- pinctrl-names = "hdmi-on", "hdmi-off";
- };
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.yaml b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.yaml
new file mode 100644
index 000000000000..6946df96ec81
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.yaml
@@ -0,0 +1,199 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/tegra/nvidia,tegra186-pmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra Power Management Controller (PMC)
+
+maintainers:
+ - Thierry Reding <thierry.reding@xxxxxxxxx>
+ - Jon Hunter <jonathanh@xxxxxxxxxx>
+
+properties:
+ compatible:
+ enum:
+ - nvidia,tegra186-pmc
+ - nvidia,tegra194-pmc
+ - nvidia,tegra234-pmc
+
+ reg:
+ minItems: 4
+ maxItems: 5
+
+ reg-names:
+ minItems: 4
+ maxItems: 5
+ items:
+ - const: pmc
+ - const: wake
+ - const: aotag
+ - const: scratch
+ - const: misc
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ description: Specifies the number of cells needed to encode an
+ interrupt source. The value must be 2.
+ const: 2
+
+ nvidia,invert-interrupt:
+ description: If present, inverts the PMU interrupt signal.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+if:
+ properties:
+ compatible:
+ contains:
+ const: nvidia,tegra186-pmc
+then:
+ properties:
+ reg:
+ maxItems: 4
+
+ reg-names:
+ maxItems: 4
+else:
+ properties:
+ reg:
+ minItems: 5
+
+ reg-names:
+ minItems: 5
+
+patternProperties:
+ "^[a-z0-9]+-[a-z0-9]+$":
+ if:
+ type: object
+ then:
+ description: |
+ These are pad configuration nodes. On Tegra SoCs a pad is a set of
+ pins which are configured as a group. The pin grouping is a fixed
+ attribute of the hardware. The PMC can be used to set pad power
+ state and signaling voltage. A pad can be either in active or
+ power down mode. The support for power state and signaling voltage
+ configuration varies depending on the pad in question. 3.3 V and
+ 1.8 V signaling voltages are supported on pins where software
+ controllable signaling voltage switching is available.
+
+ Pad configurations are described with pin configuration nodes
+ which are placed under the pmc node and they are referred to by
+ the pinctrl client properties. For more information see
+
+ Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+ The following pads are present on Tegra186:
+
+ csia, csib, dsi, mipi-bias, pex-clk-bias, pex-clk3, pex-clk2,
+ pex-clk1, usb0, usb1, usb2, usb-bias, uart, audio, hsic, dbg,
+ hdmi-dp0, hdmi-dp1, pex-cntrl, sdmmc2-hv, sdmmc4, cam, dsib,
+ dsic, dsid, csic, csid, csie, dsif, spi, ufs, dmic-hv, edp,
+ sdmmc1-hv, sdmmc3-hv, conn, audio-hv, ao-hv
+
+ The following pads are present on Tegra194:
+
+ csia, csib, mipi-bias, pex-clk-bias, pex-clk3, pex-clk2,
+ pex-clk1, eqos, pex-clk-2-bias, pex-clk-2, dap3, dap5, uart,
+ pwr-ctl, soc-gpio53, audio, gp-pwm2, gp-pwm3, soc-gpio12,
+ soc-gpio13, soc-gpio10, uart4, uart5, dbg, hdmi-dp3, hdmi-dp2,
+ hdmi-dp0, hdmi-dp1, pex-cntrl, pex-ctl2, pex-l0-rst,
+ pex-l1-rst, sdmmc4, pex-l5-rst, cam, csic, csid, csie, csif,
+ spi, ufs, csig, csih, edp, sdmmc1-hv, sdmmc3-hv, conn,
+ audio-hv, ao-hv
+
+ properties:
+ pins:
+ $ref: /schemas/types.yaml#/definitions/string
+ description: Must contain the name of the pad(s) to be
+ configured.
+
+ low-power-enable:
+ description: Configure the pad into power down mode.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ low-power-disable:
+ description: Configure the pad into active mode.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ power-source:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
+ TEGRA_IO_PAD_VOLTAGE_3V3 to select between signalling
+ voltages.
+
+ The values are defined in
+
+ include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h
+
+ The power state can be configured on all of the above pads
+ except for ao-hv. Following pads have software configurable
+ signaling voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv,
+ audio-hv, ao-hv.
+
+ phandle: true
+
+ required:
+ - pins
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - reg-names
+
+additionalProperties: false
+
+dependencies:
+ interrupt-controller: ['#interrupt-cells']
+ "#interrupt-cells":
+ required:
+ - interrupt-controller
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra186-clock.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/pinctrl/pinctrl-tegra-io-pad.h>
+ #include <dt-bindings/memory/tegra186-mc.h>
+ #include <dt-bindings/reset/tegra186-reset.h>
+
+ pmc@c3600000 {
+ compatible = "nvidia,tegra186-pmc";
+ reg = <0x0c360000 0x10000>,
+ <0x0c370000 0x10000>,
+ <0x0c380000 0x10000>,
+ <0x0c390000 0x10000>;
+ reg-names = "pmc", "wake", "aotag", "scratch";
+ nvidia,invert-interrupt;
+
+ sdmmc1_3v3: sdmmc1-3v3 {
+ pins = "sdmmc1-hv";
+ power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+ };
+
+ sdmmc1_1v8: sdmmc1-1v8 {
+ pins = "sdmmc1-hv";
+ power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+ };
+ };
+
+ sdmmc1: mmc@3400000 {
+ compatible = "nvidia,tegra186-sdhci";
+ reg = <0x03400000 0x10000>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bpmp TEGRA186_CLK_SDMMC1>,
+ <&bpmp TEGRA186_CLK_SDMMC_LEGACY_TM>;
+ clock-names = "sdhci", "tmclk";
+ resets = <&bpmp TEGRA186_RESET_SDMMC1>;
+ reset-names = "sdhci";
+ interconnects = <&mc TEGRA186_MEMORY_CLIENT_SDMMCRA &emc>,
+ <&mc TEGRA186_MEMORY_CLIENT_SDMMCWA &emc>;
+ interconnect-names = "dma-mem", "write";
+ iommus = <&smmu TEGRA186_SID_SDMMC1>;
+ pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+ pinctrl-0 = <&sdmmc1_3v3>;
+ pinctrl-1 = <&sdmmc1_1v8>;
+ };
--
2.33.1
