Le mar. 14 sept. 2021 à 21:57, Alexandre Belloni <alexandre.belloni@xxxxxxxxxxx> a écrit : > > On 14/09/2021 19:20:56+0200, Romain Perier wrote: > > Hi, > > > > ping, > > > > Well, this was sent to close from the merge window and the merge window > just closed :) Ah right, I have forgotten that, my bad ^^. Ignore my comment then Romain > > > Regards, > > Romain > > > > Le lun. 23 août 2021 à 19:16, Romain Perier <romain.perier@xxxxxxxxx> a écrit : > > > > > > This patches series adds a new driver for the RTC found in the Mstar > > > MSC313e SoCs and newer. It adds a basic rtc driver, the corresponding > > > devicetree bindings and its documentation. > > > > > > The rtctest (from selftests) has been passed on this driver, with the > > > following output: > > > $ rtctest > > > TAP version 13 > > > 1..7 > > > # Starting 7 tests from 2 test cases. > > > # RUN rtc.date_read ... > > > # rtctest.c:47:date_read:Current RTC date/time is 01/01/1970 00:02:03. > > > # OK rtc.date_read > > > ok 1 rtc.date_read > > > # RUN rtc.uie_read ... > > > # OK rtc.uie_read > > > ok 2 rtc.uie_read > > > # RUN rtc.uie_select ... > > > # OK rtc.uie_select > > > ok 3 rtc.uie_select > > > # RUN rtc.alarm_alm_set ... > > > # rtctest.c:136:alarm_alm_set:Alarm time now set to 00:02:12. > > > # rtctest.c:156:alarm_alm_set:data: 1a0 > > > # OK rtc.alarm_alm_set > > > ok 4 rtc.alarm_alm_set > > > # RUN rtc.alarm_wkalm_set ... > > > # rtctest.c:192:alarm_wkalm_set:Alarm time now set to 01/01/1970 00:02:15. > > > # OK rtc.alarm_wkalm_set > > > ok 5 rtc.alarm_wkalm_set > > > # RUN rtc.alarm_alm_set_minute ... > > > # rtctest.c:238:alarm_alm_set_minute:Alarm time now set to 00:03:00. > > > # rtctest.c:258:alarm_alm_set_minute:data: 1a0 > > > # OK rtc.alarm_alm_set_minute > > > ok 6 [ 180.545015] random: fast init done > > > rtc.alarm_alm_set_minute > > > # RUN rtc.alarm_wkalm_set_minute ... > > > # rtctest.c:294:alarm_wkalm_set_minute:Alarm time now set to 01/01/1970 00:04:00. > > > # OK rtc.alarm_wkalm_set_minute > > > ok 7 rtc.alarm_wkalm_set_minute > > > # PASSED: 7 / 7 tests passed. > > > # Totals: pass:7 fail:0 xfail:0 xpass:0 skip:0 error:0 > > > > > > Changes since v3: > > > - Fixed bad device table in MODULE_DEVICE_TABLE() > > > - Use reverse christmas tree ordering for local variables in the probe() > > > function > > > - Removed the "clk" field from the msc313_rtc data structure (not > > > required, only used in the probe function) > > > > > > Changes since v2: > > > - Added dual-license header to the dt-bindings documentation > > > - Reordered dts entries, so the rtc device_node is before the watchdog > > > device_node (because it has a lower address) > > > - Updated rtc range_max to U32_MAX > > > - Leave range_min to 0 (default value when it is not set at all) > > > - Fixed the CNT_EN_BIT logic, so .read_time will only read the time when > > > the RTC has been previously set and has a valid state (which is not > > > the case after a POR). > > > > > > Changes since v1: > > > - Fixed the DT bindings documentation and fixed dt_binding_check (an > > > include was missing) > > > - Added || COMPILE_TEST to kconfig > > > - Removed rtc_valid_tm from msc313_rtc_read_time() > > > - Removed the last write of the msc313_rtc_set_time() function (not > > > required) and improved comments > > > - Replaced the relaxed io by normal io in msc313_rtc_interrupt() > > > - Added checks to be sure that the alarm fired in msc313_rtc_interrupt() > > > - Removed msc313_rtc_remove() (replaced by devm_add_action_or_reset) > > > - Removed unnecessary software reset of the IP in the probe function > > > (the soft reset is never executed, it is a mistake from the initial > > > refactoring) > > > - Switched to devm_rtc_allocate_device() and devm_rtc_register_device(), > > > and dropped the error message related to the rtc device allocation > > > - Added an RTC range by setting .range_min and .range_max > > > - Added the "start-year" property to the DT bindings documentation > > > > > > Daniel Palmer (1): > > > rtc: Add support for the MSTAR MSC313 RTC > > > > > > Romain Perier (2): > > > dt-bindings: rtc: Add Mstar MSC313e RTC devicetree bindings > > > documentation > > > ARM: dts: mstar: Add rtc device node > > > > > > .../bindings/rtc/mstar,msc313-rtc.yaml | 49 ++++ > > > MAINTAINERS | 1 + > > > arch/arm/boot/dts/mstar-v7.dtsi | 8 + > > > drivers/rtc/Kconfig | 10 + > > > drivers/rtc/Makefile | 1 + > > > drivers/rtc/rtc-msc313.c | 258 ++++++++++++++++++ > > > 6 files changed, 327 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/rtc/mstar,msc313-rtc.yaml > > > create mode 100644 drivers/rtc/rtc-msc313.c > > > > > > -- > > > 2.30.2 > > > > > -- > Alexandre Belloni, co-owner and COO, Bootlin > Embedded Linux and Kernel engineering > https://bootlin.com
