RE: [PATCH 2/2] net: ethernet: Add driver for Sunplus SP7021

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



> 
> Hi--
> 
> On 11/3/21 4:02 AM, Wells Lu wrote:
> > diff --git a/drivers/net/ethernet/sunplus/Kconfig
> > b/drivers/net/ethernet/sunplus/Kconfig
> > new file mode 100644
> > index 0000000..a9e3a4c
> > --- /dev/null
> > +++ b/drivers/net/ethernet/sunplus/Kconfig
> > @@ -0,0 +1,20 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +#
> > +# Sunplus Ethernet device configuration #
> > +
> > +config NET_VENDOR_SUNPLUS
> > +	tristate "Sunplus Dual 10M/100M Ethernet (with L2 switch) devices"
> > +	depends on ETHERNET && SOC_SP7021
> > +	select PHYLIB
> > +	select PINCTRL_SPPCTL
> > +	select COMMON_CLK_SP7021
> > +	select RESET_SUNPLUS
> > +	select NVMEM_SUNPLUS_OCOTP
> > +	help
> > +	  If you have Sunplus dual 10M/100M Ethernet (with L2 switch)
> > +	  devices, say Y.
> > +	  The network device supports dual 10M/100M Ethernet interfaces,
> > +	  or one 10/100M Ethernet interface with two LAN ports.
> > +	  To compile this driver as a module, choose M here.  The module
> > +	  will be called sp_l2sw.
> 
> Please use NET_VENDOR_SUNPLUS in the same way that other
> NET_VENDOR_wyxz kconfig symbols are used. It should just enable or
> disable any specific device drivers under it.
> 
> 
> --
> ~Randy

I looked up Kconfig file of other vendors, but not sure what I should do.
Do I need to modify Kconfig file in the form as shown below?

# SPDX-License-Identifier: GPL-2.0
#
# Sunplus device configuration
#

config NET_VENDOR_SUNPLUS
	bool "Sunplus devices"
	default y
	depends on ARCH_SUNPLUS
	---help---
	  If you have a network (Ethernet) card belonging to this
	  class, say Y here.

	  Note that the answer to this question doesn't directly
	  affect the kernel: saying N will just cause the configurator
	  to skip all the questions about Sunplus cards. If you say Y,
	  you will be asked for your specific card in the following
	  questions.

if NET_VENDOR_SUNPLUS

config SP7021_EMAC
	tristate "Sunplus Dual 10M/100M Ethernet (with L2 switch) devices"
	depends on ETHERNET && SOC_SP7021
	select PHYLIB
	select PINCTRL_SPPCTL
	select COMMON_CLK_SP7021
	select RESET_SUNPLUS
	select NVMEM_SUNPLUS_OCOTP
	help
	  If you have Sunplus dual 10M/100M Ethernet (with L2 switch)
	  devices, say Y.
	  The network device supports dual 10M/100M Ethernet interfaces,
	  or one 10/100M Ethernet interface with two LAN ports.
	  To compile this driver as a module, choose M here.  The module
	  will be called sp_l2sw.

endif # NET_VENDOR_SUNPLUS

Best regards,
Wells




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux