On 08/07/2014 11:29 AM, Peter Hurley wrote:
On 05/01/2014 03:04 PM, Murali Karicheri wrote:
8250 uart driver currently supports only software assisted hw flow
control. The software assisted hw flow control maintains a hw_stopped
flag in the tty structure to stop and start transmission and use modem
status interrupt for the event to drive the handshake signals. This is
not needed if hw has flow control capabilities. This patch adds a
DT attribute for enabling hw flow control for a uart port. Also skip
stop and start if this flag is present in flag field of the port
structure.
Signed-off-by: Murali Karicheri<m-karicheri2@xxxxxx>
CC: Rob Herring<robh+dt@xxxxxxxxxx>
CC: Pawel Moll<pawel.moll@xxxxxxx>
CC: Mark Rutland<mark.rutland@xxxxxxx>
CC: Ian Campbell<ijc+devicetree@xxxxxxxxxxxxxx>
CC: Kumar Gala<galak@xxxxxxxxxxxxxx>
CC: Randy Dunlap<rdunlap@xxxxxxxxxxxxx>
CC: Greg Kroah-Hartman<gregkh@xxxxxxxxxxxxxxxxxxx>
CC: Jiri Slaby<jslaby@xxxxxxx>
CC: Santosh Shilimkar<santosh.shilimkar@xxxxxx>
---
.../devicetree/bindings/serial/of-serial.txt | 1 +
drivers/tty/serial/8250/8250_core.c | 6 ++++--
drivers/tty/serial/of_serial.c | 4 ++++
drivers/tty/serial/serial_core.c | 12 +++++++++---
4 files changed, 18 insertions(+), 5 deletions(-)
[...]
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index b68550d..851707a 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -174,8 +174,12 @@ static int uart_port_startup(struct tty_struct *tty, struct uart_state *state,
if (tty->termios.c_cflag& CBAUD)
uart_set_mctrl(uport, TIOCM_RTS | TIOCM_DTR);
}
-
- if (tty_port_cts_enabled(port)) {
+ /*
+ * if hw support flow control without software intervention,
+ * then skip the below check
+ */
+ if (tty_port_cts_enabled(port)&&
+ !(uport->flags& UPF_HARD_FLOW)) {
spin_lock_irq(&uport->lock);
if (!(uport->ops->get_mctrl(uport)& TIOCM_CTS))
tty->hw_stopped = 1;
@@ -2772,7 +2776,9 @@ void uart_handle_cts_change(struct uart_port *uport, unsigned int status)
uport->icount.cts++;
- if (tty_port_cts_enabled(port)) {
+ /* skip below code if the hw flow control is supported */
+ if (tty_port_cts_enabled(port)&&
+ !(uport->flags& UPF_HARD_FLOW)) {
Why is a modem status interrupt being generated for DCTS
if autoflow control is enabled?
This should be:
WARN_ON_ONCE(uport->flags& UPF_HARD_FLOW);
to indicate a mis-configured driver/device.
This patch is already merged to the upstream branch and if you see any
issue, please
post a patch for review.
Murali
if (tty->hw_stopped) {
if (status) {
tty->hw_stopped = 0;
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
