Re: [PATCH v8 16/22] ASoC: qdsp6: audioreach: add module configuration command helpers

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 27/09/2021 17:16, Pierre-Louis Bossart wrote:

+static int audioreach_shmem_set_media_format(struct q6apm_graph *graph,
+					     struct audioreach_module *module,
+					     struct audioreach_module_config *mcfg)
+{
+	uint32_t num_channels = mcfg->num_channels;
+	struct apm_module_param_data *param_data;
+	struct payload_media_fmt_pcm *cfg;
+	struct media_format *header;
+	int rc, payload_size;
+	struct gpr_pkt *pkt;
+	void *p;
+
+	if (num_channels > 2) {
+		dev_err(graph->dev, "Error: Invalid channels (%d)!\n", num_channels);
+		return -EINVAL;
+	}

so here mcfg->num_channels > 2 is flagged as an error, but ...

+
+	payload_size = APM_SHMEM_FMT_CFG_PSIZE(num_channels) + APM_MODULE_PARAM_DATA_SIZE;
+
+	pkt = audioreach_alloc_cmd_pkt(payload_size, APM_CMD_SET_CFG, 0,
+				     graph->port->id, module->instance_id);
+	if (IS_ERR(pkt))
+		return PTR_ERR(pkt);
+
+	p = (void *)pkt + GPR_HDR_SIZE + APM_CMD_HDR_SIZE;
+
+	param_data = p;
+	param_data->module_instance_id = module->instance_id;
+	param_data->error_code = 0;
+	param_data->param_id = PARAM_ID_MEDIA_FORMAT;
+	param_data->param_size = payload_size - APM_MODULE_PARAM_DATA_SIZE;
+	p = p + APM_MODULE_PARAM_DATA_SIZE;
+
+	header = p;
+	header->data_format = DATA_FORMAT_FIXED_POINT;
+	header->fmt_id = MEDIA_FMT_ID_PCM;
+	header->payload_size = payload_size - sizeof(*header);
+
+	p = p + sizeof(*header);
+	cfg = p;
+	cfg->sample_rate = mcfg->sample_rate;
+	cfg->bit_width = mcfg->bit_width;
+	cfg->alignment = PCM_LSB_ALIGNED;
+	cfg->bits_per_sample = mcfg->bit_width;
+	cfg->q_factor = mcfg->bit_width - 1;
+	cfg->endianness = PCM_LITTLE_ENDIAN;
+	cfg->num_channels = mcfg->num_channels;
+
+	if (mcfg->num_channels == 1) {
+		cfg->channel_mapping[0] =  PCM_CHANNEL_L;
+	} else if (num_channels == 2) {
+		cfg->channel_mapping[0] =  PCM_CHANNEL_L;
+		cfg->channel_mapping[1] =  PCM_CHANNEL_R;
+	} else {
+		dev_err(graph->dev, "Error: Invalid channels (%d)!\n", num_channels);
+		rc = -EINVAL;
+		goto err;

... this is again the case where mcfg->num_channels > 2 so this block is
never executed.

I agree this else is dead code, will remove this.

--srini

+	}
+
+	rc = audioreach_graph_send_cmd_sync(graph, pkt, 0);
+err:
+	kfree(pkt);
+
+	return rc;
+}
+



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux