The mpc5xxx platforms have had dts warnings for some time which no one
seems to care to fix, so let's just remove the dts files.
According to Arnd:
"Specifically, MPC5200B has a 15 year lifetime, which ends in
11 months from now. The original bplan/Genesi Efika 5K2 was
quite popular at the time it came out, and there are probably
still some of those hanging around, but they came with Open
Firmware rather than relying on the dts files that ship with the
kernel.
Grant Likely was the original maintainer for MPC52xx until 2011,
Anatolij Gustschin is still listed as maintainer since then but hasn't
been active in it for a while either. Anatolij can probably best judge
which of these boards are still in going to be used with future kernels,
but I suspect once you start removing bits from 52xx, the newer
but less common 512x platform can go away as well."
Cc: Anatolij Gustschin <agust@xxxxxxx>
Cc: Arnd Bergmann <arnd@xxxxxxxx>
Cc: Stephen Rothwell <sfr@xxxxxxxxxxxxxxxx>
Cc: Michael Ellerman <mpe@xxxxxxxxxxxxxx>
Cc: Benjamin Herrenschmidt <benh@xxxxxxxxxxxxxxxxxxx>
Cc: Paul Mackerras <paulus@xxxxxxxxx>
Cc: linuxppc-dev@xxxxxxxxxxxxxxxx
Signed-off-by: Rob Herring <robh@xxxxxxxxxx>
---
Sending this out as a feeler to see if anyone cares. If anyone does,
please fix the warnings.
arch/powerpc/boot/Makefile | 5 -
arch/powerpc/boot/dts/a3m071.dts | 138 -------
arch/powerpc/boot/dts/a4m072.dts | 147 --------
arch/powerpc/boot/dts/ac14xx.dts | 395 --------------------
arch/powerpc/boot/dts/cm5200.dts | 85 -----
arch/powerpc/boot/dts/lite5200b.dts | 157 --------
arch/powerpc/boot/dts/media5200.dts | 142 --------
arch/powerpc/boot/dts/motionpro.dts | 132 -------
arch/powerpc/boot/dts/mpc5121.dtsi | 526 ---------------------------
arch/powerpc/boot/dts/mpc5121ads.dts | 174 ---------
arch/powerpc/boot/dts/mpc5125twr.dts | 293 ---------------
arch/powerpc/boot/dts/mpc5200b.dtsi | 288 ---------------
arch/powerpc/boot/dts/mucmc52.dts | 222 -----------
arch/powerpc/boot/dts/o2d.dts | 43 ---
arch/powerpc/boot/dts/o2d.dtsi | 118 ------
arch/powerpc/boot/dts/o2d300.dts | 48 ---
arch/powerpc/boot/dts/o2dnt2.dts | 44 ---
arch/powerpc/boot/dts/o2i.dts | 29 --
arch/powerpc/boot/dts/o2mnt.dts | 29 --
arch/powerpc/boot/dts/o3dnt.dts | 44 ---
arch/powerpc/boot/dts/pcm030.dts | 106 ------
arch/powerpc/boot/dts/pcm032.dts | 183 ----------
arch/powerpc/boot/dts/pdm360ng.dts | 195 ----------
arch/powerpc/boot/dts/uc101.dts | 152 --------
24 files changed, 3695 deletions(-)
delete mode 100644 arch/powerpc/boot/dts/a3m071.dts
delete mode 100644 arch/powerpc/boot/dts/a4m072.dts
delete mode 100644 arch/powerpc/boot/dts/ac14xx.dts
delete mode 100644 arch/powerpc/boot/dts/cm5200.dts
delete mode 100644 arch/powerpc/boot/dts/lite5200b.dts
delete mode 100644 arch/powerpc/boot/dts/media5200.dts
delete mode 100644 arch/powerpc/boot/dts/motionpro.dts
delete mode 100644 arch/powerpc/boot/dts/mpc5121.dtsi
delete mode 100644 arch/powerpc/boot/dts/mpc5121ads.dts
delete mode 100644 arch/powerpc/boot/dts/mpc5125twr.dts
delete mode 100644 arch/powerpc/boot/dts/mpc5200b.dtsi
delete mode 100644 arch/powerpc/boot/dts/mucmc52.dts
delete mode 100644 arch/powerpc/boot/dts/o2d.dts
delete mode 100644 arch/powerpc/boot/dts/o2d.dtsi
delete mode 100644 arch/powerpc/boot/dts/o2d300.dts
delete mode 100644 arch/powerpc/boot/dts/o2dnt2.dts
delete mode 100644 arch/powerpc/boot/dts/o2i.dts
delete mode 100644 arch/powerpc/boot/dts/o2mnt.dts
delete mode 100644 arch/powerpc/boot/dts/o3dnt.dts
delete mode 100644 arch/powerpc/boot/dts/pcm030.dts
delete mode 100644 arch/powerpc/boot/dts/pcm032.dts
delete mode 100644 arch/powerpc/boot/dts/pdm360ng.dts
delete mode 100644 arch/powerpc/boot/dts/uc101.dts
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index 6900d0ac2421..15ee0c2c6a3e 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -308,11 +308,6 @@ image-$(CONFIG_PPC_EP88XC) += dtbImage.ep88xc
image-$(CONFIG_PPC_ADDER875) += cuImage.adder875-uboot \
dtbImage.adder875-redboot
-# Board ports in arch/powerpc/platform/52xx/Kconfig
-image-$(CONFIG_PPC_LITE5200) += cuImage.lite5200
-image-$(CONFIG_PPC_LITE5200) += cuImage.lite5200b
-image-$(CONFIG_PPC_MEDIA5200) += cuImage.media5200
-
# Board ports in arch/powerpc/platform/82xx/Kconfig
image-$(CONFIG_MPC8272_ADS) += cuImage.mpc8272ads
image-$(CONFIG_PQ2FADS) += cuImage.pq2fads
diff --git a/arch/powerpc/boot/dts/a3m071.dts b/arch/powerpc/boot/dts/a3m071.dts
deleted file mode 100644
index 034cfd8aa95b..000000000000
--- a/arch/powerpc/boot/dts/a3m071.dts
+++ /dev/null
@@ -1,138 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * a3m071 board Device Tree Source
- *
- * Copyright 2012 Stefan Roese <sr@xxxxxxx>
- *
- * Copyright (C) 2011 DENX Software Engineering GmbH
- * Heiko Schocher <hs@xxxxxxx>
- *
- * Copyright (C) 2007 Semihalf
- * Marian Balakowicz <m8@xxxxxxxxxxxx>
- */
-
-/include/ "mpc5200b.dtsi"
-
-&gpt0 { fsl,has-wdt; };
-
-/ {
- model = "anonymous,a3m071";
- compatible = "anonymous,a3m071";
-
- soc5200@f0000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc5200b-immr";
- ranges = <0 0xf0000000 0x0000c000>;
- reg = <0xf0000000 0x00000100>;
- bus-frequency = <0>; /* From boot loader */
- system-frequency = <0>; /* From boot loader */
-
- spi@f00 {
- status = "disabled";
- };
-
- usb: usb@1000 {
- status = "disabled";
- };
-
- psc@2000 {
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- reg = <0x2000 0x100>;
- interrupts = <2 1 0>;
- };
-
- psc@2200 {
- status = "disabled";
- };
-
- psc@2400 {
- status = "disabled";
- };
-
- psc@2600 {
- status = "disabled";
- };
-
- psc@2800 {
- status = "disabled";
- };
-
- psc@2c00 { // PSC6
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- reg = <0x2c00 0x100>;
- interrupts = <2 4 0>;
- };
-
- ethernet@3000 {
- phy-handle = <&phy0>;
- };
-
- mdio@3000 {
- phy0: ethernet-phy@3 {
- reg = <0x03>;
- };
- };
-
- ata@3a00 {
- status = "disabled";
- };
-
- i2c@3d00 {
- status = "disabled";
- };
-
- i2c@3d40 {
- status = "disabled";
- };
- };
-
- localbus {
- compatible = "fsl,mpc5200b-lpb","simple-bus";
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0xfc000000 0x02000000
- 3 0 0xe9000000 0x00080000
- 5 0 0xe8000000 0x00010000>;
-
- flash@0,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0 0x0 0x02000000>;
- compatible = "cfi-flash";
- bank-width = <2>;
- partition@0 {
- label = "u-boot";
- reg = <0x00000000 0x00040000>;
- read-only;
- };
- partition@40000 {
- label = "env";
- reg = <0x00040000 0x00020000>;
- };
- partition@60000 {
- label = "dtb";
- reg = <0x00060000 0x00020000>;
- };
- partition@80000 {
- label = "kernel";
- reg = <0x00080000 0x00500000>;
- };
- partition@580000 {
- label = "root";
- reg = <0x00580000 0x00A80000>;
- };
- };
-
- fpga@3,0 {
- compatible = "anonymous,a3m071-fpga";
- reg = <3 0x0 0x00080000
- 5 0x0 0x00010000>;
- interrupts = <0 0 3>; /* level low */
- };
- };
-
- pci@f0000d00 {
- status = "disabled";
- };
-};
diff --git a/arch/powerpc/boot/dts/a4m072.dts b/arch/powerpc/boot/dts/a4m072.dts
deleted file mode 100644
index a9cef5726422..000000000000
--- a/arch/powerpc/boot/dts/a4m072.dts
+++ /dev/null
@@ -1,147 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * a4m072 board Device Tree Source
- *
- * Copyright (C) 2011 DENX Software Engineering GmbH
- * Heiko Schocher <hs@xxxxxxx>
- *
- * Copyright (C) 2007 Semihalf
- * Marian Balakowicz <m8@xxxxxxxxxxxx>
- */
-
-/include/ "mpc5200b.dtsi"
-
-&gpt0 { fsl,has-wdt; };
-&gpt3 { gpio-controller; };
-&gpt4 { gpio-controller; };
-&gpt5 { gpio-controller; };
-
-/ {
- model = "anonymous,a4m072";
- compatible = "anonymous,a4m072";
-
- soc5200@f0000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc5200b-immr";
- ranges = <0 0xf0000000 0x0000c000>;
- reg = <0xf0000000 0x00000100>;
- bus-frequency = <0>; /* From boot loader */
- system-frequency = <0>; /* From boot loader */
-
- cdm@200 {
- fsl,init-ext-48mhz-en = <0x0>;
- fsl,init-fd-enable = <0x01>;
- fsl,init-fd-counters = <0x3333>;
- };
-
- spi@f00 {
- status = "disabled";
- };
-
- psc@2000 {
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- reg = <0x2000 0x100>;
- interrupts = <2 1 0>;
- };
-
- psc@2200 {
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- reg = <0x2200 0x100>;
- interrupts = <2 2 0>;
- };
-
- psc@2400 {
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- reg = <0x2400 0x100>;
- interrupts = <2 3 0>;
- };
-
- psc@2600 {
- status = "disabled";
- };
-
- psc@2800 {
- status = "disabled";
- };
-
- psc@2c00 {
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- reg = <0x2c00 0x100>;
- interrupts = <2 4 0>;
- };
-
- ethernet@3000 {
- phy-handle = <&phy0>;
- };
-
- mdio@3000 {
- phy0: ethernet-phy@1f {
- reg = <0x1f>;
- interrupts = <1 2 0>; /* IRQ 2 active low */
- };
- };
-
- i2c@3d00 {
- status = "disabled";
- };
-
- i2c@3d40 {
- hwmon@2e {
- compatible = "nsc,lm87";
- reg = <0x2e>;
- };
- rtc@51 {
- compatible = "nxp,rtc8564";
- reg = <0x51>;
- };
- };
- };
-
- localbus {
- compatible = "fsl,mpc5200b-lpb","simple-bus";
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0xfe000000 0x02000000
- 1 0 0x62000000 0x00400000
- 2 0 0x64000000 0x00200000
- 3 0 0x66000000 0x01000000
- 6 0 0x68000000 0x01000000
- 7 0 0x6a000000 0x00000004>;
-
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x02000000>;
- bank-width = <2>;
- #size-cells = <1>;
- #address-cells = <1>;
- };
- sram0@1,0 {
- compatible = "mtd-ram";
- reg = <1 0x00000 0x00400000>;
- bank-width = <2>;
- };
- };
-
- pci@f0000d00 {
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- compatible = "fsl,mpc5200-pci";
- reg = <0xf0000d00 0x100>;
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x16 */
- 0xc000 0 0 1 &mpc5200_pic 1 3 3
- 0xc000 0 0 2 &mpc5200_pic 1 3 3
- 0xc000 0 0 3 &mpc5200_pic 1 3 3
- 0xc000 0 0 4 &mpc5200_pic 1 3 3>;
- clock-frequency = <0>; /* From boot loader */
- interrupts = <2 8 0 2 9 0 2 10 0>;
- bus-range = <0 0>;
- ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000
- 0x02000000 0 0x90000000 0x90000000 0 0x10000000
- 0x01000000 0 0x00000000 0xa0000000 0 0x01000000>;
- };
-};
diff --git a/arch/powerpc/boot/dts/ac14xx.dts b/arch/powerpc/boot/dts/ac14xx.dts
deleted file mode 100644
index 5d8877e1f4ad..000000000000
--- a/arch/powerpc/boot/dts/ac14xx.dts
+++ /dev/null
@@ -1,395 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Device Tree Source for the MPC5121e based ac14xx board
- *
- * Copyright 2012 Anatolij Gustschin <agust@xxxxxxx>
- */
-
-
-#include "mpc5121.dtsi"
-
-/ {
- model = "ac14xx";
- compatible = "ifm,ac14xx", "fsl,mpc5121";
- #address-cells = <1>;
- #size-cells = <1>;
-
- aliases {
- serial0 = &serial0;
- serial1 = &serial7;
- spi4 = &spi4;
- spi5 = &spi5;
- };
-
- cpus {
- PowerPC,5121@0 {
- timebase-frequency = <40000000>; /* 40 MHz (csb/4) */
- bus-frequency = <160000000>; /* 160 MHz csb bus */
- clock-frequency = <400000000>; /* 400 MHz ppc core */
- };
- };
-
- memory {
- reg = <0x00000000 0x10000000>; /* 256MB at 0 */
- };
-
- nfc@40000000 {
- status = "disabled";
- };
-
- localbus@80000020 {
- ranges = <0x0 0x0 0xfc000000 0x04000000 /* CS0: NOR flash */
- 0x1 0x0 0xe0000000 0x00010000 /* CS1: FRAM */
- 0x2 0x0 0xe0100000 0x00080000 /* CS2: asi1 */
- 0x3 0x0 0xe0300000 0x00020000 /* CS3: comm */
- 0x5 0x0 0xe0400000 0x00010000 /* CS5: safety */
- 0x6 0x0 0xe0200000 0x00080000>; /* CS6: asi2 */
-
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0x00000000 0x04000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- bank-width = <2>;
- device-width = <2>;
-
- partition@0 {
- label = "dtb-kernel-production";
- reg = <0x00000000 0x00400000>;
- };
- partition@1 {
- label = "filesystem-production";
- reg = <0x00400000 0x03400000>;
- };
-
- partition@2 {
- label = "recovery";
- reg = <0x03800000 0x00700000>;
- };
-
- partition@3 {
- label = "uboot-code";
- reg = <0x03f00000 0x00040000>;
- };
- partition@4 {
- label = "uboot-env1";
- reg = <0x03f40000 0x00020000>;
- };
- partition@5 {
- label = "uboot-env2";
- reg = <0x03f60000 0x00020000>;
- };
- };
-
- fram@1,0 {
- compatible = "ifm,ac14xx-fram", "linux,uio-pdrv-genirq";
- reg = <1 0x00000000 0x00010000>;
- };
-
- asi@2,0 {
- /* masters mapping: CS, CS offset, size */
- reg = <2 0x00000000 0x00080000
- 6 0x00000000 0x00080000>;
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "ifm,ac14xx-asi-fpga";
- gpios = <
- &gpio_pic 26 0 /* prog */
- &gpio_pic 27 0 /* done */
- &gpio_pic 10 0 /* reset */
- >;
-
- master@1 {
- interrupts = <20 0x2>;
- interrupt-parent = <&gpio_pic>;
- chipselect = <2 0x00009000 0x00009100>;
- label = "AS-i master 1";
- };
-
- master@2 {
- interrupts = <21 0x2>;
- interrupt-parent = <&gpio_pic>;
- chipselect = <6 0x00009000 0x00009100>;
- label = "AS-i master 2";
- };
- };
-
- netx@3,0 {
- compatible = "ifm,netx";
- reg = <0x3 0x00000000 0x00020000>;
- chipselect = <3 0x00101140 0x00203100>;
- interrupts = <17 0x8>;
- gpios = <&gpio_pic 15 0>;
- };
-
- safety@5,0 {
- compatible = "ifm,safety";
- reg = <0x5 0x00000000 0x00010000>;
- chipselect = <5 0x00009000 0x00009100>;
- interrupts = <22 0x2>;
- interrupt-parent = <&gpio_pic>;
- gpios = <
- &gpio_pic 12 0 /* prog */
- &gpio_pic 11 0 /* done */
- >;
- };
- };
-
- clocks {
- osc {
- clock-frequency = <25000000>;
- };
- };
-
- soc@80000000 {
- bus-frequency = <80000000>; /* 80 MHz ips bus */
-
- clock@f00 {
- compatible = "fsl,mpc5121rev2-clock", "fsl,mpc5121-clock";
- };
-
- /*
- * GPIO PIC:
- * interrupts cell = <pin nr, sense>
- * sense == 8: Level, low assertion
- * sense == 2: Edge, high-to-low change
- */
- gpio_pic: gpio@1100 {
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- sdhc@1500 {
- cd-gpios = <&gpio_pic 23 0>; /* card detect */
- wp-gpios = <&gpio_pic 24 0>; /* write protect */
- wp-inverted; /* WP active high */
- };
-
- i2c@1700 {
- /* use Fast-mode */
- clock-frequency = <400000>;
-
- at24@30 {
- compatible = "atmel,24c01";
- reg = <0x30>;
- };
-
- at24@31 {
- compatible = "atmel,24c01";
- reg = <0x31>;
- };
-
- temp@48 {
- compatible = "ad,ad7414";
- reg = <0x48>;
- };
-
- at24@50 {
- compatible = "atmel,24c01";
- reg = <0x50>;
- };
-
- at24@51 {
- compatible = "atmel,24c01";
- reg = <0x51>;
- };
-
- at24@52 {
- compatible = "atmel,24c01";
- reg = <0x52>;
- };
-
- at24@53 {
- compatible = "atmel,24c01";
- reg = <0x53>;
- };
-
- at24@54 {
- compatible = "atmel,24c01";
- reg = <0x54>;
- };
-
- at24@55 {
- compatible = "atmel,24c01";
- reg = <0x55>;
- };
-
- at24@56 {
- compatible = "atmel,24c01";
- reg = <0x56>;
- };
-
- at24@57 {
- compatible = "atmel,24c01";
- reg = <0x57>;
- };
-
- rtc@68 {
- compatible = "st,m41t00";
- reg = <0x68>;
- };
- };
-
- axe_pic: axe-base@2000 {
- compatible = "fsl,mpc5121-axe-base";
- reg = <0x2000 0x100>;
- interrupts = <42 0x8>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- axe-app {
- compatible = "fsl,mpc5121-axe-app";
- interrupt-parent = <&axe_pic>;
- interrupts = <
- /* soft interrupts */
- 0 0x0 1 0x0 2 0x0 3 0x0
- 4 0x0 5 0x0 6 0x0 7 0x0
- /* fifo interrupts */
- 8 0x0 9 0x0 10 0x0 11 0x0
- >;
- };
-
- display@2100 {
- edid = [00 FF FF FF FF FF FF 00 14 94 00 00 00 00 00 00
- 0A 12 01 03 80 1C 23 78 CA 88 FF 94 52 54 8E 27
- 1E 4C 50 00 00 00 01 01 01 01 01 01 01 01 01 01
- 01 01 01 01 01 01 FB 00 B0 14 00 DC 05 00 08 04
- 21 00 1C 23 00 00 00 18 00 00 00 FD 00 38 3C 1F
- 3C 01 0A 20 20 20 20 20 20 20 00 00 00 FC 00 45
- 54 30 31 38 30 30 33 44 4D 55 0A 0A 00 00 00 10
- 00 41 30 30 30 30 30 30 30 30 30 30 30 31 00 D5];
- };
-
- can@2300 {
- status = "disabled";
- };
-
- can@2380 {
- status = "disabled";
- };
-
- viu@2400 {
- status = "disabled";
- };
-
- mdio@2800 {
- phy0: ethernet-phy@1f {
- compatible = "smsc,lan8700";
- reg = <0x1f>;
- };
- };
-
- enet: ethernet@2800 {
- phy-handle = <&phy0>;
- };
-
- usb@3000 {
- status = "disabled";
- };
-
- usb@4000 {
- status = "disabled";
- };
-
- /* PSC3 serial port A, aka ttyPSC0 */
- serial0: psc@11300 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- fsl,rx-fifo-size = <512>;
- fsl,tx-fifo-size = <512>;
- };
-
- /* PSC4 in SPI mode */
- spi4: psc@11400 {
- compatible = "fsl,mpc5121-psc-spi", "fsl,mpc5121-psc";
- fsl,rx-fifo-size = <768>;
- fsl,tx-fifo-size = <768>;
- #address-cells = <1>;
- #size-cells = <0>;
- num-cs = <1>;
- cs-gpios = <&gpio_pic 25 0>;
-
- flash: m25p128@0 {
- compatible = "st,m25p128";
- spi-max-frequency = <20000000>;
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "spi-flash0";
- reg = <0x00000000 0x01000000>;
- };
- };
- };
-
- /* PSC5 in SPI mode */
- spi5: psc@11500 {
- compatible = "fsl,mpc5121-psc-spi", "fsl,mpc5121-psc";
- fsl,mode = "spi-master";
- fsl,rx-fifo-size = <128>;
- fsl,tx-fifo-size = <128>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- lcd@0 {
- compatible = "ilitek,ili922x";
- reg = <0>;
- spi-max-frequency = <100000>;
- spi-cpol;
- spi-cpha;
- };
- };
-
- /* PSC7 serial port C, aka ttyPSC2 */
- serial7: psc@11700 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- fsl,rx-fifo-size = <512>;
- fsl,tx-fifo-size = <512>;
- };
-
- matrix_keypad@0 {
- compatible = "gpio-matrix-keypad";
- debounce-delay-ms = <5>;
- col-scan-delay-us = <1>;
- gpio-activelow;
- col-gpios-binary;
- col-switch-delay-ms = <200>;
-
- col-gpios = <&gpio_pic 1 0>; /* pin1 */
-
- row-gpios = <&gpio_pic 2 0 /* pin2 */
- &gpio_pic 3 0 /* pin3 */
- &gpio_pic 4 0>; /* pin4 */
-
- linux,keymap = <0x0000006e /* FN LEFT */
- 0x01000067 /* UP */
- 0x02000066 /* FN RIGHT */
- 0x00010069 /* LEFT */
- 0x0101006a /* DOWN */
- 0x0201006c>; /* RIGHT */
- };
- };
-
- leds {
- compatible = "gpio-leds";
-
- backlight {
- label = "backlight";
- gpios = <&gpio_pic 0 0>;
- default-state = "keep";
- };
- green {
- label = "green";
- gpios = <&gpio_pic 18 0>;
- default-state = "keep";
- };
- red {
- label = "red";
- gpios = <&gpio_pic 19 0>;
- default-state = "keep";
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts
deleted file mode 100644
index 66cae7be60c4..000000000000
--- a/arch/powerpc/boot/dts/cm5200.dts
+++ /dev/null
@@ -1,85 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * CM5200 board Device Tree Source
- *
- * Copyright (C) 2007 Semihalf
- * Marian Balakowicz <m8@xxxxxxxxxxxx>
- */
-
-/include/ "mpc5200b.dtsi"
-
-&gpt0 { fsl,has-wdt; };
-
-/ {
- model = "schindler,cm5200";
- compatible = "schindler,cm5200";
-
- soc5200@f0000000 {
- can@900 {
- status = "disabled";
- };
-
- can@980 {
- status = "disabled";
- };
-
- psc@2000 { // PSC1
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- psc@2200 { // PSC2
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- psc@2400 { // PSC3
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- psc@2600 { // PSC4
- status = "disabled";
- };
-
- psc@2800 { // PSC5
- status = "disabled";
- };
-
- psc@2c00 { // PSC6
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- ethernet@3000 {
- phy-handle = <&phy0>;
- };
-
- mdio@3000 {
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
- };
-
- ata@3a00 {
- status = "disabled";
- };
-
- i2c@3d00 {
- status = "disabled";
- };
-
- };
-
- pci@f0000d00 {
- status = "disabled";
- };
-
- localbus {
- // 16-bit flash device at LocalPlus Bus CS0
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x2000000>;
- bank-width = <2>;
- device-width = <2>;
- #size-cells = <1>;
- #address-cells = <1>;
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/lite5200b.dts b/arch/powerpc/boot/dts/lite5200b.dts
deleted file mode 100644
index 2b86c81f9048..000000000000
--- a/arch/powerpc/boot/dts/lite5200b.dts
+++ /dev/null
@@ -1,157 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Lite5200B board Device Tree Source
- *
- * Copyright 2006-2007 Secret Lab Technologies Ltd.
- * Grant Likely <grant.likely@xxxxxxxxxxxx>
- */
-
-/include/ "mpc5200b.dtsi"
-
-&gpt0 { fsl,has-wdt; };
-&gpt2 { gpio-controller; };
-&gpt3 { gpio-controller; };
-
-/ {
- model = "fsl,lite5200b";
- compatible = "fsl,lite5200b";
-
- leds {
- compatible = "gpio-leds";
- tmr2 {
- gpios = <&gpt2 0 1>;
- };
- tmr3 {
- gpios = <&gpt3 0 1>;
- linux,default-trigger = "heartbeat";
- };
- led1 { gpios = <&gpio_wkup 2 1>; };
- led2 { gpios = <&gpio_simple 3 1>; };
- led3 { gpios = <&gpio_wkup 3 1>; };
- led4 { gpios = <&gpio_simple 2 1>; };
- };
-
- memory {
- reg = <0x00000000 0x10000000>; // 256MB
- };
-
- soc5200@f0000000 {
- psc@2000 { // PSC1
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- cell-index = <0>;
- };
-
- psc@2200 { // PSC2
- status = "disabled";
- };
-
- psc@2400 { // PSC3
- status = "disabled";
- };
-
- psc@2600 { // PSC4
- status = "disabled";
- };
-
- psc@2800 { // PSC5
- status = "disabled";
- };
-
- psc@2c00 { // PSC6
- status = "disabled";
- };
-
- // PSC2 in ac97 mode example
- //ac97@2200 { // PSC2
- // compatible = "fsl,mpc5200b-psc-ac97","fsl,mpc5200-psc-ac97";
- // cell-index = <1>;
- //};
-
- // PSC3 in CODEC mode example
- //i2s@2400 { // PSC3
- // compatible = "fsl,mpc5200b-psc-i2s"; //not 5200 compatible
- // cell-index = <2>;
- //};
-
- // PSC6 in spi mode example
- //spi@2c00 { // PSC6
- // compatible = "fsl,mpc5200b-psc-spi","fsl,mpc5200-psc-spi";
- // cell-index = <5>;
- //};
-
- ethernet@3000 {
- phy-handle = <&phy0>;
- };
-
- mdio@3000 {
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
- };
-
- i2c@3d40 {
- eeprom@50 {
- compatible = "atmel,24c02";
- reg = <0x50>;
- };
- };
-
- sram@8000 {
- compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
- reg = <0x8000 0x4000>;
- };
- };
-
- pci@f0000d00 {
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
- 0xc000 0 0 2 &mpc5200_pic 1 1 3
- 0xc000 0 0 3 &mpc5200_pic 1 2 3
- 0xc000 0 0 4 &mpc5200_pic 1 3 3
-
- 0xc800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
- 0xc800 0 0 2 &mpc5200_pic 1 2 3
- 0xc800 0 0 3 &mpc5200_pic 1 3 3
- 0xc800 0 0 4 &mpc5200_pic 0 0 3>;
- clock-frequency = <0>; // From boot loader
- interrupts = <2 8 0 2 9 0 2 10 0>;
- bus-range = <0 0>;
- ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
- 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
- 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
- };
-
- localbus {
- ranges = <0 0 0xfe000000 0x02000000>;
-
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x02000000>;
- bank-width = <1>;
- #size-cells = <1>;
- #address-cells = <1>;
-
- partition@0 {
- label = "kernel";
- reg = <0x00000000 0x00200000>;
- };
- partition@200000 {
- label = "rootfs";
- reg = <0x00200000 0x01d00000>;
- };
- partition@1f00000 {
- label = "u-boot";
- reg = <0x01f00000 0x00060000>;
- };
- partition@1f60000 {
- label = "u-boot-env";
- reg = <0x01f60000 0x00020000>;
- };
- partition@1f80000 {
- label = "dtb";
- reg = <0x01f80000 0x00080000>;
- };
- };
- };
-
-};
diff --git a/arch/powerpc/boot/dts/media5200.dts b/arch/powerpc/boot/dts/media5200.dts
deleted file mode 100644
index 61cae9dcddef..000000000000
--- a/arch/powerpc/boot/dts/media5200.dts
+++ /dev/null
@@ -1,142 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Freescale Media5200 board Device Tree Source
- *
- * Copyright 2009 Secret Lab Technologies Ltd.
- * Grant Likely <grant.likely@xxxxxxxxxxxx>
- * Steven Cavanagh <scavanagh@xxxxxxxxxxxx>
- */
-
-/include/ "mpc5200b.dtsi"
-
-&gpt0 { fsl,has-wdt; };
-
-/ {
- model = "fsl,media5200";
- compatible = "fsl,media5200";
-
- aliases {
- console = &console;
- ethernet0 = ð0;
- };
-
- chosen {
- stdout-path = &console;
- };
-
- cpus {
- PowerPC,5200@0 {
- timebase-frequency = <33000000>; // 33 MHz, these were configured by U-Boot
- bus-frequency = <132000000>; // 132 MHz
- clock-frequency = <396000000>; // 396 MHz
- };
- };
-
- memory {
- reg = <0x00000000 0x08000000>; // 128MB RAM
- };
-
- soc5200@f0000000 {
- bus-frequency = <132000000>;// 132 MHz
-
- psc@2000 { // PSC1
- status = "disabled";
- };
-
- psc@2200 { // PSC2
- status = "disabled";
- };
-
- psc@2400 { // PSC3
- status = "disabled";
- };
-
- psc@2600 { // PSC4
- status = "disabled";
- };
-
- psc@2800 { // PSC5
- status = "disabled";
- };
-
- // PSC6 in uart mode
- console: psc@2c00 { // PSC6
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- ethernet@3000 {
- phy-handle = <&phy0>;
- };
-
- mdio@3000 {
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
- };
-
- usb@1000 {
- reg = <0x1000 0x100>;
- };
- };
-
- pci@f0000d00 {
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <0xc000 0 0 1 &media5200_fpga 0 2 // 1st slot
- 0xc000 0 0 2 &media5200_fpga 0 3
- 0xc000 0 0 3 &media5200_fpga 0 4
- 0xc000 0 0 4 &media5200_fpga 0 5
-
- 0xc800 0 0 1 &media5200_fpga 0 3 // 2nd slot
- 0xc800 0 0 2 &media5200_fpga 0 4
- 0xc800 0 0 3 &media5200_fpga 0 5
- 0xc800 0 0 4 &media5200_fpga 0 2
-
- 0xd000 0 0 1 &media5200_fpga 0 4 // miniPCI
- 0xd000 0 0 2 &media5200_fpga 0 5
-
- 0xe000 0 0 1 &media5200_fpga 0 5 // CoralIP
- >;
- ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
- 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
- 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
- interrupt-parent = <&mpc5200_pic>;
- };
-
- localbus {
- ranges = < 0 0 0xfc000000 0x02000000
- 1 0 0xfe000000 0x02000000
- 2 0 0xf0010000 0x00010000
- 3 0 0xf0020000 0x00010000 >;
- flash@0,0 {
- compatible = "amd,am29lv28ml", "cfi-flash";
- reg = <0 0x0 0x2000000>; // 32 MB
- bank-width = <4>; // Width in bytes of the flash bank
- device-width = <2>; // Two devices on each bank
- };
-
- flash@1,0 {
- compatible = "amd,am29lv28ml", "cfi-flash";
- reg = <1 0 0x2000000>; // 32 MB
- bank-width = <4>; // Width in bytes of the flash bank
- device-width = <2>; // Two devices on each bank
- };
-
- media5200_fpga: fpga@2,0 {
- compatible = "fsl,media5200-fpga";
- interrupt-controller;
- #interrupt-cells = <2>; // 0:bank 1:id; no type field
- reg = <2 0 0x10000>;
-
- interrupt-parent = <&mpc5200_pic>;
- interrupts = <0 0 3 // IRQ bank 0
- 1 1 3>; // IRQ bank 1
- };
-
- uart@3,0 {
- compatible = "ti,tl16c752bpt";
- reg = <3 0 0x10000>;
- interrupt-parent = <&media5200_fpga>;
- interrupts = <0 0 0 1>; // 2 irqs
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts
deleted file mode 100644
index c23676093da8..000000000000
--- a/arch/powerpc/boot/dts/motionpro.dts
+++ /dev/null
@@ -1,132 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Motion-PRO board Device Tree Source
- *
- * Copyright (C) 2007 Semihalf
- * Marian Balakowicz <m8@xxxxxxxxxxxx>
- */
-
-/include/ "mpc5200b.dtsi"
-
-&gpt0 { fsl,has-wdt; };
-&gpt6 { // Motion-PRO status LED
- compatible = "promess,motionpro-led";
- label = "motionpro-statusled";
- blink-delay = <100>; // 100 msec
-};
-&gpt7 { // Motion-PRO ready LED
- compatible = "promess,motionpro-led";
- label = "motionpro-readyled";
-};
-
-/ {
- model = "promess,motionpro";
- compatible = "promess,motionpro";
-
- soc5200@f0000000 {
- can@900 {
- status = "disabled";
- };
-
- psc@2000 { // PSC1
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- // PSC2 in spi master mode
- psc@2200 { // PSC2
- compatible = "fsl,mpc5200b-psc-spi","fsl,mpc5200-psc-spi";
- cell-index = <1>;
- };
-
- psc@2400 { // PSC3
- status = "disabled";
- };
-
- psc@2600 { // PSC4
- status = "disabled";
- };
-
- psc@2800 { // PSC5
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- psc@2c00 { // PSC6
- status = "disabled";
- };
-
- ethernet@3000 {
- phy-handle = <&phy0>;
- };
-
- mdio@3000 {
- phy0: ethernet-phy@2 {
- reg = <2>;
- };
- };
-
- i2c@3d00 {
- status = "disabled";
- };
-
- i2c@3d40 {
- rtc@68 {
- compatible = "dallas,ds1339";
- reg = <0x68>;
- };
- };
-
- sram@8000 {
- compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
- reg = <0x8000 0x4000>;
- };
- };
-
- pci@f0000d00 {
- status = "disabled";
- };
-
- localbus {
- ranges = <0 0 0xff000000 0x01000000
- 1 0 0x50000000 0x00010000
- 2 0 0x50010000 0x00010000
- 3 0 0x50020000 0x00010000>;
-
- // 8-bit DualPort SRAM on LocalPlus Bus CS1
- kollmorgen@1,0 {
- compatible = "promess,motionpro-kollmorgen";
- reg = <1 0 0x10000>;
- interrupts = <1 1 0>;
- };
-
- // 8-bit board CPLD on LocalPlus Bus CS2
- cpld@2,0 {
- compatible = "promess,motionpro-cpld";
- reg = <2 0 0x10000>;
- };
-
- // 8-bit custom Anybus Module on LocalPlus Bus CS3
- anybus@3,0 {
- compatible = "promess,motionpro-anybus";
- reg = <3 0 0x10000>;
- };
- pro_module_general@3,0 {
- compatible = "promess,pro_module_general";
- reg = <3 0 3>;
- };
- pro_module_dio@3,800 {
- compatible = "promess,pro_module_dio";
- reg = <3 0x800 2>;
- };
-
- // 16-bit flash device at LocalPlus Bus CS0
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x01000000>;
- bank-width = <2>;
- device-width = <2>;
- #size-cells = <1>;
- #address-cells = <1>;
- };
-
- };
-};
diff --git a/arch/powerpc/boot/dts/mpc5121.dtsi b/arch/powerpc/boot/dts/mpc5121.dtsi
deleted file mode 100644
index 3f66b91a8e3c..000000000000
--- a/arch/powerpc/boot/dts/mpc5121.dtsi
+++ /dev/null
@@ -1,526 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * base MPC5121 Device Tree Source
- *
- * Copyright 2007-2008 Freescale Semiconductor Inc.
- */
-
-#include <dt-bindings/clock/mpc512x-clock.h>
-
-/dts-v1/;
-
-/ {
- model = "mpc5121";
- compatible = "fsl,mpc5121";
- #address-cells = <1>;
- #size-cells = <1>;
- interrupt-parent = <&ipic>;
-
- aliases {
- ethernet0 = ð0;
- pci = &pci;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,5121@0 {
- device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <0x20>; /* 32 bytes */
- i-cache-line-size = <0x20>; /* 32 bytes */
- d-cache-size = <0x8000>; /* L1, 32K */
- i-cache-size = <0x8000>; /* L1, 32K */
- timebase-frequency = <49500000>;/* 49.5 MHz (csb/4) */
- bus-frequency = <198000000>; /* 198 MHz csb bus */
- clock-frequency = <396000000>; /* 396 MHz ppc core */
- };
- };
-
- memory {
- device_type = "memory";
- reg = <0x00000000 0x10000000>; /* 256MB at 0 */
- };
-
- mbx@20000000 {
- compatible = "fsl,mpc5121-mbx";
- reg = <0x20000000 0x4000>;
- interrupts = <66 0x8>;
- clocks = <&clks MPC512x_CLK_MBX_BUS>,
- <&clks MPC512x_CLK_MBX_3D>,
- <&clks MPC512x_CLK_MBX>;
- clock-names = "mbx-bus", "mbx-3d", "mbx";
- };
-
- sram@30000000 {
- compatible = "fsl,mpc5121-sram";
- reg = <0x30000000 0x20000>; /* 128K at 0x30000000 */
- };
-
- nfc@40000000 {
- compatible = "fsl,mpc5121-nfc";
- reg = <0x40000000 0x100000>; /* 1M at 0x40000000 */
- interrupts = <6 8>;
- #address-cells = <1>;
- #size-cells = <1>;
- clocks = <&clks MPC512x_CLK_NFC>;
- clock-names = "ipg";
- };
-
- localbus@80000020 {
- compatible = "fsl,mpc5121-localbus";
- #address-cells = <2>;
- #size-cells = <1>;
- reg = <0x80000020 0x40>;
- ranges = <0x0 0x0 0xfc000000 0x04000000>;
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <0>;
-
- osc: osc {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <33000000>;
- };
- };
-
- soc@80000000 {
- compatible = "fsl,mpc5121-immr";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0x0 0x80000000 0x400000>;
- reg = <0x80000000 0x400000>;
- bus-frequency = <66000000>; /* 66 MHz ips bus */
-
-
- /*
- * IPIC
- * interrupts cell = <intr #, sense>
- * sense values match linux IORESOURCE_IRQ_* defines:
- * sense == 8: Level, low assertion
- * sense == 2: Edge, high-to-low change
- */
- ipic: interrupt-controller@c00 {
- compatible = "fsl,mpc5121-ipic", "fsl,ipic";
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0xc00 0x100>;
- };
-
- /* Watchdog timer */
- wdt@900 {
- compatible = "fsl,mpc5121-wdt";
- reg = <0x900 0x100>;
- };
-
- /* Real time clock */
- rtc@a00 {
- compatible = "fsl,mpc5121-rtc";
- reg = <0xa00 0x100>;
- interrupts = <79 0x8 80 0x8>;
- };
-
- /* Reset module */
- reset@e00 {
- compatible = "fsl,mpc5121-reset";
- reg = <0xe00 0x100>;
- };
-
- /* Clock control */
- clks: clock@f00 {
- compatible = "fsl,mpc5121-clock";
- reg = <0xf00 0x100>;
- #clock-cells = <1>;
- clocks = <&osc>;
- clock-names = "osc";
- };
-
- /* Power Management Controller */
- pmc@1000{
- compatible = "fsl,mpc5121-pmc";
- reg = <0x1000 0x100>;
- interrupts = <83 0x8>;
- };
-
- gpio@1100 {
- compatible = "fsl,mpc5121-gpio";
- reg = <0x1100 0x100>;
- interrupts = <78 0x8>;
- };
-
- can@1300 {
- compatible = "fsl,mpc5121-mscan";
- reg = <0x1300 0x80>;
- interrupts = <12 0x8>;
- clocks = <&clks MPC512x_CLK_BDLC>,
- <&clks MPC512x_CLK_IPS>,
- <&clks MPC512x_CLK_SYS>,
- <&clks MPC512x_CLK_REF>,
- <&clks MPC512x_CLK_MSCAN0_MCLK>;
- clock-names = "ipg", "ips", "sys", "ref", "mclk";
- };
-
- can@1380 {
- compatible = "fsl,mpc5121-mscan";
- reg = <0x1380 0x80>;
- interrupts = <13 0x8>;
- clocks = <&clks MPC512x_CLK_BDLC>,
- <&clks MPC512x_CLK_IPS>,
- <&clks MPC512x_CLK_SYS>,
- <&clks MPC512x_CLK_REF>,
- <&clks MPC512x_CLK_MSCAN1_MCLK>;
- clock-names = "ipg", "ips", "sys", "ref", "mclk";
- };
-
- sdhc@1500 {
- compatible = "fsl,mpc5121-sdhc";
- reg = <0x1500 0x100>;
- interrupts = <8 0x8>;
- dmas = <&dma0 30>;
- dma-names = "rx-tx";
- clocks = <&clks MPC512x_CLK_IPS>,
- <&clks MPC512x_CLK_SDHC>;
- clock-names = "ipg", "per";
- };
-
- i2c@1700 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- reg = <0x1700 0x20>;
- interrupts = <9 0x8>;
- clocks = <&clks MPC512x_CLK_I2C>;
- clock-names = "ipg";
- };
-
- i2c@1720 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- reg = <0x1720 0x20>;
- interrupts = <10 0x8>;
- clocks = <&clks MPC512x_CLK_I2C>;
- clock-names = "ipg";
- };
-
- i2c@1740 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- reg = <0x1740 0x20>;
- interrupts = <11 0x8>;
- clocks = <&clks MPC512x_CLK_I2C>;
- clock-names = "ipg";
- };
-
- i2ccontrol@1760 {
- compatible = "fsl,mpc5121-i2c-ctrl";
- reg = <0x1760 0x8>;
- };
-
- axe@2000 {
- compatible = "fsl,mpc5121-axe";
- reg = <0x2000 0x100>;
- interrupts = <42 0x8>;
- clocks = <&clks MPC512x_CLK_AXE>;
- clock-names = "ipg";
- };
-
- display@2100 {
- compatible = "fsl,mpc5121-diu";
- reg = <0x2100 0x100>;
- interrupts = <64 0x8>;
- clocks = <&clks MPC512x_CLK_DIU>;
- clock-names = "ipg";
- };
-
- can@2300 {
- compatible = "fsl,mpc5121-mscan";
- reg = <0x2300 0x80>;
- interrupts = <90 0x8>;
- clocks = <&clks MPC512x_CLK_BDLC>,
- <&clks MPC512x_CLK_IPS>,
- <&clks MPC512x_CLK_SYS>,
- <&clks MPC512x_CLK_REF>,
- <&clks MPC512x_CLK_MSCAN2_MCLK>;
- clock-names = "ipg", "ips", "sys", "ref", "mclk";
- };
-
- can@2380 {
- compatible = "fsl,mpc5121-mscan";
- reg = <0x2380 0x80>;
- interrupts = <91 0x8>;
- clocks = <&clks MPC512x_CLK_BDLC>,
- <&clks MPC512x_CLK_IPS>,
- <&clks MPC512x_CLK_SYS>,
- <&clks MPC512x_CLK_REF>,
- <&clks MPC512x_CLK_MSCAN3_MCLK>;
- clock-names = "ipg", "ips", "sys", "ref", "mclk";
- };
-
- viu@2400 {
- compatible = "fsl,mpc5121-viu";
- reg = <0x2400 0x400>;
- interrupts = <67 0x8>;
- clocks = <&clks MPC512x_CLK_VIU>;
- clock-names = "ipg";
- };
-
- mdio@2800 {
- compatible = "fsl,mpc5121-fec-mdio";
- reg = <0x2800 0x800>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clks MPC512x_CLK_FEC>;
- clock-names = "per";
- };
-
- eth0: ethernet@2800 {
- device_type = "network";
- compatible = "fsl,mpc5121-fec";
- reg = <0x2800 0x800>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <4 0x8>;
- clocks = <&clks MPC512x_CLK_FEC>;
- clock-names = "per";
- };
-
- /* USB1 using external ULPI PHY */
- usb@3000 {
- compatible = "fsl,mpc5121-usb2-dr";
- reg = <0x3000 0x600>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <43 0x8>;
- dr_mode = "otg";
- phy_type = "ulpi";
- clocks = <&clks MPC512x_CLK_USB1>;
- clock-names = "ipg";
- };
-
- /* USB0 using internal UTMI PHY */
- usb@4000 {
- compatible = "fsl,mpc5121-usb2-dr";
- reg = <0x4000 0x600>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <44 0x8>;
- dr_mode = "otg";
- phy_type = "utmi_wide";
- clocks = <&clks MPC512x_CLK_USB2>;
- clock-names = "ipg";
- };
-
- /* IO control */
- ioctl@a000 {
- compatible = "fsl,mpc5121-ioctl";
- reg = <0xA000 0x1000>;
- };
-
- /* LocalPlus controller */
- lpc@10000 {
- compatible = "fsl,mpc5121-lpc";
- reg = <0x10000 0x100>;
- };
-
- sclpc@10100 {
- compatible = "fsl,mpc512x-lpbfifo";
- reg = <0x10100 0x50>;
- interrupts = <7 0x8>;
- dmas = <&dma0 26>;
- dma-names = "rx-tx";
- };
-
- pata@10200 {
- compatible = "fsl,mpc5121-pata";
- reg = <0x10200 0x100>;
- interrupts = <5 0x8>;
- clocks = <&clks MPC512x_CLK_PATA>;
- clock-names = "ipg";
- };
-
- /* 512x PSCs are not 52xx PSC compatible */
-
- /* PSC0 */
- psc@11000 {
- compatible = "fsl,mpc5121-psc";
- reg = <0x11000 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC0>,
- <&clks MPC512x_CLK_PSC0_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- /* PSC1 */
- psc@11100 {
- compatible = "fsl,mpc5121-psc";
- reg = <0x11100 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC1>,
- <&clks MPC512x_CLK_PSC1_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- /* PSC2 */
- psc@11200 {
- compatible = "fsl,mpc5121-psc";
- reg = <0x11200 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC2>,
- <&clks MPC512x_CLK_PSC2_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- /* PSC3 */
- psc@11300 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- reg = <0x11300 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC3>,
- <&clks MPC512x_CLK_PSC3_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- /* PSC4 */
- psc@11400 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- reg = <0x11400 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC4>,
- <&clks MPC512x_CLK_PSC4_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- /* PSC5 */
- psc@11500 {
- compatible = "fsl,mpc5121-psc";
- reg = <0x11500 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC5>,
- <&clks MPC512x_CLK_PSC5_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- /* PSC6 */
- psc@11600 {
- compatible = "fsl,mpc5121-psc";
- reg = <0x11600 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC6>,
- <&clks MPC512x_CLK_PSC6_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- /* PSC7 */
- psc@11700 {
- compatible = "fsl,mpc5121-psc";
- reg = <0x11700 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC7>,
- <&clks MPC512x_CLK_PSC7_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- /* PSC8 */
- psc@11800 {
- compatible = "fsl,mpc5121-psc";
- reg = <0x11800 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC8>,
- <&clks MPC512x_CLK_PSC8_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- /* PSC9 */
- psc@11900 {
- compatible = "fsl,mpc5121-psc";
- reg = <0x11900 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC9>,
- <&clks MPC512x_CLK_PSC9_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- /* PSC10 */
- psc@11a00 {
- compatible = "fsl,mpc5121-psc";
- reg = <0x11a00 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC10>,
- <&clks MPC512x_CLK_PSC10_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- /* PSC11 */
- psc@11b00 {
- compatible = "fsl,mpc5121-psc";
- reg = <0x11b00 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC11>,
- <&clks MPC512x_CLK_PSC11_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- pscfifo@11f00 {
- compatible = "fsl,mpc5121-psc-fifo";
- reg = <0x11f00 0x100>;
- interrupts = <40 0x8>;
- clocks = <&clks MPC512x_CLK_PSC_FIFO>;
- clock-names = "ipg";
- };
-
- dma0: dma@14000 {
- compatible = "fsl,mpc5121-dma";
- reg = <0x14000 0x1800>;
- interrupts = <65 0x8>;
- #dma-cells = <1>;
- };
- };
-
- pci: pci@80008500 {
- compatible = "fsl,mpc5121-pci";
- device_type = "pci";
- interrupts = <1 0x8>;
- clock-frequency = <0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- clocks = <&clks MPC512x_CLK_PCI>;
- clock-names = "ipg";
-
- reg = <0x80008500 0x100 /* internal registers */
- 0x80008300 0x8>; /* config space access registers */
- bus-range = <0x0 0x0>;
- ranges = <0x42000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
- 0x02000000 0x0 0xb0000000 0xb0000000 0x0 0x10000000
- 0x01000000 0x0 0x00000000 0x84000000 0x0 0x01000000>;
- };
-};
diff --git a/arch/powerpc/boot/dts/mpc5121ads.dts b/arch/powerpc/boot/dts/mpc5121ads.dts
deleted file mode 100644
index b407a50ee622..000000000000
--- a/arch/powerpc/boot/dts/mpc5121ads.dts
+++ /dev/null
@@ -1,174 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * MPC5121E ADS Device Tree Source
- *
- * Copyright 2007-2008 Freescale Semiconductor Inc.
- */
-
-#include "mpc5121.dtsi"
-
-/ {
- model = "mpc5121ads";
- compatible = "fsl,mpc5121ads", "fsl,mpc5121";
-
- nfc@40000000 {
- /*
- * ADS has two Hynix 512MB Nand flash chips in a single
- * stacked package.
- */
- chips = <2>;
-
- nand@0 {
- label = "nand";
- reg = <0x00000000 0x40000000>; /* 512MB + 512MB */
- };
- };
-
- localbus@80000020 {
- ranges = <0x0 0x0 0xfc000000 0x04000000
- 0x2 0x0 0x82000000 0x00008000>;
-
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0x0 0x4000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- bank-width = <4>;
- device-width = <2>;
-
- protected@0 {
- label = "protected";
- reg = <0x00000000 0x00040000>; // first sector is protected
- read-only;
- };
- filesystem@40000 {
- label = "filesystem";
- reg = <0x00040000 0x03c00000>; // 60M for filesystem
- };
- kernel@3c40000 {
- label = "kernel";
- reg = <0x03c40000 0x00280000>; // 2.5M for kernel
- };
- device-tree@3ec0000 {
- label = "device-tree";
- reg = <0x03ec0000 0x00040000>; // one sector for device tree
- };
- u-boot@3f00000 {
- label = "u-boot";
- reg = <0x03f00000 0x00100000>; // 1M for u-boot
- read-only;
- };
- };
-
- board-control@2,0 {
- compatible = "fsl,mpc5121ads-cpld";
- reg = <0x2 0x0 0x8000>;
- };
-
- cpld_pic: pic@2,a {
- compatible = "fsl,mpc5121ads-cpld-pic";
- interrupt-controller;
- #interrupt-cells = <2>;
- reg = <0x2 0xa 0x5>;
- /* irq routing:
- * all irqs but touch screen are routed to irq0 (ipic 48)
- * touch screen is statically routed to irq1 (ipic 17)
- * so don't use it here
- */
- interrupts = <48 0x8>;
- };
- };
-
- soc@80000000 {
-
- i2c@1700 {
- fsl,preserve-clocking;
-
- hwmon@4a {
- compatible = "adi,ad7414";
- reg = <0x4a>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c32";
- reg = <0x50>;
- };
-
- rtc@68 {
- compatible = "st,m41t62";
- reg = <0x68>;
- };
- };
-
- eth0: ethernet@2800 {
- phy-handle = <&phy0>;
- };
-
- can@2300 {
- status = "disabled";
- };
-
- can@2380 {
- status = "disabled";
- };
-
- viu@2400 {
- status = "disabled";
- };
-
- mdio@2800 {
- phy0: ethernet-phy@0 {
- reg = <1>;
- };
- };
-
- /* mpc5121ads only uses USB0 */
- usb@3000 {
- status = "disabled";
- };
-
- /* USB0 using internal UTMI PHY */
- usb@4000 {
- dr_mode = "host";
- fsl,invert-drvvbus;
- fsl,invert-pwr-fault;
- };
-
- /* PSC3 serial port A aka ttyPSC0 */
- psc@11300 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- };
-
- /* PSC4 serial port B aka ttyPSC1 */
- psc@11400 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- };
-
- /* PSC5 in ac97 mode */
- ac97: psc@11500 {
- compatible = "fsl,mpc5121-psc-ac97", "fsl,mpc5121-psc";
- fsl,mode = "ac97-slave";
- fsl,rx-fifo-size = <384>;
- fsl,tx-fifo-size = <384>;
- };
- };
-
- pci: pci@80008500 {
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x15 - Slot 1 PCI */
- 0xa800 0x0 0x0 0x1 &cpld_pic 0x0 0x8
- 0xa800 0x0 0x0 0x2 &cpld_pic 0x1 0x8
- 0xa800 0x0 0x0 0x3 &cpld_pic 0x2 0x8
- 0xa800 0x0 0x0 0x4 &cpld_pic 0x3 0x8
-
- /* IDSEL 0x16 - Slot 2 MiniPCI */
- 0xb000 0x0 0x0 0x1 &cpld_pic 0x4 0x8
- 0xb000 0x0 0x0 0x2 &cpld_pic 0x5 0x8
-
- /* IDSEL 0x17 - Slot 3 MiniPCI */
- 0xb800 0x0 0x0 0x1 &cpld_pic 0x6 0x8
- 0xb800 0x0 0x0 0x2 &cpld_pic 0x7 0x8
- >;
- };
-};
diff --git a/arch/powerpc/boot/dts/mpc5125twr.dts b/arch/powerpc/boot/dts/mpc5125twr.dts
deleted file mode 100644
index 0bd2acc0401d..000000000000
--- a/arch/powerpc/boot/dts/mpc5125twr.dts
+++ /dev/null
@@ -1,293 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * STx/Freescale ADS5125 MPC5125 silicon
- *
- * Copyright (C) 2009 Freescale Semiconductor Inc. All rights reserved.
- *
- * Reworked by Matteo Facchinetti (engineering@xxxxxxxxxxxx)
- * Copyright (C) 2013 Sirius Electronic Systems
- */
-
-#include <dt-bindings/clock/mpc512x-clock.h>
-
-/dts-v1/;
-
-/ {
- model = "mpc5125twr"; // In BSP "mpc5125ads"
- compatible = "fsl,mpc5125ads", "fsl,mpc5125";
- #address-cells = <1>;
- #size-cells = <1>;
- interrupt-parent = <&ipic>;
-
- aliases {
- gpio0 = &gpio0;
- gpio1 = &gpio1;
- ethernet0 = ð0;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- PowerPC,5125@0 {
- device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <0x20>; // 32 bytes
- i-cache-line-size = <0x20>; // 32 bytes
- d-cache-size = <0x8000>; // L1, 32K
- i-cache-size = <0x8000>; // L1, 32K
- timebase-frequency = <49500000>;// 49.5 MHz (csb/4)
- bus-frequency = <198000000>; // 198 MHz csb bus
- clock-frequency = <396000000>; // 396 MHz ppc core
- };
- };
-
- memory {
- device_type = "memory";
- reg = <0x00000000 0x10000000>; // 256MB at 0
- };
-
- sram@30000000 {
- compatible = "fsl,mpc5121-sram";
- reg = <0x30000000 0x08000>; // 32K at 0x30000000
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <0>;
-
- osc: osc {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <33000000>;
- };
- };
-
- soc@80000000 {
- compatible = "fsl,mpc5121-immr";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0x0 0x80000000 0x400000>;
- reg = <0x80000000 0x400000>;
- bus-frequency = <66000000>; // 66 MHz ips bus
-
- // IPIC
- // interrupts cell = <intr #, sense>
- // sense values match linux IORESOURCE_IRQ_* defines:
- // sense == 8: Level, low assertion
- // sense == 2: Edge, high-to-low change
- //
- ipic: interrupt-controller@c00 {
- compatible = "fsl,mpc5121-ipic", "fsl,ipic";
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- reg = <0xc00 0x100>;
- };
-
- rtc@a00 { // Real time clock
- compatible = "fsl,mpc5121-rtc";
- reg = <0xa00 0x100>;
- interrupts = <79 0x8 80 0x8>;
- };
-
- reset@e00 { // Reset module
- compatible = "fsl,mpc5125-reset";
- reg = <0xe00 0x100>;
- };
-
- clks: clock@f00 { // Clock control
- compatible = "fsl,mpc5121-clock";
- reg = <0xf00 0x100>;
- #clock-cells = <1>;
- clocks = <&osc>;
- clock-names = "osc";
- };
-
- pmc@1000{ // Power Management Controller
- compatible = "fsl,mpc5121-pmc";
- reg = <0x1000 0x100>;
- interrupts = <83 0x2>;
- };
-
- gpio0: gpio@1100 {
- compatible = "fsl,mpc5125-gpio";
- reg = <0x1100 0x080>;
- interrupts = <78 0x8>;
- };
-
- gpio1: gpio@1180 {
- compatible = "fsl,mpc5125-gpio";
- reg = <0x1180 0x080>;
- interrupts = <86 0x8>;
- };
-
- can@1300 { // CAN rev.2
- compatible = "fsl,mpc5121-mscan";
- interrupts = <12 0x8>;
- reg = <0x1300 0x80>;
- clocks = <&clks MPC512x_CLK_BDLC>,
- <&clks MPC512x_CLK_IPS>,
- <&clks MPC512x_CLK_SYS>,
- <&clks MPC512x_CLK_REF>,
- <&clks MPC512x_CLK_MSCAN0_MCLK>;
- clock-names = "ipg", "ips", "sys", "ref", "mclk";
- };
-
- can@1380 {
- compatible = "fsl,mpc5121-mscan";
- interrupts = <13 0x8>;
- reg = <0x1380 0x80>;
- clocks = <&clks MPC512x_CLK_BDLC>,
- <&clks MPC512x_CLK_IPS>,
- <&clks MPC512x_CLK_SYS>,
- <&clks MPC512x_CLK_REF>,
- <&clks MPC512x_CLK_MSCAN1_MCLK>;
- clock-names = "ipg", "ips", "sys", "ref", "mclk";
- };
-
- sdhc@1500 {
- compatible = "fsl,mpc5121-sdhc";
- interrupts = <8 0x8>;
- reg = <0x1500 0x100>;
- clocks = <&clks MPC512x_CLK_IPS>,
- <&clks MPC512x_CLK_SDHC>;
- clock-names = "ipg", "per";
- };
-
- i2c@1700 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- reg = <0x1700 0x20>;
- interrupts = <0x9 0x8>;
- clocks = <&clks MPC512x_CLK_I2C>;
- clock-names = "ipg";
- };
-
- i2c@1720 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- reg = <0x1720 0x20>;
- interrupts = <0xa 0x8>;
- clocks = <&clks MPC512x_CLK_I2C>;
- clock-names = "ipg";
- };
-
- i2c@1740 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- reg = <0x1740 0x20>;
- interrupts = <0xb 0x8>;
- clocks = <&clks MPC512x_CLK_I2C>;
- clock-names = "ipg";
- };
-
- i2ccontrol@1760 {
- compatible = "fsl,mpc5121-i2c-ctrl";
- reg = <0x1760 0x8>;
- };
-
- diu@2100 {
- compatible = "fsl,mpc5121-diu";
- reg = <0x2100 0x100>;
- interrupts = <64 0x8>;
- clocks = <&clks MPC512x_CLK_DIU>;
- clock-names = "ipg";
- };
-
- mdio@2800 {
- compatible = "fsl,mpc5121-fec-mdio";
- reg = <0x2800 0x800>;
- #address-cells = <1>;
- #size-cells = <0>;
- phy0: ethernet-phy@0 {
- reg = <1>;
- };
- };
-
- eth0: ethernet@2800 {
- compatible = "fsl,mpc5125-fec";
- reg = <0x2800 0x800>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <4 0x8>;
- phy-handle = < &phy0 >;
- phy-connection-type = "rmii";
- clocks = <&clks MPC512x_CLK_FEC>;
- clock-names = "per";
- };
-
- // IO control
- ioctl@a000 {
- compatible = "fsl,mpc5125-ioctl";
- reg = <0xA000 0x1000>;
- };
-
- // disable USB1 port
- // TODO:
- // correct pinmux config and fix USB3320 ulpi dependency
- // before re-enabling it
- usb@3000 {
- compatible = "fsl,mpc5121-usb2-dr";
- reg = <0x3000 0x400>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <43 0x8>;
- dr_mode = "host";
- phy_type = "ulpi";
- clocks = <&clks MPC512x_CLK_USB1>;
- clock-names = "ipg";
- status = "disabled";
- };
-
- sclpc@10100 {
- compatible = "fsl,mpc512x-lpbfifo";
- reg = <0x10100 0x50>;
- interrupts = <7 0x8>;
- dmas = <&dma0 26>;
- dma-names = "rx-tx";
- };
-
- // 5125 PSCs are not 52xx or 5121 PSC compatible
- // PSC1 uart0 aka ttyPSC0
- serial@11100 {
- compatible = "fsl,mpc5125-psc-uart", "fsl,mpc5125-psc";
- reg = <0x11100 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC1>,
- <&clks MPC512x_CLK_PSC1_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- // PSC9 uart1 aka ttyPSC1
- serial@11900 {
- compatible = "fsl,mpc5125-psc-uart", "fsl,mpc5125-psc";
- reg = <0x11900 0x100>;
- interrupts = <40 0x8>;
- fsl,rx-fifo-size = <16>;
- fsl,tx-fifo-size = <16>;
- clocks = <&clks MPC512x_CLK_PSC9>,
- <&clks MPC512x_CLK_PSC9_MCLK>;
- clock-names = "ipg", "mclk";
- };
-
- pscfifo@11f00 {
- compatible = "fsl,mpc5121-psc-fifo";
- reg = <0x11f00 0x100>;
- interrupts = <40 0x8>;
- clocks = <&clks MPC512x_CLK_PSC_FIFO>;
- clock-names = "ipg";
- };
-
- dma0: dma@14000 {
- compatible = "fsl,mpc5121-dma"; // BSP name: "mpc512x-dma2"
- reg = <0x14000 0x1800>;
- interrupts = <65 0x8>;
- #dma-cells = <1>;
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/mpc5200b.dtsi b/arch/powerpc/boot/dts/mpc5200b.dtsi
deleted file mode 100644
index 648fe31795f4..000000000000
--- a/arch/powerpc/boot/dts/mpc5200b.dtsi
+++ /dev/null
@@ -1,288 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * base MPC5200b Device Tree Source
- *
- * Copyright (C) 2010 SecretLab
- * Grant Likely <grant@xxxxxxxxxxxx>
- * John Bonesio <bones@xxxxxxxxxxxx>
- */
-
-/dts-v1/;
-
-/ {
- model = "fsl,mpc5200b";
- compatible = "fsl,mpc5200b";
- #address-cells = <1>;
- #size-cells = <1>;
- interrupt-parent = <&mpc5200_pic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- powerpc: PowerPC,5200@0 {
- device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <32>;
- i-cache-line-size = <32>;
- d-cache-size = <0x4000>; // L1, 16K
- i-cache-size = <0x4000>; // L1, 16K
- timebase-frequency = <0>; // from bootloader
- bus-frequency = <0>; // from bootloader
- clock-frequency = <0>; // from bootloader
- };
- };
-
- memory: memory {
- device_type = "memory";
- reg = <0x00000000 0x04000000>; // 64MB
- };
-
- soc: soc5200@f0000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc5200b-immr";
- ranges = <0 0xf0000000 0x0000c000>;
- reg = <0xf0000000 0x00000100>;
- bus-frequency = <0>; // from bootloader
- system-frequency = <0>; // from bootloader
-
- cdm@200 {
- compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
- reg = <0x200 0x38>;
- };
-
- mpc5200_pic: interrupt-controller@500 {
- // 5200 interrupts are encoded into two levels;
- interrupt-controller;
- #interrupt-cells = <3>;
- compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
- reg = <0x500 0x80>;
- };
-
- gpt0: timer@600 { // General Purpose Timer
- compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- #gpio-cells = <2>; // Add 'gpio-controller;' to enable gpio mode
- reg = <0x600 0x10>;
- interrupts = <1 9 0>;
- // add 'fsl,has-wdt' to enable watchdog
- };
-
- gpt1: timer@610 { // General Purpose Timer
- compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- #gpio-cells = <2>; // Add 'gpio-controller;' to enable gpio mode
- reg = <0x610 0x10>;
- interrupts = <1 10 0>;
- };
-
- gpt2: timer@620 { // General Purpose Timer
- compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- #gpio-cells = <2>; // Add 'gpio-controller;' to enable gpio mode
- reg = <0x620 0x10>;
- interrupts = <1 11 0>;
- };
-
- gpt3: timer@630 { // General Purpose Timer
- compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- #gpio-cells = <2>; // Add 'gpio-controller;' to enable gpio mode
- reg = <0x630 0x10>;
- interrupts = <1 12 0>;
- };
-
- gpt4: timer@640 { // General Purpose Timer
- compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- #gpio-cells = <2>; // Add 'gpio-controller;' to enable gpio mode
- reg = <0x640 0x10>;
- interrupts = <1 13 0>;
- };
-
- gpt5: timer@650 { // General Purpose Timer
- compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- #gpio-cells = <2>; // Add 'gpio-controller;' to enable gpio mode
- reg = <0x650 0x10>;
- interrupts = <1 14 0>;
- };
-
- gpt6: timer@660 { // General Purpose Timer
- compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- #gpio-cells = <2>; // Add 'gpio-controller;' to enable gpio mode
- reg = <0x660 0x10>;
- interrupts = <1 15 0>;
- };
-
- gpt7: timer@670 { // General Purpose Timer
- compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- #gpio-cells = <2>; // Add 'gpio-controller;' to enable gpio mode
- reg = <0x670 0x10>;
- interrupts = <1 16 0>;
- };
-
- rtc@800 { // Real time clock
- compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
- reg = <0x800 0x100>;
- interrupts = <1 5 0 1 6 0>;
- };
-
- can@900 {
- compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
- interrupts = <2 17 0>;
- reg = <0x900 0x80>;
- };
-
- can@980 {
- compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
- interrupts = <2 18 0>;
- reg = <0x980 0x80>;
- };
-
- gpio_simple: gpio@b00 {
- compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
- reg = <0xb00 0x40>;
- interrupts = <1 7 0>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- gpio_wkup: gpio@c00 {
- compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
- reg = <0xc00 0x40>;
- interrupts = <1 8 0 0 3 0>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- spi@f00 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
- reg = <0xf00 0x20>;
- interrupts = <2 13 0 2 14 0>;
- };
-
- usb: usb@1000 {
- compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
- reg = <0x1000 0xff>;
- interrupts = <2 6 0>;
- };
-
- dma-controller@1200 {
- compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
- reg = <0x1200 0x80>;
- interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
- 3 4 0 3 5 0 3 6 0 3 7 0
- 3 8 0 3 9 0 3 10 0 3 11 0
- 3 12 0 3 13 0 3 14 0 3 15 0>;
- };
-
- xlb@1f00 {
- compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
- reg = <0x1f00 0x100>;
- };
-
- psc1: psc@2000 { // PSC1
- compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
- reg = <0x2000 0x100>;
- interrupts = <2 1 0>;
- };
-
- psc2: psc@2200 { // PSC2
- compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
- reg = <0x2200 0x100>;
- interrupts = <2 2 0>;
- };
-
- psc3: psc@2400 { // PSC3
- compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
- reg = <0x2400 0x100>;
- interrupts = <2 3 0>;
- };
-
- psc4: psc@2600 { // PSC4
- compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
- reg = <0x2600 0x100>;
- interrupts = <2 11 0>;
- };
-
- psc5: psc@2800 { // PSC5
- compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
- reg = <0x2800 0x100>;
- interrupts = <2 12 0>;
- };
-
- psc6: psc@2c00 { // PSC6
- compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
- reg = <0x2c00 0x100>;
- interrupts = <2 4 0>;
- };
-
- eth0: ethernet@3000 {
- compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
- reg = <0x3000 0x400>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <2 5 0>;
- };
-
- mdio@3000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
- reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts
- interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
- };
-
- ata@3a00 {
- compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
- reg = <0x3a00 0x100>;
- interrupts = <2 7 0>;
- };
-
- sclpc@3c00 {
- compatible = "fsl,mpc5200-lpbfifo";
- reg = <0x3c00 0x60>;
- interrupts = <2 23 0>;
- };
-
- i2c@3d00 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
- reg = <0x3d00 0x40>;
- interrupts = <2 15 0>;
- };
-
- i2c@3d40 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
- reg = <0x3d40 0x40>;
- interrupts = <2 16 0>;
- };
-
- sram@8000 {
- compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
- reg = <0x8000 0x4000>;
- };
- };
-
- pci: pci@f0000d00 {
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
- reg = <0xf0000d00 0x100>;
- // interrupt-map-mask = need to add
- // interrupt-map = need to add
- clock-frequency = <0>; // From boot loader
- interrupts = <2 8 0 2 9 0 2 10 0>;
- bus-range = <0 0>;
- // ranges = need to add
- };
-
- localbus: localbus {
- compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0xfc000000 0x2000000>;
- };
-};
diff --git a/arch/powerpc/boot/dts/mucmc52.dts b/arch/powerpc/boot/dts/mucmc52.dts
deleted file mode 100644
index c6c66306308d..000000000000
--- a/arch/powerpc/boot/dts/mucmc52.dts
+++ /dev/null
@@ -1,222 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Manroland mucmc52 board Device Tree Source
- *
- * Copyright (C) 2009 DENX Software Engineering GmbH
- * Heiko Schocher <hs@xxxxxxx>
- * Copyright 2006-2007 Secret Lab Technologies Ltd.
- */
-
-/include/ "mpc5200b.dtsi"
-
-/* Timer pins that need to be in GPIO mode */
-&gpt0 { gpio-controller; };
-&gpt1 { gpio-controller; };
-&gpt2 { gpio-controller; };
-&gpt3 { gpio-controller; };
-
-/* Disabled timers */
-&gpt4 { status = "disabled"; };
-&gpt5 { status = "disabled"; };
-&gpt6 { status = "disabled"; };
-&gpt7 { status = "disabled"; };
-
-/ {
- model = "manroland,mucmc52";
- compatible = "manroland,mucmc52";
-
- soc5200@f0000000 {
- rtc@800 {
- status = "disabled";
- };
-
- can@900 {
- status = "disabled";
- };
-
- can@980 {
- status = "disabled";
- };
-
- spi@f00 {
- status = "disabled";
- };
-
- usb@1000 {
- status = "disabled";
- };
-
- psc@2000 { // PSC1
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- psc@2200 { // PSC2
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- psc@2400 { // PSC3
- status = "disabled";
- };
-
- psc@2600 { // PSC4
- status = "disabled";
- };
-
- psc@2800 { // PSC5
- status = "disabled";
- };
-
- psc@2c00 { // PSC6
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- ethernet@3000 {
- phy-handle = <&phy0>;
- };
-
- mdio@3000 {
- phy0: ethernet-phy@0 {
- compatible = "intel,lxt971";
- reg = <0>;
- };
- };
-
- i2c@3d00 {
- status = "disabled";
- };
-
- i2c@3d40 {
- hwmon@2c {
- compatible = "ad,adm9240";
- reg = <0x2c>;
- };
- rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
- };
- };
-
- pci@f0000d00 {
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <
- /* IDSEL 0x10 */
- 0x8000 0 0 1 &mpc5200_pic 0 3 3
- 0x8000 0 0 2 &mpc5200_pic 0 3 3
- 0x8000 0 0 3 &mpc5200_pic 0 2 3
- 0x8000 0 0 4 &mpc5200_pic 0 1 3
- >;
- ranges = <0x42000000 0 0x60000000 0x60000000 0 0x10000000
- 0x02000000 0 0x90000000 0x90000000 0 0x10000000
- 0x01000000 0 0x00000000 0xa0000000 0 0x01000000>;
- };
-
- localbus {
- ranges = <0 0 0xff800000 0x00800000
- 1 0 0x80000000 0x00800000
- 3 0 0x80000000 0x00800000>;
-
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x00800000>;
- bank-width = <4>;
- device-width = <2>;
- #size-cells = <1>;
- #address-cells = <1>;
- partition@0 {
- label = "DTS";
- reg = <0x0 0x00100000>;
- };
- partition@100000 {
- label = "Kernel";
- reg = <0x100000 0x00200000>;
- };
- partition@300000 {
- label = "RootFS";
- reg = <0x00300000 0x00200000>;
- };
- partition@500000 {
- label = "user";
- reg = <0x00500000 0x00200000>;
- };
- partition@700000 {
- label = "U-Boot";
- reg = <0x00700000 0x00040000>;
- };
- partition@740000 {
- label = "Env";
- reg = <0x00740000 0x00020000>;
- };
- partition@760000 {
- label = "red. Env";
- reg = <0x00760000 0x00020000>;
- };
- partition@780000 {
- label = "reserve";
- reg = <0x00780000 0x00080000>;
- };
- };
-
- simple100: gpio-controller-100@3,600100 {
- compatible = "manroland,mucmc52-aux-gpio";
- reg = <3 0x00600100 0x1>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- simple104: gpio-controller-104@3,600104 {
- compatible = "manroland,mucmc52-aux-gpio";
- reg = <3 0x00600104 0x1>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- simple200: gpio-controller-200@3,600200 {
- compatible = "manroland,mucmc52-aux-gpio";
- reg = <3 0x00600200 0x1>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- simple201: gpio-controller-201@3,600201 {
- compatible = "manroland,mucmc52-aux-gpio";
- reg = <3 0x00600201 0x1>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- simple202: gpio-controller-202@3,600202 {
- compatible = "manroland,mucmc52-aux-gpio";
- reg = <3 0x00600202 0x1>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- simple203: gpio-controller-203@3,600203 {
- compatible = "manroland,mucmc52-aux-gpio";
- reg = <3 0x00600203 0x1>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- simple204: gpio-controller-204@3,600204 {
- compatible = "manroland,mucmc52-aux-gpio";
- reg = <3 0x00600204 0x1>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- simple206: gpio-controller-206@3,600206 {
- compatible = "manroland,mucmc52-aux-gpio";
- reg = <3 0x00600206 0x1>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- simple207: gpio-controller-207@3,600207 {
- compatible = "manroland,mucmc52-aux-gpio";
- reg = <3 0x00600207 0x1>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- simple20f: gpio-controller-20f@3,60020f {
- compatible = "manroland,mucmc52-aux-gpio";
- reg = <3 0x0060020f 0x1>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- };
-};
diff --git a/arch/powerpc/boot/dts/o2d.dts b/arch/powerpc/boot/dts/o2d.dts
deleted file mode 100644
index 24a46f65e529..000000000000
--- a/arch/powerpc/boot/dts/o2d.dts
+++ /dev/null
@@ -1,43 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * O2D Device Tree Source
- *
- * Copyright (C) 2012 DENX Software Engineering
- * Anatolij Gustschin <agust@xxxxxxx>
- */
-
-/include/ "o2d.dtsi"
-
-/ {
- model = "ifm,o2d";
- compatible = "ifm,o2d";
-
- memory {
- reg = <0x00000000 0x08000000>; // 128MB
- };
-
- localbus {
- ranges = <0 0 0xfc000000 0x02000000
- 3 0 0xe3000000 0x00100000>;
-
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x02000000>;
- bank-width = <2>;
- device-width = <2>;
- #size-cells = <1>;
- #address-cells = <1>;
-
- partition@60000 {
- label = "kernel";
- reg = <0x00060000 0x00260000>;
- read-only;
- };
- /* o2d specific partitions */
- partition@2c0000 {
- label = "o2d user defined";
- reg = <0x002c0000 0x01d40000>;
- };
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/o2d.dtsi b/arch/powerpc/boot/dts/o2d.dtsi
deleted file mode 100644
index 6661955a2be4..000000000000
--- a/arch/powerpc/boot/dts/o2d.dtsi
+++ /dev/null
@@ -1,118 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * O2D base Device Tree Source
- *
- * Copyright (C) 2012 DENX Software Engineering
- * Anatolij Gustschin <agust@xxxxxxx>
- */
-
-/include/ "mpc5200b.dtsi"
-
-&gpt0 {
- gpio-controller;
- fsl,has-wdt;
- fsl,wdt-on-boot = <0>;
-};
-&gpt1 { gpio-controller; };
-
-/ {
- model = "ifm,o2d";
- compatible = "ifm,o2d";
-
- memory {
- reg = <0x00000000 0x04000000>; // 64MB
- };
-
- soc5200@f0000000 {
-
- rtc@800 {
- status = "disabled";
- };
-
- psc@2000 { // PSC1
- compatible = "fsl,mpc5200b-psc-spi","fsl,mpc5200-psc-spi";
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
-
- spidev@0 {
- compatible = "spidev";
- spi-max-frequency = <250000>;
- reg = <0>;
- };
- };
-
- psc@2200 { // PSC2
- status = "disabled";
- };
-
- psc@2400 { // PSC3
- status = "disabled";
- };
-
- psc@2600 { // PSC4
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- psc@2800 { // PSC5
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- psc@2c00 { // PSC6
- status = "disabled";
- };
-
- ethernet@3000 {
- phy-handle = <&phy0>;
- };
-
- mdio@3000 {
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
- };
- };
-
- localbus {
- ranges = <0 0 0xff000000 0x01000000
- 3 0 0xe3000000 0x00100000>;
-
- // flash device at LocalPlus Bus CS0
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x01000000>;
- bank-width = <1>;
- device-width = <2>;
- #size-cells = <1>;
- #address-cells = <1>;
- no-unaligned-direct-access;
-
- /* common layout for all machines */
- partition@0 {
- label = "u-boot";
- reg = <0x00000000 0x00040000>;
- read-only;
- };
- partition@40000 {
- label = "env";
- reg = <0x00040000 0x00020000>;
- read-only;
- };
- };
-
- csi@3,0 {
- compatible = "ifm,o2d-csi";
- reg = <3 0 0x00100000>;
- ifm,csi-clk-handle = <&gpt7>;
- gpios = <&gpio_simple 23 0 /* imag_capture */
- &gpio_simple 26 0 /* imag_reset */
- &gpio_simple 29 0>; /* imag_master_en */
-
- interrupts = <1 1 2>; /* IRQ1, edge falling */
-
- ifm,csi-addr-bus-width = <24>;
- ifm,csi-data-bus-width = <8>;
- ifm,csi-wait-cycles = <0>;
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/o2d300.dts b/arch/powerpc/boot/dts/o2d300.dts
deleted file mode 100644
index 55a25b700bed..000000000000
--- a/arch/powerpc/boot/dts/o2d300.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * O2D300 Device Tree Source
- *
- * Copyright (C) 2012 DENX Software Engineering
- * Anatolij Gustschin <agust@xxxxxxx>
- */
-
-/include/ "o2d.dtsi"
-
-/ {
- model = "ifm,o2d300";
- compatible = "ifm,o2d";
-
- localbus {
- ranges = <0 0 0xfc000000 0x02000000
- 3 0 0xe3000000 0x00100000>;
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x02000000>;
- bank-width = <2>;
- device-width = <2>;
- #size-cells = <1>;
- #address-cells = <1>;
-
- partition@40000 {
- label = "env_1";
- reg = <0x00040000 0x00020000>;
- read-only;
- };
- partition@60000 {
- label = "env_2";
- reg = <0x00060000 0x00020000>;
- read-only;
- };
- partition@80000 {
- label = "kernel";
- reg = <0x00080000 0x00260000>;
- read-only;
- };
- /* o2d300 specific partitions */
- partition@2e0000 {
- label = "o2d300 user defined";
- reg = <0x002e0000 0x01d20000>;
- };
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/o2dnt2.dts b/arch/powerpc/boot/dts/o2dnt2.dts
deleted file mode 100644
index eeba7f5507d5..000000000000
--- a/arch/powerpc/boot/dts/o2dnt2.dts
+++ /dev/null
@@ -1,44 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * O2DNT2 Device Tree Source
- *
- * Copyright (C) 2012 DENX Software Engineering
- * Anatolij Gustschin <agust@xxxxxxx>
- */
-
-/include/ "o2d.dtsi"
-
-/ {
- model = "ifm,o2dnt2";
- compatible = "ifm,o2d";
-
- memory {
- reg = <0x00000000 0x08000000>; // 128MB
- };
-
- localbus {
- ranges = <0 0 0xfc000000 0x02000000
- 3 0 0xe3000000 0x00100000>;
-
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x02000000>;
- bank-width = <2>;
- device-width = <2>;
- #size-cells = <1>;
- #address-cells = <1>;
-
- partition@60000 {
- label = "kernel";
- reg = <0x00060000 0x00260000>;
- read-only;
- };
-
- /* o2dnt2 specific partitions */
- partition@2c0000 {
- label = "o2dnt2 user defined";
- reg = <0x002c0000 0x01d40000>;
- };
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/o2i.dts b/arch/powerpc/boot/dts/o2i.dts
deleted file mode 100644
index 3fb2e0ad7387..000000000000
--- a/arch/powerpc/boot/dts/o2i.dts
+++ /dev/null
@@ -1,29 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * O2I Device Tree Source
- *
- * Copyright (C) 2012 DENX Software Engineering
- * Anatolij Gustschin <agust@xxxxxxx>
- */
-
-/include/ "o2d.dtsi"
-
-/ {
- model = "ifm,o2i";
- compatible = "ifm,o2d";
-
- localbus {
- flash@0,0 {
- partition@60000 {
- label = "kernel";
- reg = <0x00060000 0x00260000>;
- read-only;
- };
- /* o2i specific partitions */
- partition@2c0000 {
- label = "o2i user defined";
- reg = <0x002c0000 0x00d40000>;
- };
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/o2mnt.dts b/arch/powerpc/boot/dts/o2mnt.dts
deleted file mode 100644
index c5e0ba6e8f2b..000000000000
--- a/arch/powerpc/boot/dts/o2mnt.dts
+++ /dev/null
@@ -1,29 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * O2MNT Device Tree Source
- *
- * Copyright (C) 2012 DENX Software Engineering
- * Anatolij Gustschin <agust@xxxxxxx>
- */
-
-/include/ "o2d.dtsi"
-
-/ {
- model = "ifm,o2mnt";
- compatible = "ifm,o2d";
-
- localbus {
- flash@0,0 {
- partition@60000 {
- label = "kernel";
- reg = <0x00060000 0x00260000>;
- read-only;
- };
- /* add o2mnt specific partitions */
- partition@2c0000 {
- label = "o2mnt user defined";
- reg = <0x002c0000 0x00d40000>;
- };
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/o3dnt.dts b/arch/powerpc/boot/dts/o3dnt.dts
deleted file mode 100644
index fd00396b0593..000000000000
--- a/arch/powerpc/boot/dts/o3dnt.dts
+++ /dev/null
@@ -1,44 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * O3DNT Device Tree Source
- *
- * Copyright (C) 2012 DENX Software Engineering
- * Anatolij Gustschin <agust@xxxxxxx>
- */
-
-/include/ "o2d.dtsi"
-
-/ {
- model = "ifm,o3dnt";
- compatible = "ifm,o2d";
-
- memory {
- reg = <0x00000000 0x04000000>; // 64MB
- };
-
- localbus {
- ranges = <0 0 0xfc000000 0x01000000
- 3 0 0xe3000000 0x00100000>;
-
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x01000000>;
- bank-width = <2>;
- device-width = <2>;
- #size-cells = <1>;
- #address-cells = <1>;
-
- partition@60000 {
- label = "kernel";
- reg = <0x00060000 0x00260000>;
- read-only;
- };
-
- /* o3dnt specific partitions */
- partition@2c0000 {
- label = "o3dnt user defined";
- reg = <0x002c0000 0x00d40000>;
- };
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/pcm030.dts b/arch/powerpc/boot/dts/pcm030.dts
deleted file mode 100644
index b1bc731f7afd..000000000000
--- a/arch/powerpc/boot/dts/pcm030.dts
+++ /dev/null
@@ -1,106 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * phyCORE-MPC5200B-tiny (pcm030) board Device Tree Source
- *
- * Copyright 2006 Pengutronix
- * Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
- * Copyright 2007 Pengutronix
- * Juergen Beisert <j.beisert@xxxxxxxxxxxxxx>
- */
-
-/include/ "mpc5200b.dtsi"
-
-&gpt0 { fsl,has-wdt; };
-&gpt2 { gpio-controller; };
-&gpt3 { gpio-controller; };
-&gpt4 { gpio-controller; };
-&gpt5 { gpio-controller; };
-&gpt6 { gpio-controller; };
-&gpt7 { gpio-controller; };
-
-/ {
- model = "phytec,pcm030";
- compatible = "phytec,pcm030";
-
- soc5200@f0000000 {
- audioplatform: psc@2000 { /* PSC1 in ac97 mode */
- compatible = "mpc5200b-psc-ac97","fsl,mpc5200b-psc-ac97";
- cell-index = <0>;
- };
-
- /* PSC2 port is used by CAN1/2 */
- psc@2200 {
- status = "disabled";
- };
-
- psc@2400 { /* PSC3 in UART mode */
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- /* PSC4 is ??? */
- psc@2600 {
- status = "disabled";
- };
-
- /* PSC5 is ??? */
- psc@2800 {
- status = "disabled";
- };
-
- psc@2c00 { /* PSC6 in UART mode */
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- ethernet@3000 {
- phy-handle = <&phy0>;
- };
-
- mdio@3000 {
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
- };
-
- i2c@3d40 {
- rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
- eeprom@52 {
- compatible = "catalyst,24c32", "atmel,24c32";
- reg = <0x52>;
- pagesize = <32>;
- };
- };
-
- sram@8000 {
- compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
- reg = <0x8000 0x4000>;
- };
- };
-
- pci@f0000d00 {
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
- 0xc000 0 0 2 &mpc5200_pic 1 1 3
- 0xc000 0 0 3 &mpc5200_pic 1 2 3
- 0xc000 0 0 4 &mpc5200_pic 1 3 3
-
- 0xc800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
- 0xc800 0 0 2 &mpc5200_pic 1 2 3
- 0xc800 0 0 3 &mpc5200_pic 1 3 3
- 0xc800 0 0 4 &mpc5200_pic 0 0 3>;
- ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
- 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
- 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
- };
-
- localbus {
- status = "disabled";
- };
-
- sound {
- compatible = "phytec,pcm030-audio-fabric";
- asoc-platform = <&audioplatform>;
- };
-};
diff --git a/arch/powerpc/boot/dts/pcm032.dts b/arch/powerpc/boot/dts/pcm032.dts
deleted file mode 100644
index 780e13d99e7b..000000000000
--- a/arch/powerpc/boot/dts/pcm032.dts
+++ /dev/null
@@ -1,183 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * phyCORE-MPC5200B-IO (pcm032) board Device Tree Source
- *
- * Copyright (C) 2006-2009 Pengutronix
- * Sascha Hauer, Juergen Beisert, Wolfram Sang <kernel@xxxxxxxxxxxxxx>
- */
-
-/include/ "mpc5200b.dtsi"
-
-&gpt0 { fsl,has-wdt; };
-&gpt2 { gpio-controller; };
-&gpt3 { gpio-controller; };
-&gpt4 { gpio-controller; };
-&gpt5 { gpio-controller; };
-&gpt6 { gpio-controller; };
-&gpt7 { gpio-controller; };
-
-/ {
- model = "phytec,pcm032";
- compatible = "phytec,pcm032";
-
- memory {
- reg = <0x00000000 0x08000000>; // 128MB
- };
-
- soc5200@f0000000 {
- psc@2000 { /* PSC1 is ac97 */
- compatible = "fsl,mpc5200b-psc-ac97","fsl,mpc5200-psc-ac97";
- cell-index = <0>;
- };
-
- /* PSC2 port is used by CAN1/2 */
- psc@2200 {
- status = "disabled";
- };
-
- psc@2400 { /* PSC3 in UART mode */
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- /* PSC4 is ??? */
- psc@2600 {
- status = "disabled";
- };
-
- /* PSC5 is ??? */
- psc@2800 {
- status = "disabled";
- };
-
- psc@2c00 { /* PSC6 in UART mode */
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- ethernet@3000 {
- phy-handle = <&phy0>;
- };
-
- mdio@3000 {
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
- };
-
- i2c@3d40 {
- rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
- eeprom@52 {
- compatible = "catalyst,24c32", "atmel,24c32";
- reg = <0x52>;
- pagesize = <32>;
- };
- };
- };
-
- pci@f0000d00 {
- interrupt-map-mask = <0xf800 0 0 7>;
- interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
- 0xc000 0 0 2 &mpc5200_pic 1 1 3
- 0xc000 0 0 3 &mpc5200_pic 1 2 3
- 0xc000 0 0 4 &mpc5200_pic 1 3 3
-
- 0xc800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
- 0xc800 0 0 2 &mpc5200_pic 1 2 3
- 0xc800 0 0 3 &mpc5200_pic 1 3 3
- 0xc800 0 0 4 &mpc5200_pic 0 0 3>;
- ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
- 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
- 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
- };
-
- localbus {
- ranges = <0 0 0xfe000000 0x02000000
- 1 0 0xfc000000 0x02000000
- 2 0 0xfbe00000 0x00200000
- 3 0 0xf9e00000 0x02000000
- 4 0 0xf7e00000 0x02000000
- 5 0 0xe6000000 0x02000000
- 6 0 0xe8000000 0x02000000
- 7 0 0xea000000 0x02000000>;
-
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x02000000>;
- bank-width = <4>;
- #size-cells = <1>;
- #address-cells = <1>;
-
- partition@0 {
- label = "ubootl";
- reg = <0x00000000 0x00040000>;
- };
- partition@40000 {
- label = "kernel";
- reg = <0x00040000 0x001c0000>;
- };
- partition@200000 {
- label = "jffs2";
- reg = <0x00200000 0x01d00000>;
- };
- partition@1f00000 {
- label = "uboot";
- reg = <0x01f00000 0x00040000>;
- };
- partition@1f40000 {
- label = "env";
- reg = <0x01f40000 0x00040000>;
- };
- partition@1f80000 {
- label = "oftree";
- reg = <0x01f80000 0x00040000>;
- };
- partition@1fc0000 {
- label = "space";
- reg = <0x01fc0000 0x00040000>;
- };
- };
-
- sram@2,0 {
- compatible = "mtd-ram";
- reg = <2 0 0x00200000>;
- bank-width = <2>;
- };
-
- /*
- * example snippets for FPGA
- *
- * fpga@3,0 {
- * compatible = "fpga_driver";
- * reg = <3 0 0x02000000>;
- * bank-width = <4>;
- * };
- *
- * fpga@4,0 {
- * compatible = "fpga_driver";
- * reg = <4 0 0x02000000>;
- * bank-width = <4>;
- * };
- */
-
- /*
- * example snippets for free chipselects
- *
- * device@5,0 {
- * compatible = "custom_driver";
- * reg = <5 0 0x02000000>;
- * };
- *
- * device@6,0 {
- * compatible = "custom_driver";
- * reg = <6 0 0x02000000>;
- * };
- *
- * device@7,0 {
- * compatible = "custom_driver";
- * reg = <7 0 0x02000000>;
- * };
- */
- };
-};
diff --git a/arch/powerpc/boot/dts/pdm360ng.dts b/arch/powerpc/boot/dts/pdm360ng.dts
deleted file mode 100644
index 67c3b9db75d7..000000000000
--- a/arch/powerpc/boot/dts/pdm360ng.dts
+++ /dev/null
@@ -1,195 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Device Tree Source for IFM PDM360NG.
- *
- * Copyright 2009 - 2010 DENX Software Engineering.
- * Anatolij Gustschin <agust@xxxxxxx>
- *
- * Based on MPC5121E ADS dts.
- * Copyright 2008 Freescale Semiconductor Inc.
- */
-
-#include "mpc5121.dtsi"
-
-/ {
- model = "pdm360ng";
- compatible = "ifm,pdm360ng", "fsl,mpc5121";
- #address-cells = <1>;
- #size-cells = <1>;
- interrupt-parent = <&ipic>;
-
- memory {
- device_type = "memory";
- reg = <0x00000000 0x20000000>; // 512MB at 0
- };
-
- nfc@40000000 {
- bank-width = <0x1>;
- chips = <0x1>;
-
- partition@0 {
- label = "nand0";
- reg = <0x0 0x40000000>;
- };
- };
-
- localbus@80000020 {
- ranges = <0x0 0x0 0xf0000000 0x10000000 /* Flash */
- 0x2 0x0 0x50040000 0x00020000>; /* CS2: MRAM */
-
- flash@0,0 {
- compatible = "amd,s29gl01gp", "cfi-flash";
- reg = <0 0x00000000 0x08000000
- 0 0x08000000 0x08000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- bank-width = <4>;
- device-width = <2>;
-
- partition@0 {
- label = "u-boot";
- reg = <0x00000000 0x00080000>;
- read-only;
- };
- partition@80000 {
- label = "environment";
- reg = <0x00080000 0x00080000>;
- read-only;
- };
- partition@100000 {
- label = "splash-image";
- reg = <0x00100000 0x00080000>;
- read-only;
- };
- partition@180000 {
- label = "device-tree";
- reg = <0x00180000 0x00040000>;
- };
- partition@1c0000 {
- label = "kernel";
- reg = <0x001c0000 0x00500000>;
- };
- partition@6c0000 {
- label = "filesystem";
- reg = <0x006c0000 0x07940000>;
- };
- };
-
- mram0@2,0 {
- compatible = "mtd-ram";
- reg = <2 0x00000 0x10000>;
- bank-width = <2>;
- };
-
- mram1@2,10000 {
- compatible = "mtd-ram";
- reg = <2 0x010000 0x10000>;
- bank-width = <2>;
- };
- };
-
- soc@80000000 {
-
- i2c@1700 {
- fsl,preserve-clocking;
-
- eeprom@50 {
- compatible = "atmel,24c01";
- reg = <0x50>;
- };
-
- rtc@68 {
- compatible = "st,m41t00";
- reg = <0x68>;
- };
- };
-
- i2c@1720 {
- status = "disabled";
- };
-
- i2c@1740 {
- fsl,preserve-clocking;
- };
-
- ethernet@2800 {
- phy-handle = <&phy0>;
- };
-
- mdio@2800 {
- phy0: ethernet-phy@1f {
- compatible = "smsc,lan8700";
- reg = <0x1f>;
- };
- };
-
- /* USB1 using external ULPI PHY */
- usb@3000 {
- dr_mode = "host";
- };
-
- /* USB0 using internal UTMI PHY */
- usb@4000 {
- fsl,invert-pwr-fault;
- };
-
- psc@11000 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- };
-
- psc@11100 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- };
-
- psc@11200 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- };
-
- psc@11300 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- };
-
- psc@11400 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- };
-
- psc@11500 {
- status = "disabled";
- };
-
- psc@11600 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- };
-
- psc@11700 {
- status = "disabled";
- };
-
- psc@11800 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- };
-
- psc@11900 {
- compatible = "fsl,mpc5121-psc-spi", "fsl,mpc5121-psc";
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* ADS7845 touch screen controller */
- ts@0 {
- compatible = "ti,ads7846";
- reg = <0x0>;
- spi-max-frequency = <3000000>;
- /* pen irq is GPIO25 */
- interrupts = <78 0x8>;
- };
- };
-
- psc@11a00 {
- status = "disabled";
- };
-
- psc@11b00 {
- compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
- };
- };
-};
diff --git a/arch/powerpc/boot/dts/uc101.dts b/arch/powerpc/boot/dts/uc101.dts
deleted file mode 100644
index 2e34d019178b..000000000000
--- a/arch/powerpc/boot/dts/uc101.dts
+++ /dev/null
@@ -1,152 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Manroland uc101 board Device Tree Source
- *
- * Copyright (C) 2009 DENX Software Engineering GmbH
- * Heiko Schocher <hs@xxxxxxx>
- * Copyright 2006-2007 Secret Lab Technologies Ltd.
- */
-
-/include/ "mpc5200b.dtsi"
-
-&gpt0 { gpio-controller; };
-&gpt1 { gpio-controller; };
-&gpt2 { gpio-controller; };
-&gpt3 { gpio-controller; };
-&gpt4 { gpio-controller; };
-&gpt5 { gpio-controller; };
-&gpt6 { gpio-controller; };
-&gpt7 { gpio-controller; };
-
-/ {
- model = "manroland,uc101";
- compatible = "manroland,uc101";
-
- soc5200@f0000000 {
- rtc@800 {
- status = "disabled";
- };
-
- can@900 {
- status = "disabled";
- };
-
- can@980 {
- status = "disabled";
- };
-
- spi@f00 {
- status = "disabled";
- };
-
- usb@1000 {
- status = "disabled";
- };
-
- psc@2000 { // PSC1
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- psc@2200 { // PSC2
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- psc@2400 { // PSC3
- status = "disabled";
- };
-
- psc@2600 { // PSC4
- status = "disabled";
- };
-
- psc@2800 { // PSC5
- status = "disabled";
- };
-
- psc@2c00 { // PSC6
- compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- };
-
- ethernet@3000 {
- phy-handle = <&phy0>;
- };
-
- mdio@3000 {
- phy0: ethernet-phy@0 {
- compatible = "intel,lxt971";
- reg = <0>;
- };
- };
-
- i2c@3d00 {
- status = "disabled";
- };
-
- i2c@3d40 {
- fsl,preserve-clocking;
- clock-frequency = <400000>;
-
- hwmon@2c {
- compatible = "ad,adm9240";
- reg = <0x2c>;
- };
- rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
- };
- };
-
- pci@f0000d00 {
- status = "disabled";
- };
-
- localbus {
- ranges = <0 0 0xff800000 0x00800000
- 1 0 0x80000000 0x00800000
- 3 0 0x80000000 0x00800000>;
-
- flash@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x00800000>;
- bank-width = <2>;
- device-width = <2>;
- #size-cells = <1>;
- #address-cells = <1>;
-
- partition@0 {
- label = "DTS";
- reg = <0x0 0x00100000>;
- };
- partition@100000 {
- label = "Kernel";
- reg = <0x100000 0x00200000>;
- };
- partition@300000 {
- label = "RootFS";
- reg = <0x00300000 0x00200000>;
- };
- partition@500000 {
- label = "user";
- reg = <0x00500000 0x00200000>;
- };
- partition@700000 {
- label = "U-Boot";
- reg = <0x00700000 0x00040000>;
- };
- partition@740000 {
- label = "Env";
- reg = <0x00740000 0x00010000>;
- };
- partition@750000 {
- label = "red. Env";
- reg = <0x00750000 0x00010000>;
- };
- partition@760000 {
- label = "reserve";
- reg = <0x00760000 0x000a0000>;
- };
- };
-
- };
-};
--
2.30.2
