Example: In the setup that we tested the driver, we had a clock chip that was hardware-routed only to the positive side of the local oscillator input (LOP pin) from admv1013. Therefore, I think keeping the property in the DT might be useful. Regards, -- Antoniu Miclăuş > -----Original Message----- > From: Miclaus, Antoniu > Sent: Wednesday, November 3, 2021 10:09 AM > To: Rob Herring <robh@xxxxxxxxxx> > Cc: jic23@xxxxxxxxxx; linux-iio@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; > linux-kernel@xxxxxxxxxxxxxxx; Sa, Nuno <Nuno.Sa@xxxxxxxxxx> > Subject: RE: [PATCH v3 2/2] dt-bindings: iio: frequency: add admv1013 doc > > Hello Rob, > > These properties are fixed and available in the datasheet (binary format): > https://www.analog.com/media/en/technical-documentation/data- > sheets/ADMV1013.pdf > > Please see Page 37 of 39, Table 15, QUAD_SE_MODE. > > Regards, > -- > Antoniu Miclăuş > > > -----Original Message----- > > From: Rob Herring <robh@xxxxxxxxxx> > > Sent: Tuesday, November 2, 2021 7:51 PM > > To: Miclaus, Antoniu <Antoniu.Miclaus@xxxxxxxxxx> > > Cc: jic23@xxxxxxxxxx; linux-iio@xxxxxxxxxxxxxxx; > devicetree@xxxxxxxxxxxxxxx; > > linux-kernel@xxxxxxxxxxxxxxx; Sa, Nuno <Nuno.Sa@xxxxxxxxxx> > > Subject: Re: [PATCH v3 2/2] dt-bindings: iio: frequency: add admv1013 doc > > > > [External] > > > > On Mon, Nov 01, 2021 at 12:04:20PM +0200, Antoniu Miclaus wrote: > > > Add device tree bindings for the ADMV1013 Upconverter. > > > > > > Signed-off-by: Antoniu Miclaus <antoniu.miclaus@xxxxxxxxxx> > > > --- > > > .../bindings/iio/frequency/adi,admv1013.yaml | 119 > > ++++++++++++++++++ > > > 1 file changed, 119 insertions(+) > > > create mode 100644 > > Documentation/devicetree/bindings/iio/frequency/adi,admv1013.yaml > > > > > > diff --git > > a/Documentation/devicetree/bindings/iio/frequency/adi,admv1013.yaml > > b/Documentation/devicetree/bindings/iio/frequency/adi,admv1013.yaml > > > new file mode 100644 > > > index 000000000000..47993253a586 > > > --- /dev/null > > > +++ > > b/Documentation/devicetree/bindings/iio/frequency/adi,admv1013.yaml > > > @@ -0,0 +1,119 @@ > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > > +%YAML 1.2 > > > +--- > > > +$id: > > > https://urldefense.com/v3/__http://devicetree.org/schemas/iio/frequency > > > /adi,admv1013.yaml*__;Iw!!A3Ni8CS0y2Y!uTDPalOgj6YS_vZ6bsDSbA_Qna6Q > > OwMpoRxzo6nn06i5TNuGWZEk9PvtbC6SKQGXrugy$ > > > +$schema: https://urldefense.com/v3/__http://devicetree.org/meta- > > > schemas/core.yaml*__;Iw!!A3Ni8CS0y2Y!uTDPalOgj6YS_vZ6bsDSbA_Qna6Q > > OwMpoRxzo6nn06i5TNuGWZEk9PvtbC6SKYugV1fM$ > > > + > > > +title: ADMV1013 Microwave Upconverter > > > + > > > +maintainers: > > > + - Antoniu Miclaus <antoniu.miclaus@xxxxxxxxxx> > > > + > > > +description: | > > > + Wideband, microwave upconverter optimized for point to point > > microwave > > > + radio designs operating in the 24 GHz to 44 GHz frequency range. > > > + > > > + https://www.analog.com/en/products/admv1013.html > > > + > > > +properties: > > > + compatible: > > > + enum: > > > + - adi,admv1013 > > > + > > > + reg: > > > + maxItems: 1 > > > + > > > + spi-max-frequency: > > > + maximum: 1000000 > > > + > > > + clocks: > > > + description: > > > + Definition of the external clock. > > > + minItems: 1 > > > + > > > + clock-names: > > > + items: > > > + - const: lo_in > > > + > > > + clock-output-names: > > > + maxItems: 1 > > > + > > > + vcm-supply: > > > + description: > > > + Analog voltage regulator. > > > + > > > + adi,vga-powerdown: > > > + description: > > > + Power Down the Voltage Gain Amplifier Circuit available at > > > + BG_RBIAS2 pin. > > > + type: boolean > > > + > > > + adi,mixer-powerdown: > > > + description: > > > + Power Down the Mixer Circuit. Enable to put the block in > > > + a power down state. > > > + type: boolean > > > + > > > + adi,quad-powerdown: > > > + description: > > > + Power Down the Quadrupler. Enable to put the block in > > > + a power down state. > > > + type: boolean > > > + > > > + adi,bg-powerdown: > > > + description: > > > + Power Down the Transmitter Band Gap. Enable to put the part in > > > + a power down state. > > > + type: boolean > > > + > > > + adi,mixer-if-enable: > > > + description: > > > + Enable the Intermediate Frequency Mode. Either IF Mode or I/Q > Mode > > > + can be enabled at a time. > > > + type: boolean > > > + > > > + adi,detector-enable: > > > + description: > > > + Enable the Envelope Detector available at output pins VENV_P and > > > + VENV_N. Disable to reduce power consumption. > > > + type: boolean > > > + > > > + adi,quad-se-mode: > > > + description: > > > + Switch the LO path from differential to single-ended operation. > > > + Set value 6 for Single-Ended Mode, Negative Side Disabled. > > > + Set value 9 for Single-Ended Mode, Positive Side Disabled. > > > + Set value 12 for Differential Mode. > > > + $ref: /schemas/types.yaml#/definitions/uint32 > > > + enum: [6, 9, 12] > > > > All these vendor properties are fixed based on the board design or > > something a user may want to change? The latter does not belong in DT. > > > > Rob
