On 10/28/21 9:35 PM, Rob Herring wrote:
On Thu, Oct 28, 2021 at 10:19 AM Sean Anderson <sean.anderson@xxxxxxxx> wrote:
Hi Rob,
On 10/26/21 10:27 PM, Rob Herring wrote:
> On Mon, Oct 18, 2021 at 07:49:21PM -0400, Sean Anderson wrote:
>> This adds a binding for a generic GPIO reset driver. This driver is
>> designed to easily add a GPIO-based reset to a driver which expected a
>> reset controller. It offers greater flexibility than a reset-gpios
>> property, and allows for one code path to be shared for GPIO resets and
>> MMIO-based resets.
>
> I would like to do this last part, but not requiring a binding change.
> IOW, be able to register any 'reset-gpios' property as a reset provider
> directly without this added level of indirection.
That would be nice, but it seems like someone would have to go through
every driver with a reset-gpios property and convert them. Since the
reset GPIOs are
All that has to happen is when a driver requests a reset, the reset
subsystem can check for a 'reset-gpios' when there is not a 'resets'
property. If it finds one, then it can either instantiate a reset
provider or add that GPIO to an existing provider. Then you can
convert drivers one by one, or not.
I will have a stab at this.
>>
>> Signed-off-by: Sean Anderson <sean.anderson@xxxxxxxx>
>> ---
>>
>> .../devicetree/bindings/reset/gpio-reset.yaml | 93 +++++++++++++++++++
>> 1 file changed, 93 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/reset/gpio-reset.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/reset/gpio-reset.yaml b/Documentation/devicetree/bindings/reset/gpio-reset.yaml
>> new file mode 100644
>> index 000000000000..de2ab074cea3
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/reset/gpio-reset.yaml
>> @@ -0,0 +1,93 @@
>> +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause)
>
> GPL-2.0-only not GPL-2.0+
GPL-2.0+ is a strict superset. And bindings are required to be BSD
anyway. I don't see the issue.
Not everyone agrees with GPLv3. What about GPLv4, v5, etc.? You're
okay with them no matter what they say?
So you would rather have GPL-2.0-only OR GPL-3.0-only OR BSD-2-Clause :)
The issue is many people pay no attention. Just copy whatever they
started from, or put whatever they want. The dts files are a mess. The
binding docs all defaulted to GPL2. So I'm fixing the mess with
bindings and that means dictating the license.
Ok
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/reset/gpio-reset.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Generic GPIO reset driver
>> +
>> +maintainers:
>> + - Sean Anderson <seanga2@xxxxxxxxx>
>> +
>> +description: |
>> + This is a generic GPIO reset driver which can provide a reset-controller
>> + interface for GPIO-based reset lines. This driver always operates with
>> + logical GPIO values; to invert the polarity, specify GPIO_ACTIVE_LOW in the
>> + GPIO's flags.
>> +
>> +properties:
>> + compatible:
>> + const: gpio-reset
>> +
>> + '#reset-cells':
>> + const: 1
>> +
>> + reset-gpios:
>> + description: |
>> + GPIOs to assert when asserting a reset. There is a one-to-one mapping
>> + between the reset specifier and the index of the GPIO in this list to
>> + assert.
>> +
>> + done-gpios:
>> + description: |
>> + GPIOs which indicate that the device controlled by the GPIO has exited
>> + reset. There must be one done GPIO for each reset GPIO, or no done GPIOs
>> + at all. The driver will wait for up to done-timeout-us for the
>> + corresponding done GPIO to assert before returning.
>
> This is odd. Do you have some examples of h/w needing this done signal?
> It certainly doesn't seem like something we have a generic need for.
Yes [1]. This device has a "reset done" signal, but no reset timings
specified in the datasheet. I don't know if this is truly needed,
because we can read the ID register, but it is nice when bringing up the
device. I left it in because I was using it.
Okay, but done-gpios belongs in the device node that has a done
signal. Your binding pretty assumes you always have one because you
need equal numbers of reset and done gpios.
Have two devices, one with done GPIOs, and one without.
Anyways, I don't think this binding is going anywhere.
[1] https://lore.kernel.org/netdev/20211004191527.1610759-16-sean.anderson@xxxxxxxx/
>> +
>> + pre-assert-us:
>> + default: 0
>> + description: |
>> + Microseconds to delay between when the reset was requested to be
>> + asserted, and asserting the reset GPIO
>> +
>> + post-assert-us:
>> + default: 0
>> + description: |
>> + Microseconds to delay after asserting the reset GPIO and before returning
>> + to the caller.
>> +
>> + pre-deassert-us:
>> + default: 0
>> + description: |
>> + Microseconds to delay between when the reset was requested to be
>> + deasserted, and asserting the reset GPIO
>> +
>> + post-deassert-us:
>> + default: 0
>> + description: |
>> + Microseconds to delay after deasserting the reset GPIO and before
>> + returning to the caller. This delay is always present, even if the done
>> + GPIO goes high earlier.
>> +
>> + done-timeout-us:
>> + default: 1000
>> + description:
>> + Microseconds to wait for the done GPIO to assert after deasserting the
>> + reset GPIO. If post-deassert-us is present, this property defaults to 10
>> + times that delay. The timeout starts after waiting for the post deassert
>> + delay.
>
> There's a reason we don't have all these timing values in DT. The timing
> requirements are defined by each device (being reset) and implied by
> their compatible strings. If we wanted a macro language for power
> sequence timings of regulators, clocks, resets, enables, etc., then we
> would have designed such a thing already.
Well, there are already things like reset-assert-us and
reset-deassert-us in [2, 3, 4] (with different names(!)).
Yes, things evolve poorly. What's just one more property added at a time.
Part of what I
want to address with this device is that there are several existing
properties which specify various aspects of the above timings. I think
it would be good to standardize on these. Maybe this should be a
property which applies to the reset consumer? Analogously, we also
have assigned-clocks so that not every driver has to know what the
correct frequency/parent is (especially when they can vary among
different hardware variations).
Yes, there are some examples, but you won't find many new examples.
The rule is power sequencing requirements/timing is implied by the
device's compatible string.
You are looking at just reset. What about timing WRT regulators and
clocks for starters?
*shrug*
This just seems like a very common area which needs to customized.
--Sean
