This is where we describe the different new and generic options used by
the ST BCH driver.
Cc: devicetree@xxxxxxxxxxxxxxx
Reviewed-By: Pekon Gupta <pekon@xxxxxxxxxxx>
Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
---
Documentation/devicetree/bindings/mtd/stm-nand.txt | 74 ++++++++++++++++++++++
1 file changed, 74 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mtd/stm-nand.txt
diff --git a/Documentation/devicetree/bindings/mtd/stm-nand.txt b/Documentation/devicetree/bindings/mtd/stm-nand.txt
new file mode 100644
index 0000000..5872a39
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/stm-nand.txt
@@ -0,0 +1,74 @@
+STM BCH NAND Support
+--------------------
+
+Required properties:
+
+- compatible : Should be "st,nand-bch"
+- reg : Should contain register's location and length
+- reg-names : "emi_nand" - NAND Controller register map
+ "emiss" - External Memory Interface Subsystem base
+- interrupts : Interrupt number
+- interrupt-names : "nand_irq" - NAND Controller IRQ
+- st,nand-banks : Subnode representing one or more "banks" of NAND
+ Flash, connected to an STM NAND Controller (see
+ description below).
+- nand-ecc-strength : Generic NAND property (See mtd/nand.txt)
+ Options are; 0, 18 or 30. If not present, the driver
+ will choose the strongest scheme compatible if the
+ OOB size.
+
+Properties describing Bank of NAND Flash ("st,nand-banks"):
+
+- st,nand-csn : Chip select associated with the Bank.
+
+- st,nand-timing-relax : [Optional] Number of IP clock cycles by which to
+ "relax" timing configuration. Required on some boards
+ to accommodate board-level limitations. Applies to
+ ONFI timing mode configuration.
+
+- nand-on-flash-bbt : Generic NAND property (See mtd/nand.txt)
+
+- partitions : [Optional] Subnode describing MTD partition map
+ (see mtd/partition.txt)
+
+Note, during initialisation, the NAND Controller timing registers are configured
+according to one of the following methods, in order of precedence:
+
+ 1. Configuration based on ONFI timing mode, as advertised by the
+ device during ONFI-probing (ONFI-compliant NAND only).
+
+ 2. Use reset/safe timing values
+
+Example:
+
+ nand@fe901000 {
+ compatible = "st,nand-bch";
+ reg = <0xfe901000 0x1000>, <0xfef00800 0x0800>;
+ reg-names = "emi_nand", "emiss";
+ interrupts = <0 139 0x0>;
+ interrupt-names = "nand_irq";
+ nand-ecc-strength = <30>;
+
+ status = "okay";
+
+ bank0 {
+ /* NAND_BBT_USE_FLASH */
+ nand-on-flash-bbt;
+ st,nand-csn = <0>;
+
+ partitions {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0{
+ label = "NANDFlash1";
+ reg = <0x00000000 0x00800000>;
+ };
+
+ partition@800000{
+ label = "NANDFlash2";
+ reg = <0x00800000 0x0f800000>;
+ };
+ };
+ };
+ };
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
