This series is the final step of a long process of porting 80+ devices to use the new qca8k driver instead of the hacky qca one based on never merged swconfig platform. Some background to justify all these additions. QCA used a special binding to declare raw initval to set the swich. I made a script to convert all these magic values and convert 80+ dts and scan all the needed "unsupported regs". We find a baseline where we manage to find the common and used regs so in theory hopefully we don't have to add anymore things. We discovered lots of things with this, especially about how differently qca8327 works compared to qca8337. In short, we found that qca8327 have some problem with suspend/resume for their internal phy. It instead sets some dedicated regs that suspend the phy without setting the standard bit. First 4 patch are to fix this. There is also a patch about preferring master. This is directly from the original driver and it seems to be needed to prevent some problem with the pause frame. Every ipq806x target sets the mac power sel and this specific reg regulates the output voltage of the regulator. Without this some instability can occur. Some configuration (for some reason) swap mac6 with mac0. We add support for this. Also, we discovered that some device doesn't work at all with pll enabled for sgmii line. In the original code this was based on the switch revision. In later revision the pll regs were decided based on the switch type (disabled for qca8327 and enabled for qca8337) but still some device had that disabled in the initval regs. Considering we found at least one qca8337 device that required pll disabled to work (no traffic problem) we decided to introduce a binding to enable pll and set it only with that. Lastly, we add support for led open drain that require the power-on-sel to set. Also, some device have only the power-on-sel set in the initval so we add also support for that. This is needed for the correct function of the switch leds. Qca8327 have a special reg in the pws regs that set it to a reduced 48pin layout. This is needed or the switch doesn't work. These are all the special configuration we find on all these devices that are from various targets. Mostly ath79, ipq806x and bcm53xx. Changes v6: - Convert Documentation to yaml - Add extra check for cpu port and invalid phy mode - Add co developed by tag to give credits to Matthew Changes v5: - Swap patch. Document first then implement. - Fix some grammar error reported. - Rework function. Remove phylink mac_config DT scan and move everything to dedicated function in probe. - Introduce new logic for delay selection where is also supported with internal delay declared and rgmii set as phy mode - Start working on ymal conversion. Will later post this in v6 when we finally take final decision about mac swap. Changes v4: - Fix typo in SGMII falling edge about using PHY id instead of switch id Changes v3: - Drop phy patches (proposed separateley) - Drop special pwr binding. Rework to ipq806x specific - Better describe compatible and add serial print on switch chip - Drop mac exchange. Rework falling edge and move it to mac_config - Add support for port 6 cpu port. Drop hardcoded cpu port to port0 - Improve port stability with sgmii. QCA source have intenal delay also for sgmii - Add warning with pll enabled on wrong configuration Changes v2: - Reword Documentation patch to dt-bindings - Propose first 2 phy patch to net - Better describe and add hint on how to use all the new bindings - Rework delay scan function and move to phylink mac_config - Drop package48 wrong binding - Introduce support for qca8328 switch - Fix wrong binding name power-on-sel - Return error on wrong config with led open drain and ignore-power-on-sel not set Ansuel Smith (15): dsa: qca8k: add mac_power_sel support dt-bindings: net: dsa: qca8k: Add SGMII clock phase properties net: dsa: qca8k: add support for sgmii falling edge dt-bindings: net: dsa: qca8k: Document support for CPU port 6 net: dsa: qca8k: add support for cpu port 6 net: dsa: qca8k: rework rgmii delay logic and scan for cpu port 6 dt-bindings: net: dsa: qca8k: Document qca,sgmii-enable-pll net: dsa: qca8k: add explicit SGMII PLL enable dt-bindings: net: dsa: qca8k: Document qca,led-open-drain binding net: dsa: qca8k: add support for pws config reg dt-bindings: net: dsa: qca8k: document support for qca8328 net: dsa: qca8k: add support for QCA8328 net: dsa: qca8k: set internal delay also for sgmii net: dsa: qca8k: move port config to dedicated struct dt-bindings: net: ipq8064-mdio: fix warning with new qca8k switch Matthew Hagan (1): dt-bindings: net: dsa: qca8k: convert to YAML schema .../devicetree/bindings/net/dsa/qca8k.txt | 215 ----------- .../devicetree/bindings/net/dsa/qca8k.yaml | 362 +++++++++++++++++ .../bindings/net/qcom,ipq8064-mdio.yaml | 5 +- drivers/net/dsa/qca8k.c | 364 ++++++++++++++---- drivers/net/dsa/qca8k.h | 35 +- 5 files changed, 685 insertions(+), 296 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/dsa/qca8k.txt create mode 100644 Documentation/devicetree/bindings/net/dsa/qca8k.yaml -- 2.32.0
