This commit introduces support for the Sony Yoshino platform, using
the MSM8998 SoC, including:
- Sony Xperia XZ1 (codename Poplar),
- Sony Xperia XZ1 Compact (codename Lilac),
- Sony Xperia XZ Premium (codename Maple).
All of the three aforementioned smartphones are sharing a 99%
equal board configuration, with very small differences between
each other, which is the reason for the introduction of a common
msm8998-sony-xperia-yoshino DT.
This base configuration includes regulators and project-wide pin
configurations and it's made to boot to a serial console.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxxx>
Reviewed-by: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/Makefile | 3 +
.../msm8998-sony-xperia-yoshino-lilac.dts | 19 +
.../msm8998-sony-xperia-yoshino-maple.dts | 43 ++
.../msm8998-sony-xperia-yoshino-poplar.dts | 24 +
.../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 481 ++++++++++++++++++
5 files changed, 570 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 70516508be56..8a0b558c3065 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -39,6 +39,9 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-lenovo-miix-630.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-cheeseburger.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-lilac.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
new file mode 100644
index 000000000000..550de79e0151
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@xxxxxxxxxxxxxx>
+ */
+
+/dts-v1/;
+
+#include "msm8998-sony-xperia-yoshino.dtsi"
+
+/ {
+ model = "Sony Xperia XZ1 Compact";
+ compatible = "sony,xperia-lilac", "qcom,msm8998";
+};
+
+&vreg_l22a_2p85 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
new file mode 100644
index 000000000000..35a6cdb55aec
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@xxxxxxxxxxxxxx>
+ */
+
+/dts-v1/;
+
+#include "msm8998-sony-xperia-yoshino.dtsi"
+
+/ {
+ model = "Sony Xperia XZ Premium";
+ compatible = "sony,xperia-maple", "qcom,msm8998";
+
+ disp_dvdd_vreg: disp-dvdd-vreg {
+ compatible = "regulator-fixed";
+ regulator-name = "disp_dvdd_en";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ startup-delay-us = <0>;
+ enable-active-high;
+ gpio = <&pmi8998_gpio 10 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&disp_dvdd_en>;
+ };
+};
+
+&pmi8998_gpio {
+ disp_dvdd_en: disp-dvdd-en-active {
+ pins = "gpio10";
+ function = "normal";
+ bias-disable;
+ drive-push-pull;
+ output-high;
+ power-source = <0>;
+ qcom,drive-strength = <1>;
+ };
+};
+
+&vreg_l22a_2p85 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
new file mode 100644
index 000000000000..6255004b9a09
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@xxxxxxxxxxxxxx>
+ */
+
+/dts-v1/;
+
+#include "msm8998-sony-xperia-yoshino.dtsi"
+
+/ {
+ model = "Sony Xperia XZ1";
+ compatible = "sony,xperia-poplar", "qcom,msm8998";
+};
+
+&vreg_l18a_2p85 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+};
+
+&vreg_l22a_2p85 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
new file mode 100644
index 000000000000..b07cbc759807
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -0,0 +1,481 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@xxxxxxxxxxxxxx>
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxx>
+ */
+
+#include "msm8998.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+
+/ {
+ /* required for bootloader to select correct board */
+ qcom,msm-id = <0x124 0x20000>, <0x124 0x20001>; /* 8998v2, v2.1 */
+ qcom,board-id = <8 0>;
+
+ board_vbat: vbat-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VBAT";
+
+ regulator-min-microvolt = <4000000>;
+ regulator-max-microvolt = <4000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ input-name = "gpio-keys";
+ label = "Side buttons";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vol_down_pin_a>, <&cam_focus_pin_a>,
+ <&cam_snapshot_pin_a>;
+ vol-down {
+ label = "Volume Down";
+ gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ gpio-key,wakeup;
+ debounce-interval = <15>;
+ };
+
+ camera-snapshot {
+ label = "Camera Snapshot";
+ gpios = <&pm8998_gpio 7 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_CAMERA>;
+ debounce-interval = <15>;
+ };
+
+ camera-focus {
+ label = "Camera Focus";
+ gpios = <&pm8998_gpio 8 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_CAMERA_FOCUS>;
+ debounce-interval = <15>;
+ };
+ };
+
+ gpio_hall_sensor {
+ compatible = "gpio-keys";
+ input-name = "hall-sensors";
+ label = "Hall sensors";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hall_sensor0_default>;
+
+ hall_sensor0 {
+ label = "Cover Hall Sensor";
+ gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ gpio-key,wakeup;
+ debounce-interval = <30>;
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ hyp_mem: memory@85800000 {
+ reg = <0x0 0x85800000 0x0 0x3700000>;
+ no-map;
+ };
+
+ cont_splash_mem: cont-splash-region@9d400000 {
+ reg = <0x0 0x9d400000 0x0 0x2400000>;
+ no-map;
+ };
+
+ zap_shader_region: gpu@f6400000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0xf6400000 0x0 0x2000>;
+ no-map;
+ };
+
+ adsp_region: memory@fe000000 {
+ reg = <0x0 0xfe000000 0x0 0x800000>;
+ no-map;
+ };
+
+ qseecom_region: memory@fe800000 {
+ reg = <0x0 0xfe800000 0x0 0x1400000>;
+ no-map;
+ };
+
+ ramoops@ffc00000 {
+ compatible = "ramoops";
+ reg = <0x0 0xffc00000 0x0 0x100000>;
+ record-size = <0x10000>;
+ console-size = <0x60000>;
+ ftrace-size = <0x10000>;
+ pmsg-size = <0x20000>;
+ ecc-size = <16>;
+ };
+ };
+};
+
+&blsp2_uart1 {
+ status = "okay";
+};
+
+&mmcc {
+ status = "ok";
+};
+
+&mmss_smmu {
+ status = "ok";
+};
+
+&pm8005_lsid1 {
+ pm8005-regulators {
+ compatible = "qcom,pm8005-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+
+ /* VDD_GFX supply */
+ pm8005_s1: s1 {
+ regulator-min-microvolt = <524000>;
+ regulator-max-microvolt = <1088000>;
+ regulator-enable-ramp-delay = <500>;
+
+ regulator-always-on;
+ };
+ };
+};
+
+&pm8998_gpio {
+ vol_down_pin_a: vol-down-active {
+ pins = "gpio5";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ bias-pull-up;
+ input-enable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+
+ cam_focus_pin_a: cam-focus-btn-active {
+ pins = "gpio7";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ bias-pull-up;
+ input-enable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+
+ cam_snapshot_pin_a: cam-snapshot-btn-active {
+ pins = "gpio8";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ bias-pull-up;
+ input-enable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+};
+
+&pm8998_pon {
+ resin {
+ compatible = "pm8941-resin";
+ interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+};
+
+&qusb2phy {
+ status = "okay";
+
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&rpm_requests {
+ pm8998-regulators {
+ compatible = "qcom,rpm-pm8998-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+ vdd_s2-supply = <&vph_pwr>;
+ vdd_s3-supply = <&vph_pwr>;
+ vdd_s4-supply = <&vph_pwr>;
+ vdd_s5-supply = <&vph_pwr>;
+ vdd_s6-supply = <&vph_pwr>;
+ vdd_s7-supply = <&vph_pwr>;
+ vdd_s8-supply = <&vph_pwr>;
+ vdd_s9-supply = <&vph_pwr>;
+ vdd_s10-supply = <&vph_pwr>;
+ vdd_s11-supply = <&vph_pwr>;
+ vdd_s12-supply = <&vph_pwr>;
+ vdd_s13-supply = <&vph_pwr>;
+ vdd_l1_l27-supply = <&vreg_s7a_1p025>;
+ vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
+ vdd_l3_l11-supply = <&vreg_s7a_1p025>;
+ vdd_l4_l5-supply = <&vreg_s7a_1p025>;
+ vdd_l6-supply = <&vreg_s5a_2p04>;
+ vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
+ vdd_l9-supply = <&vreg_bob>;
+ vdd_l10_l23_l25-supply = <&vreg_bob>;
+ vdd_l13_l19_l21-supply = <&vreg_bob>;
+ vdd_l16_l28-supply = <&vreg_bob>;
+ vdd_l18_l22-supply = <&vreg_bob>;
+ vdd_l20_l24-supply = <&vreg_bob>;
+ vdd_l26-supply = <&vreg_s3a_1p35>;
+ vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+ vreg_s3a_1p35: s3 {
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+ vreg_s4a_1p8: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-allow-set-load;
+ regulator-system-load = <100000>;
+ };
+ vreg_s5a_2p04: s5 {
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2032000>;
+ };
+ vreg_s7a_1p025: s7 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1028000>;
+ };
+ vreg_l1a_0p875: l1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-system-load = <73400>;
+ regulator-allow-set-load;
+ };
+ vreg_l2a_1p2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-system-load = <12560>;
+ regulator-allow-set-load;
+ };
+ vreg_l3a_1p0: l3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+ vreg_l5a_0p8: l5 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ };
+ vreg_l6a_1p8: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l7a_1p8: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l8a_1p2: l8 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+ vreg_l9a_1p8: l9 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ };
+ vreg_l10a_1p8: l10 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ };
+ vreg_l11a_1p0: l11 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+ vreg_l12a_1p8: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l13a_2p95: l13 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-allow-set-load;
+ };
+ vreg_l14a_1p85: l14 {
+ regulator-min-microvolt = <1848000>;
+ regulator-max-microvolt = <1856000>;
+ regulator-system-load = <32000>;
+ regulator-allow-set-load;
+ };
+ vreg_l15a_1p8: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l16a_2p7: l16 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+ };
+ vreg_l17a_1p3: l17 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ };
+ vreg_l18a_2p85: l18 {};
+ vreg_l19a_2p7: l19 {
+ regulator-min-microvolt = <2696000>;
+ regulator-max-microvolt = <2704000>;
+ };
+ vreg_l20a_2p95: l20 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-allow-set-load;
+ regulator-system-load = <10000>;
+ };
+ vreg_l21a_2p95: l21 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-allow-set-load;
+ regulator-system-load = <800000>;
+ };
+ vreg_l22a_2p85: l22 { };
+ vreg_l23a_3p3: l23 {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3312000>;
+ };
+ vreg_l24a_3p075: l24 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3088000>;
+ };
+ vreg_l25a_3p3: l25 {
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3312000>;
+ };
+ vreg_l26a_1p2: l26 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-allow-set-load;
+ };
+ vreg_l28_3p0: l28 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+ vreg_lvs1a_1p8: lvs1 { };
+ vreg_lvs2a_1p8: lvs2 { };
+
+ };
+
+ pmi8998-regulators {
+ compatible = "qcom,rpm-pmi8998-regulators";
+
+ vdd_bob-supply = <&vph_pwr>;
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3600000>;
+ };
+ };
+};
+
+&sdhc2 {
+ status = "okay";
+ cd-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
+
+ vmmc-supply = <&vreg_l21a_2p95>;
+ vqmmc-supply = <&vreg_l13a_2p95>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ mdp_vsync_n: mdp-vsync-n {
+ pins = "gpio10";
+ function = "mdp_vsync_a";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ nfc_ven: nfc-ven {
+ pins = "gpio12";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ output-low;
+ };
+
+ msm_mclk0_default: msm-mclk0-active {
+ pins = "gpio13";
+ function = "cam_mclk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ msm_mclk1_default: msm-mclk1-active {
+ pins = "gpio14";
+ function = "cam_mclk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ cci0_default: cci0-default {
+ pins = "gpio18", "gpio19";
+ function = "cci_i2c";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cci1_default: cci1-default {
+ pins = "gpio19", "gpio20";
+ function = "cci_i2c";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ hall_sensor0_default: acc-cover-open {
+ pins = "gpio124";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ input-enable;
+ };
+};
+
+/*
+ * WARNING:
+ * Disable UFS until card quirks are in to avoid unrecoverable hard-brick
+ * that would happen as soon as the UFS card gets probed as, without the
+ * required quirks, the bootloader will be erased right after card probe.
+ */
+&ufshc {
+ status = "disabled";
+};
+
+&ufsphy {
+ status = "disabled";
+};
+
+&usb3 {
+ status = "okay";
+};
+
+&usb3_dwc3 {
+ /* Force to peripheral until we have Type-C hooked up */
+ dr_mode = "peripheral";
+};
+
+&usb3phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l2a_1p2>;
+};
--
2.32.0
