Add entries from Documentation/ABI/testing/sysfs-bus-iio-scd30 to Documentation/ABI/testing/sysfs-bus-iio. The attributes of the scd4x and scd30 are common. Remove Documentation/ABI/testing/sysfs-bus-iio-scd30. Signed-off-by: Roan van Dijk <roan@xxxxxxxxxxx> --- Documentation/ABI/testing/sysfs-bus-iio | 41 +++++++++++++++++++ Documentation/ABI/testing/sysfs-bus-iio-scd30 | 34 --------------- 2 files changed, 41 insertions(+), 34 deletions(-) delete mode 100644 Documentation/ABI/testing/sysfs-bus-iio-scd30 diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index 6ad47a67521c..c27347d3608e 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -1957,3 +1957,44 @@ Description: Specify the percent for light sensor relative to the channel absolute value that a data field should change before an event is generated. Units are a percentage of the prior reading. + +What: /sys/bus/iio/devices/iio:deviceX/calibration_auto_enable +Date: June 2020 +KernelVersion: 5.8 +Contact: linux-iio@xxxxxxxxxxxxxxx +Description: + Some sensors have the ability to apply auto calibration at + runtime. For example, it may be necessary to compensate for + contaminant build-up in a measurement chamber or optical + element deterioration that would otherwise lead to sensor drift. + + Writing 1 or 0 to this attribute will respectively activate or + deactivate this auto calibration function. + + Upon reading, the current status is returned. + +What: /sys/bus/iio/devices/iio:deviceX/calibration_forced_value +Date: June 2020 +KernelVersion: 5.8 +Contact: linux-iio@xxxxxxxxxxxxxxx +Description: + Some sensors have the ability to apply a manual calibration using + a known measurement value, perhaps obtained from an external + reference device. + + Writing a value to this function will force such a calibration + change. For the scd30 the value should be from the range + [400 1 2000]. + + Note for the scd30 that a valid value may only be obtained once + it is has been written. Until then any read back of this value + should be ignored. As for the scd4x an error will be returned + immediately if the manual calibration has failed. + +What: /sys/bus/iio/devices/iio:deviceX/calibration_forced_value_available +KernelVersion: 5.15 +Contact: linux-iio@xxxxxxxxxxxxxxx +Description: + Available range for the forced calibration value, expressed as: + + - a range specified as "[min step max]" diff --git a/Documentation/ABI/testing/sysfs-bus-iio-scd30 b/Documentation/ABI/testing/sysfs-bus-iio-scd30 deleted file mode 100644 index b9712f390bec..000000000000 --- a/Documentation/ABI/testing/sysfs-bus-iio-scd30 +++ /dev/null @@ -1,34 +0,0 @@ -What: /sys/bus/iio/devices/iio:deviceX/calibration_auto_enable -Date: June 2020 -KernelVersion: 5.8 -Contact: linux-iio@xxxxxxxxxxxxxxx -Description: - Contaminants build-up in the measurement chamber or optical - elements deterioration leads to sensor drift. - - One can compensate for sensor drift by using automatic self - calibration procedure (asc). - - Writing 1 or 0 to this attribute will respectively activate or - deactivate asc. - - Upon reading current asc status is returned. - -What: /sys/bus/iio/devices/iio:deviceX/calibration_forced_value -Date: June 2020 -KernelVersion: 5.8 -Contact: linux-iio@xxxxxxxxxxxxxxx -Description: - Contaminants build-up in the measurement chamber or optical - elements deterioration leads to sensor drift. - - One can compensate for sensor drift by using forced - recalibration (frc). This is useful in case there's known - co2 reference available nearby the sensor. - - Picking value from the range [400 1 2000] and writing it to the - sensor will set frc. - - Upon reading current frc value is returned. Note that after - power cycling default value (i.e 400) is returned even though - internally sensor had recalibrated itself. -- 2.30.2
