Globalscale MOCHAbin is a Armada 7040 based development board.
Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element
Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.
Signed-off-by: Robert Marko <robert.marko@xxxxxxxxxx>
Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
---
Changes in v4:
* Rename the "u-boot" partition to "firmware" which is more appropriate
as it a concatenation of mv-ddr + TF-A + U-boot
Changes in v3:
* Use IRQ_TYPE_LEVEL_LOW instead of IRQ_TYPE_EDGE_FALLING as both the
PCA9554 and Topaz switch have an active LOW IRQ signal.
Changes in v2:
* Use "10gbase-r" instead of "10gbase-kr"
---
arch/arm64/boot/dts/marvell/Makefile | 1 +
.../boot/dts/marvell/armada-7040-mochabin.dts | 452 ++++++++++++++++++
2 files changed, 453 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 34efe0fb6f37..4d3a2ae9adbd 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-mochabin.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
diff --git a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
new file mode 100644
index 000000000000..edd0df5e9ffd
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
@@ -0,0 +1,452 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree file for Globalscale MOCHAbin
+ * Copyright (C) 2019 Globalscale technologies, Inc.
+ * Copyright (C) 2021 Sartura Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-7040.dtsi"
+
+/ {
+ model = "Globalscale MOCHAbin";
+ compatible = "globalscale,mochabin", "marvell,armada7040",
+ "marvell,armada-ap806-quad", "marvell,armada-ap806";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ ethernet0 = &cp0_eth0;
+ ethernet1 = &cp0_eth1;
+ ethernet2 = &cp0_eth2;
+ ethernet3 = &swport1;
+ ethernet4 = &swport2;
+ ethernet5 = &swport3;
+ ethernet6 = &swport4;
+ };
+
+ /* SFP+ 10G */
+ sfp_eth0: sfp-eth0 {
+ compatible = "sff,sfp";
+ i2c-bus = <&cp0_i2c1>;
+ los-gpio = <&sfp_gpio 3 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&sfp_gpio 2 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&sfp_gpio 1 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&sfp_gpio 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* SFP 1G */
+ sfp_eth2: sfp-eth2 {
+ compatible = "sff,sfp";
+ i2c-bus = <&cp0_i2c0>;
+ los-gpio = <&sfp_gpio 7 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&sfp_gpio 6 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&sfp_gpio 5 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&sfp_gpio 4 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* microUSB UART console */
+&uart0 {
+ status = "okay";
+
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+};
+
+/* eMMC */
+&ap_sdhci0 {
+ status = "okay";
+
+ bus-width = <4>;
+ non-removable;
+ /delete-property/ marvell,xenon-phy-slow-mode;
+ no-1-8-v;
+};
+
+&cp0_pinctrl {
+ cp0_uart0_pins: cp0-uart0-pins {
+ marvell,pins = "mpp6", "mpp7";
+ marvell,function = "uart0";
+ };
+
+ cp0_spi0_pins: cp0-spi0-pins {
+ marvell,pins = "mpp56", "mpp57", "mpp58", "mpp59";
+ marvell,function = "spi0";
+ };
+
+ cp0_spi1_pins: cp0-spi1-pins {
+ marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+ marvell,function = "spi1";
+ };
+
+ cp0_i2c0_pins: cp0-i2c0-pins {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "i2c0";
+ };
+
+ cp0_i2c1_pins: cp0-i2c1-pins {
+ marvell,pins = "mpp2", "mpp3";
+ marvell,function = "i2c1";
+ };
+
+ pca9554_int_pins: pca9554-int-pins {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+
+ cp0_rgmii1_pins: cp0-rgmii1-pins {
+ marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47", "mpp48", "mpp49",
+ "mpp50", "mpp51", "mpp52", "mpp53", "mpp54", "mpp55";
+ marvell,function = "ge1";
+ };
+
+ is31_sdb_pins: is31-sdb-pins {
+ marvell,pins = "mpp30";
+ marvell,function = "gpio";
+ };
+
+ cp0_pcie_reset_pins: cp0-pcie-reset-pins {
+ marvell,pins = "mpp9";
+ marvell,function = "gpio";
+ };
+
+ cp0_switch_pins: cp0-switch-pins {
+ marvell,pins = "mpp0", "mpp1";
+ marvell,function = "gpio";
+ };
+
+ cp0_phy_pins: cp0-phy-pins {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+};
+
+/* mikroBUS UART */
+&cp0_uart0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_uart0_pins>;
+};
+
+/* mikroBUS SPI */
+&cp0_spi0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_spi0_pins>;
+};
+
+/* SPI-NOR */
+&cp0_spi1{
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_spi1_pins>;
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "firmware";
+ reg = <0x0 0x3e0000>;
+ read-only;
+ };
+
+ partition@3e0000 {
+ label = "hw-info";
+ reg = <0x3e0000 0x10000>;
+ read-only;
+ };
+
+ partition@3f0000 {
+ label = "u-boot-env";
+ reg = <0x3f0000 0x10000>;
+ };
+ };
+ };
+};
+
+/* mikroBUS, 1G SFP and GPIO expander */
+&cp0_i2c0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c0_pins>;
+ clock-frequency = <100000>;
+
+ sfp_gpio: pca9554@39 {
+ compatible = "nxp,pca9554";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pca9554_int_pins>;
+ reg = <0x39>;
+
+ interrupt-parent = <&cp0_gpio1>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ /*
+ * IO0_0: SFP+_TX_FAULT
+ * IO0_1: SFP+_TX_DISABLE
+ * IO0_2: SFP+_PRSNT
+ * IO0_3: SFP+_LOSS
+ * IO0_4: SFP_TX_FAULT
+ * IO0_5: SFP_TX_DISABLE
+ * IO0_6: SFP_PRSNT
+ * IO0_7: SFP_LOSS
+ */
+ };
+};
+
+/* IS31FL3199, mini-PCIe and 10G SFP+ */
+&cp0_i2c1 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c1_pins>;
+ clock-frequency = <100000>;
+
+ leds@64 {
+ compatible = "issi,is31fl3199";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&is31_sdb_pins>;
+ shutdown-gpios = <&cp0_gpio1 30 GPIO_ACTIVE_HIGH>;
+ reg = <0x64>;
+
+ led1_red: led@1 {
+ label = "led1:red";
+ reg = <1>;
+ led-max-microamp = <20000>;
+ };
+
+ led1_green: led@2 {
+ label = "led1:green";
+ reg = <2>;
+ };
+
+ led1_blue: led@3 {
+ label = "led1:blue";
+ reg = <3>;
+ };
+
+ led2_red: led@4 {
+ label = "led2:red";
+ reg = <4>;
+ };
+
+ led2_green: led@5 {
+ label = "led2:green";
+ reg = <5>;
+ };
+
+ led2_blue: led@6 {
+ label = "led2:blue";
+ reg = <6>;
+ };
+
+ led3_red: led@7 {
+ label = "led3:red";
+ reg = <7>;
+ };
+
+ led3_green: led@8 {
+ label = "led3:green";
+ reg = <8>;
+ };
+
+ led3_blue: led@9 {
+ label = "led3:blue";
+ reg = <9>;
+ };
+ };
+};
+
+&cp0_mdio {
+ status = "okay";
+
+ /* 88E1512 PHY */
+ eth2phy: ethernet-phy@1 {
+ reg = <1>;
+ sfp = <&sfp_eth2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_phy_pins>;
+ reset-gpios = <&cp0_gpio1 12 GPIO_ACTIVE_LOW>;
+ };
+
+ /* 88E6141 Topaz switch */
+ switch: switch@3 {
+ compatible = "marvell,mv88e6085";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_switch_pins>;
+ reset-gpios = <&cp0_gpio1 0 GPIO_ACTIVE_LOW>;
+
+ interrupt-parent = <&cp0_gpio1>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ swport1: port@1 {
+ reg = <1>;
+ label = "lan0";
+ phy-handle = <&swphy1>;
+ };
+
+ swport2: port@2 {
+ reg = <2>;
+ label = "lan1";
+ phy-handle = <&swphy2>;
+ };
+
+ swport3: port@3 {
+ reg = <3>;
+ label = "lan2";
+ phy-handle = <&swphy3>;
+ };
+
+ swport4: port@4 {
+ reg = <4>;
+ label = "lan3";
+ phy-handle = <&swphy4>;
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&cp0_eth1>;
+ phy-mode = "2500base-x";
+ managed = "in-band-status";
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ swphy1: swphy1@17 {
+ reg = <17>;
+ };
+
+ swphy2: swphy2@18 {
+ reg = <18>;
+ };
+
+ swphy3: swphy3@19 {
+ reg = <19>;
+ };
+
+ swphy4: swphy4@20 {
+ reg = <20>;
+ };
+ };
+ };
+};
+
+&cp0_ethernet {
+ status = "okay";
+};
+
+/* 10G SFP+ */
+&cp0_eth0 {
+ status = "okay";
+
+ phy-mode = "10gbase-r";
+ phys = <&cp0_comphy4 0>;
+ managed = "in-band-status";
+ sfp = <&sfp_eth0>;
+};
+
+/* Topaz switch uplink */
+&cp0_eth1 {
+ status = "okay";
+
+ phy-mode = "2500base-x";
+ phys = <&cp0_comphy0 1>;
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ };
+};
+
+/* 1G SFP or 1G RJ45 */
+&cp0_eth2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_rgmii1_pins>;
+
+ phy = <ð2phy>;
+ phy-mode = "rgmii-id";
+};
+
+&cp0_utmi {
+ status = "okay";
+};
+
+/* SMSC USB5434B hub */
+&cp0_usb3_0 {
+ status = "okay";
+
+ phys = <&cp0_comphy1 0>, <&cp0_utmi0>;
+ phy-names = "cp0-usb3h0-comphy", "utmi";
+};
+
+/* miniPCI-E USB */
+&cp0_usb3_1 {
+ status = "okay";
+};
+
+&cp0_sata0 {
+ status = "okay";
+
+ /* 7 + 12 SATA connector (J24) */
+ sata-port@0 {
+ phys = <&cp0_comphy2 0>;
+ phy-names = "cp0-sata0-0-phy";
+ };
+
+ /* M.2-2250 B-key (J39) */
+ sata-port@1 {
+ phys = <&cp0_comphy3 1>;
+ phy-names = "cp0-sata0-1-phy";
+ };
+};
+
+/* miniPCI-E (J5) */
+&cp0_pcie2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_pcie_reset_pins>;
+ phys = <&cp0_comphy5 2>;
+ phy-names = "cp0-pcie2-x1-phy";
+ reset-gpio = <&cp0_gpio1 9 GPIO_ACTIVE_LOW>;
+};
--
2.31.1
