Support for phylink_validate() and reused KSZ commmon API for
phylink_mac_link_down() operation
lan937x_phylink_mac_config configures the interface using
lan937x_mac_config and lan937x_phylink_mac_link_up configures
the speed/duplex/flow control.
Currently SGMII & in-band neg are not supported & it will be
added later.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@xxxxxxxxxxxxx>
---
drivers/net/dsa/microchip/lan937x_dev.c | 149 +++++++++++++++++++++++
drivers/net/dsa/microchip/lan937x_dev.h | 5 +
drivers/net/dsa/microchip/lan937x_main.c | 98 +++++++++++++++
3 files changed, 252 insertions(+)
diff --git a/drivers/net/dsa/microchip/lan937x_dev.c b/drivers/net/dsa/microchip/lan937x_dev.c
index 27f3aa5292f9..6a76e7223643 100644
--- a/drivers/net/dsa/microchip/lan937x_dev.c
+++ b/drivers/net/dsa/microchip/lan937x_dev.c
@@ -405,6 +405,155 @@ int lan937x_internal_phy_read(struct ksz_device *dev, int addr, int reg,
return ret;
}
+static void lan937x_config_gbit(struct ksz_device *dev, bool gbit, u8 *data)
+{
+ if (gbit)
+ *data &= ~PORT_MII_NOT_1GBIT;
+ else
+ *data |= PORT_MII_NOT_1GBIT;
+}
+
+static void lan937x_update_rgmii_delay(struct ksz_device *dev, int port,
+ bool is_tx)
+{
+ struct ksz_port *p = &dev->ports[port];
+ u16 data16;
+ int reg;
+
+ /* choose register based on tx/rx */
+ if (is_tx)
+ reg = REG_PORT_XMII_CTRL_5;
+ else
+ reg = REG_PORT_XMII_CTRL_4;
+
+ lan937x_pread16(dev, port, reg, &data16);
+
+ /* clear tune Adjust */
+ data16 &= ~PORT_TUNE_ADJ;
+
+ data16 |= (p->rgmii_tx_val << 7);
+
+ /* write tune Adjust */
+ lan937x_pwrite16(dev, port, reg, data16);
+
+ data16 |= PORT_DLL_RESET;
+
+ /* write DLL reset to take effect */
+ lan937x_pwrite16(dev, port, reg, data16);
+}
+
+static void lan937x_apply_rgmii_delay(struct ksz_device *dev, int port)
+{
+ struct ksz_port *p = &dev->ports[port];
+ u8 data8;
+
+ /* clear the bits */
+ lan937x_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
+ data8 &= ~(PORT_RGMII_ID_EG_ENABLE | PORT_RGMII_ID_IG_ENABLE);
+
+ if (p->rgmii_tx_val) {
+ lan937x_update_rgmii_delay(dev, port, true);
+ data8 |= PORT_RGMII_ID_EG_ENABLE;
+ }
+
+ if (p->rgmii_rx_val) {
+ lan937x_update_rgmii_delay(dev, port, false);
+ data8 |= PORT_RGMII_ID_IG_ENABLE;
+ }
+
+ /* Enable RGMII internal delays */
+ lan937x_pwrite8(dev, port, REG_PORT_XMII_CTRL_1, data8);
+}
+
+void lan937x_mac_config(struct ksz_device *dev, int port,
+ phy_interface_t interface)
+{
+ u8 data8;
+
+ lan937x_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
+
+ /* clear MII selection & set it based on interface later */
+ data8 &= ~PORT_MII_SEL_M;
+
+ /* configure MAC based on interface */
+ switch (interface) {
+ case PHY_INTERFACE_MODE_MII:
+ lan937x_config_gbit(dev, false, &data8);
+ data8 |= PORT_MII_SEL;
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ lan937x_config_gbit(dev, false, &data8);
+ data8 |= PORT_RMII_SEL;
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ lan937x_config_gbit(dev, true, &data8);
+ data8 |= PORT_RGMII_SEL;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ lan937x_config_gbit(dev, true, &data8);
+ data8 |= PORT_RGMII_SEL;
+
+ /* Apply rgmii internal delay for the mac */
+ lan937x_apply_rgmii_delay(dev, port);
+ break;
+ default:
+ dev_err(dev->dev, "Unsupported interface '%s' for port %d\n",
+ phy_modes(interface), port);
+ return;
+ }
+
+ /* Write the updated value */
+ lan937x_pwrite8(dev, port, REG_PORT_XMII_CTRL_1, data8);
+}
+
+void lan937x_config_interface(struct ksz_device *dev, int port,
+ int speed, int duplex,
+ bool tx_pause, bool rx_pause)
+{
+ u8 xmii_ctrl0, xmii_ctrl1;
+
+ lan937x_pread8(dev, port, REG_PORT_XMII_CTRL_0, &xmii_ctrl0);
+ lan937x_pread8(dev, port, REG_PORT_XMII_CTRL_1, &xmii_ctrl1);
+
+ switch (speed) {
+ case SPEED_1000:
+ lan937x_config_gbit(dev, true, &xmii_ctrl1);
+ break;
+ case SPEED_100:
+ lan937x_config_gbit(dev, false, &xmii_ctrl1);
+ xmii_ctrl0 |= PORT_MAC_SPEED_100;
+ break;
+ case SPEED_10:
+ lan937x_config_gbit(dev, false, &xmii_ctrl1);
+ xmii_ctrl0 &= ~PORT_MAC_SPEED_100;
+ break;
+ default:
+ dev_err(dev->dev, "Unsupported speed on port %d: %d\n",
+ port, speed);
+ return;
+ }
+
+ if (duplex)
+ xmii_ctrl0 |= PORT_FULL_DUPLEX;
+ else
+ xmii_ctrl0 &= ~PORT_FULL_DUPLEX;
+
+ if (tx_pause)
+ xmii_ctrl0 |= PORT_TX_FLOW_CTRL;
+ else
+ xmii_ctrl1 &= ~PORT_TX_FLOW_CTRL;
+
+ if (rx_pause)
+ xmii_ctrl0 |= PORT_RX_FLOW_CTRL;
+ else
+ xmii_ctrl0 &= ~PORT_RX_FLOW_CTRL;
+
+ lan937x_pwrite8(dev, port, REG_PORT_XMII_CTRL_0, xmii_ctrl0);
+ lan937x_pwrite8(dev, port, REG_PORT_XMII_CTRL_1, xmii_ctrl1);
+}
+
void lan937x_port_setup(struct ksz_device *dev, int port, bool cpu_port)
{
struct ksz_port *p = &dev->ports[port];
diff --git a/drivers/net/dsa/microchip/lan937x_dev.h b/drivers/net/dsa/microchip/lan937x_dev.h
index 9e276f317cb3..43dc8918f63e 100644
--- a/drivers/net/dsa/microchip/lan937x_dev.h
+++ b/drivers/net/dsa/microchip/lan937x_dev.h
@@ -33,6 +33,11 @@ void lan937x_cfg_port_member(struct ksz_device *dev, int port,
u8 member);
void lan937x_port_setup(struct ksz_device *dev, int port, bool cpu_port);
int lan937x_enable_spi_indirect_access(struct ksz_device *dev);
+void lan937x_config_interface(struct ksz_device *dev, int port,
+ int speed, int duplex,
+ bool tx_pause, bool rx_pause);
+void lan937x_mac_config(struct ksz_device *dev, int port,
+ phy_interface_t interface);
struct mib_names {
int index;
diff --git a/drivers/net/dsa/microchip/lan937x_main.c b/drivers/net/dsa/microchip/lan937x_main.c
index 4d64d325ff56..df29d1ed98b5 100644
--- a/drivers/net/dsa/microchip/lan937x_main.c
+++ b/drivers/net/dsa/microchip/lan937x_main.c
@@ -372,6 +372,100 @@ static int lan937x_get_max_mtu(struct dsa_switch *ds, int port)
return (FR_MAX_SIZE - VLAN_ETH_HLEN - ETH_FCS_LEN);
}
+static void lan937x_phylink_mac_config(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ const struct phylink_link_state *state)
+{
+ struct ksz_device *dev = ds->priv;
+
+ /* Internal PHYs */
+ if (lan937x_is_internal_phy_port(dev, port))
+ return;
+
+ if (phylink_autoneg_inband(mode)) {
+ dev_err(ds->dev, "In-band AN not supported!\n");
+ return;
+ }
+
+ lan937x_mac_config(dev, port, state->interface);
+}
+
+static void lan937x_phylink_mac_link_up(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface,
+ struct phy_device *phydev,
+ int speed, int duplex,
+ bool tx_pause, bool rx_pause)
+{
+ struct ksz_device *dev = ds->priv;
+
+ /* Internal PHYs */
+ if (lan937x_is_internal_phy_port(dev, port))
+ return;
+
+ if (phylink_autoneg_inband(mode)) {
+ dev_err(ds->dev, "In-band AN not supported!\n");
+ return;
+ }
+ lan937x_config_interface(dev, port, speed, duplex,
+ tx_pause, rx_pause);
+}
+
+static void lan937x_phylink_validate(struct dsa_switch *ds, int port,
+ unsigned long *supported,
+ struct phylink_link_state *state)
+{
+ struct ksz_device *dev = ds->priv;
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+ /* Check for unsupported interfaces */
+ if (!phy_interface_mode_is_rgmii(state->interface) &&
+ state->interface != PHY_INTERFACE_MODE_RMII &&
+ state->interface != PHY_INTERFACE_MODE_MII &&
+ state->interface != PHY_INTERFACE_MODE_NA &&
+ state->interface != PHY_INTERFACE_MODE_INTERNAL) {
+ bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+ dev_err(ds->dev, "Unsupported interface '%s' for port %d\n",
+ phy_modes(state->interface), port);
+ return;
+ }
+
+ /* For RGMII, RMII, MII and internal TX phy port and
+ * as per phylink.h, when @state->interface is %PHY_INTERFACE_MODE_NA,
+ * phylink expects the MAC driver to return all supported link modes.
+ */
+ if (phy_interface_mode_is_rgmii(state->interface) ||
+ state->interface == PHY_INTERFACE_MODE_RMII ||
+ state->interface == PHY_INTERFACE_MODE_MII ||
+ state->interface == PHY_INTERFACE_MODE_NA ||
+ lan937x_is_internal_base_tx_phy_port(dev, port)) {
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+ phylink_set(mask, Autoneg);
+ phylink_set_port_modes(mask);
+ phylink_set(mask, Pause);
+ phylink_set(mask, Asym_Pause);
+ }
+
+ /* For RGMII interface */
+ if (phy_interface_mode_is_rgmii(state->interface) ||
+ state->interface == PHY_INTERFACE_MODE_NA)
+ phylink_set(mask, 1000baseT_Full);
+
+ /* For T1 PHY */
+ if (lan937x_is_internal_base_t1_phy_port(dev, port) ||
+ state->interface == PHY_INTERFACE_MODE_NA) {
+ phylink_set(mask, 100baseT1_Full);
+ phylink_set_port_modes(mask);
+ }
+
+ bitmap_and(supported, supported, mask, __ETHTOOL_LINK_MODE_MASK_NBITS);
+ bitmap_and(state->advertising, state->advertising, mask,
+ __ETHTOOL_LINK_MODE_MASK_NBITS);
+}
+
const struct dsa_switch_ops lan937x_switch_ops = {
.get_tag_protocol = lan937x_get_tag_protocol,
.setup = lan937x_setup,
@@ -384,6 +478,10 @@ const struct dsa_switch_ops lan937x_switch_ops = {
.port_fast_age = ksz_port_fast_age,
.port_max_mtu = lan937x_get_max_mtu,
.port_change_mtu = lan937x_change_mtu,
+ .phylink_validate = lan937x_phylink_validate,
+ .phylink_mac_link_down = ksz_mac_link_down,
+ .phylink_mac_config = lan937x_phylink_mac_config,
+ .phylink_mac_link_up = lan937x_phylink_mac_link_up,
};
int lan937x_switch_register(struct ksz_device *dev)
--
2.27.0
