From: Chunyan Zhang <chunyan.zhang@xxxxxxxxxx>
ADI r3p0 is used on SC9863 and UMS512 SoCs.
Signed-off-by: Chunyan Zhang <chunyan.zhang@xxxxxxxxxx>
Reviewed-by: Baolin Wang <baolin.wang7@xxxxxxxxx>
---
drivers/spi/spi-sprd-adi.c | 215 ++++++++++++++++++++++++++++---------
1 file changed, 165 insertions(+), 50 deletions(-)
diff --git a/drivers/spi/spi-sprd-adi.c b/drivers/spi/spi-sprd-adi.c
index d392dc6db927..1edbf44c05a7 100644
--- a/drivers/spi/spi-sprd-adi.c
+++ b/drivers/spi/spi-sprd-adi.c
@@ -52,10 +52,20 @@
/*
* ADI slave devices include RTC, ADC, regulator, charger, thermal and so on.
- * The slave devices address offset is always 0x8000 and size is 4K.
+ * ADI supports 12/14bit address for r2p0, and additional 17bit for r3p0 or
+ * later versions. Since bit[1:0] are zero, so the spec describe them as
+ * 10/12/15bit address mode.
+ * The 10bit mode supports sigle slave, 12/15bit mode supports 3 slave, the
+ * high two bits is slave_id.
+ * The slave devices address offset is 0x8000 for 10/12bit address mode,
+ * and 0x20000 for 15bit mode.
*/
-#define ADI_SLAVE_ADDR_SIZE SZ_4K
-#define ADI_SLAVE_OFFSET 0x8000
+#define ADI_10BIT_SLAVE_ADDR_SIZE SZ_4K
+#define ADI_10BIT_SLAVE_OFFSET 0x8000
+#define ADI_12BIT_SLAVE_ADDR_SIZE SZ_16K
+#define ADI_12BIT_SLAVE_OFFSET 0x8000
+#define ADI_15BIT_SLAVE_ADDR_SIZE SZ_128K
+#define ADI_15BIT_SLAVE_OFFSET 0x20000
/* Timeout (ms) for the trylock of hardware spinlocks */
#define ADI_HWSPINLOCK_TIMEOUT 5000
@@ -67,24 +77,35 @@
#define ADI_FIFO_DRAIN_TIMEOUT 1000
#define ADI_READ_TIMEOUT 2000
-#define REG_ADDR_LOW_MASK GENMASK(11, 0)
+
+/*
+ * Read back address from REG_ADI_RD_DATA bit[30:16] which maps to:
+ * REG_ADI_RD_CMD bit[14:0] for r2p0
+ * REG_ADI_RD_CMD bit[16:2] for r3p0
+ */
+#define RDBACK_ADDR_MASK_R2 GENMASK(14, 0)
+#define RDBACK_ADDR_MASK_R3 GENMASK(16, 2)
+#define RDBACK_ADDR_SHIFT_R3 2
/* Registers definitions for PMIC watchdog controller */
-#define REG_WDG_LOAD_LOW 0x80
-#define REG_WDG_LOAD_HIGH 0x84
-#define REG_WDG_CTRL 0x88
-#define REG_WDG_LOCK 0xa0
+#define REG_WDG_LOAD_LOW 0x0
+#define REG_WDG_LOAD_HIGH 0x4
+#define REG_WDG_CTRL 0x8
+#define REG_WDG_LOCK 0x20
/* Bits definitions for register REG_WDG_CTRL */
#define BIT_WDG_RUN BIT(1)
#define BIT_WDG_NEW BIT(2)
#define BIT_WDG_RST BIT(3)
+/* Bits definitions for register REG_MODULE_EN */
+#define BIT_WDG_EN BIT(2)
+
/* Registers definitions for PMIC */
#define PMIC_RST_STATUS 0xee8
#define PMIC_MODULE_EN 0xc08
#define PMIC_CLK_EN 0xc18
-#define BIT_WDG_EN BIT(2)
+#define PMIC_WDG_BASE 0x80
/* Definition of PMIC reset status register */
#define HWRST_STATUS_SECURITY 0x02
@@ -107,6 +128,22 @@
#define WDG_LOAD_MASK GENMASK(15, 0)
#define WDG_UNLOCK_KEY 0xe551
+struct sprd_adi_wdg {
+ u32 base;
+ u32 rst_sts;
+ u32 wdg_en;
+ u32 wdg_clk;
+};
+
+struct sprd_adi_data {
+ u32 slave_offset;
+ u32 slave_addr_size;
+ int (*read_check)(u32 val, u32 reg);
+ int (*restart)(struct notifier_block *this,
+ unsigned long mode, void *cmd);
+ void (*wdg_rst)(void *p);
+};
+
struct sprd_adi {
struct spi_controller *ctlr;
struct device *dev;
@@ -115,11 +152,12 @@ struct sprd_adi {
unsigned long slave_vbase;
unsigned long slave_pbase;
struct notifier_block restart_handler;
+ const struct sprd_adi_data *data;
};
static int sprd_adi_check_addr(struct sprd_adi *sadi, u32 reg)
{
- if (reg >= ADI_SLAVE_ADDR_SIZE) {
+ if (reg >= sadi->data->slave_addr_size) {
dev_err(sadi->dev,
"slave address offset is incorrect, reg = 0x%x\n",
reg);
@@ -155,11 +193,35 @@ static int sprd_adi_fifo_is_full(struct sprd_adi *sadi)
return readl_relaxed(sadi->base + REG_ADI_ARM_FIFO_STS) & BIT_FIFO_FULL;
}
+static int sprd_adi_read_check(u32 val, u32 addr)
+{
+ u32 rd_addr;
+
+ rd_addr = (val & RD_ADDR_MASK) >> RD_ADDR_SHIFT;
+
+ if (rd_addr != addr) {
+ pr_err("ADI read error, addr = 0x%x, val = 0x%x\n", addr, val);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int sprd_adi_read_check_r2(u32 val, u32 reg)
+{
+ return sprd_adi_read_check(val, reg & RDBACK_ADDR_MASK_R2);
+}
+
+static int sprd_adi_read_check_r3(u32 val, u32 reg)
+{
+ return sprd_adi_read_check(val, (reg & RDBACK_ADDR_MASK_R3) >> RDBACK_ADDR_SHIFT_R3);
+}
+
static int sprd_adi_read(struct sprd_adi *sadi, u32 reg, u32 *read_val)
{
int read_timeout = ADI_READ_TIMEOUT;
unsigned long flags;
- u32 val, rd_addr;
+ u32 val;
int ret = 0;
if (sadi->hwlock) {
@@ -203,18 +265,15 @@ static int sprd_adi_read(struct sprd_adi *sadi, u32 reg, u32 *read_val)
}
/*
- * The return value includes data and read register address, from bit 0
- * to bit 15 are data, and from bit 16 to bit 30 are read register
- * address. Then we can check the returned register address to validate
- * data.
+ * The return value before adi r5p0 includes data and read register
+ * address, from bit 0to bit 15 are data, and from bit 16 to bit 30
+ * are read register address. Then we can check the returned register
+ * address to validate data.
*/
- rd_addr = (val & RD_ADDR_MASK) >> RD_ADDR_SHIFT;
-
- if (rd_addr != (reg & REG_ADDR_LOW_MASK)) {
- dev_err(sadi->dev, "read error, reg addr = 0x%x, val = 0x%x\n",
- reg, val);
- ret = -EIO;
- goto out;
+ if (sadi->data->read_check) {
+ ret = sadi->data->read_check(val, reg);
+ if (ret < 0)
+ goto out;
}
*read_val = val & RD_VALUE_MASK;
@@ -299,20 +358,21 @@ static int sprd_adi_transfer_one(struct spi_controller *ctlr,
return ret;
}
-static void sprd_adi_set_wdt_rst_mode(struct sprd_adi *sadi)
+static void sprd_adi_set_wdt_rst_mode(void *p)
{
#if IS_ENABLED(CONFIG_SPRD_WATCHDOG)
u32 val;
+ struct sprd_adi *sadi = (struct sprd_adi *)p;
- /* Set default watchdog reboot mode */
+ /* Init watchdog reset mode */
sprd_adi_read(sadi, PMIC_RST_STATUS, &val);
val |= HWRST_STATUS_WATCHDOG;
sprd_adi_write(sadi, PMIC_RST_STATUS, val);
#endif
}
-static int sprd_adi_restart_handler(struct notifier_block *this,
- unsigned long mode, void *cmd)
+static int sprd_adi_restart(struct notifier_block *this, unsigned long mode,
+ void *cmd, struct sprd_adi_wdg *wdg)
{
struct sprd_adi *sadi = container_of(this, struct sprd_adi,
restart_handler);
@@ -348,40 +408,40 @@ static int sprd_adi_restart_handler(struct notifier_block *this,
reboot_mode = HWRST_STATUS_NORMAL;
/* Record the reboot mode */
- sprd_adi_read(sadi, PMIC_RST_STATUS, &val);
+ sprd_adi_read(sadi, wdg->rst_sts, &val);
val &= ~HWRST_STATUS_WATCHDOG;
val |= reboot_mode;
- sprd_adi_write(sadi, PMIC_RST_STATUS, val);
+ sprd_adi_write(sadi, wdg->rst_sts, val);
/* Enable the interface clock of the watchdog */
- sprd_adi_read(sadi, PMIC_MODULE_EN, &val);
+ sprd_adi_read(sadi, wdg->wdg_en, &val);
val |= BIT_WDG_EN;
- sprd_adi_write(sadi, PMIC_MODULE_EN, val);
+ sprd_adi_write(sadi, wdg->wdg_en, val);
/* Enable the work clock of the watchdog */
- sprd_adi_read(sadi, PMIC_CLK_EN, &val);
+ sprd_adi_read(sadi, wdg->wdg_clk, &val);
val |= BIT_WDG_EN;
- sprd_adi_write(sadi, PMIC_CLK_EN, val);
+ sprd_adi_write(sadi, wdg->wdg_clk, val);
/* Unlock the watchdog */
- sprd_adi_write(sadi, REG_WDG_LOCK, WDG_UNLOCK_KEY);
+ sprd_adi_write(sadi, wdg->base + REG_WDG_LOCK, WDG_UNLOCK_KEY);
- sprd_adi_read(sadi, REG_WDG_CTRL, &val);
+ sprd_adi_read(sadi, wdg->base + REG_WDG_CTRL, &val);
val |= BIT_WDG_NEW;
- sprd_adi_write(sadi, REG_WDG_CTRL, val);
+ sprd_adi_write(sadi, wdg->base + REG_WDG_CTRL, val);
/* Load the watchdog timeout value, 50ms is always enough. */
- sprd_adi_write(sadi, REG_WDG_LOAD_HIGH, 0);
- sprd_adi_write(sadi, REG_WDG_LOAD_LOW,
+ sprd_adi_write(sadi, wdg->base + REG_WDG_LOAD_HIGH, 0);
+ sprd_adi_write(sadi, wdg->base + REG_WDG_LOAD_LOW,
WDG_LOAD_VAL & WDG_LOAD_MASK);
/* Start the watchdog to reset system */
- sprd_adi_read(sadi, REG_WDG_CTRL, &val);
+ sprd_adi_read(sadi, wdg->base + REG_WDG_CTRL, &val);
val |= BIT_WDG_RUN | BIT_WDG_RST;
- sprd_adi_write(sadi, REG_WDG_CTRL, val);
+ sprd_adi_write(sadi, wdg->base + REG_WDG_CTRL, val);
/* Lock the watchdog */
- sprd_adi_write(sadi, REG_WDG_LOCK, ~WDG_UNLOCK_KEY);
+ sprd_adi_write(sadi, wdg->base + REG_WDG_LOCK, ~WDG_UNLOCK_KEY);
mdelay(1000);
@@ -389,6 +449,19 @@ static int sprd_adi_restart_handler(struct notifier_block *this,
return NOTIFY_DONE;
}
+static int sprd_adi_restart_sc9860(struct notifier_block *this,
+ unsigned long mode, void *cmd)
+{
+ struct sprd_adi_wdg wdg = {
+ .base = PMIC_WDG_BASE,
+ .rst_sts = PMIC_RST_STATUS,
+ .wdg_en = PMIC_MODULE_EN,
+ .wdg_clk = PMIC_CLK_EN,
+ };
+
+ return sprd_adi_restart(this, mode, cmd, &wdg);
+}
+
static void sprd_adi_hw_init(struct sprd_adi *sadi)
{
struct device_node *np = sadi->dev->of_node;
@@ -440,10 +513,11 @@ static void sprd_adi_hw_init(struct sprd_adi *sadi)
static int sprd_adi_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
+ const struct sprd_adi_data *data;
struct spi_controller *ctlr;
struct sprd_adi *sadi;
struct resource *res;
- u32 num_chipselect;
+ u16 num_chipselect;
int ret;
if (!np) {
@@ -451,6 +525,12 @@ static int sprd_adi_probe(struct platform_device *pdev)
return -ENODEV;
}
+ data = of_device_get_match_data(&pdev->dev);
+ if (!data) {
+ dev_err(&pdev->dev, "no matching driver data found\n");
+ return -EINVAL;
+ }
+
pdev->id = of_alias_get_id(np, "spi");
num_chipselect = of_get_child_count(np);
@@ -468,10 +548,12 @@ static int sprd_adi_probe(struct platform_device *pdev)
goto put_ctlr;
}
- sadi->slave_vbase = (unsigned long)sadi->base + ADI_SLAVE_OFFSET;
- sadi->slave_pbase = res->start + ADI_SLAVE_OFFSET;
+ sadi->slave_vbase = (unsigned long)sadi->base +
+ data->slave_offset;
+ sadi->slave_pbase = res->start + data->slave_offset;
sadi->ctlr = ctlr;
sadi->dev = &pdev->dev;
+ sadi->data = data;
ret = of_hwspin_lock_get_id(np, 0);
if (ret > 0 || (IS_ENABLED(CONFIG_HWSPINLOCK) && ret == 0)) {
sadi->hwlock =
@@ -492,7 +574,9 @@ static int sprd_adi_probe(struct platform_device *pdev)
}
sprd_adi_hw_init(sadi);
- sprd_adi_set_wdt_rst_mode(sadi);
+
+ if (sadi->data->wdg_rst)
+ sadi->data->wdg_rst(sadi);
ctlr->dev.of_node = pdev->dev.of_node;
ctlr->bus_num = pdev->id;
@@ -507,12 +591,14 @@ static int sprd_adi_probe(struct platform_device *pdev)
goto put_ctlr;
}
- sadi->restart_handler.notifier_call = sprd_adi_restart_handler;
- sadi->restart_handler.priority = 128;
- ret = register_restart_handler(&sadi->restart_handler);
- if (ret) {
- dev_err(&pdev->dev, "can not register restart handler\n");
- goto put_ctlr;
+ if (sadi->data->restart) {
+ sadi->restart_handler.notifier_call = sadi->data->restart;
+ sadi->restart_handler.priority = 128;
+ ret = register_restart_handler(&sadi->restart_handler);
+ if (ret) {
+ dev_err(&pdev->dev, "can not register restart handler\n");
+ goto put_ctlr;
+ }
}
return 0;
@@ -531,9 +617,38 @@ static int sprd_adi_remove(struct platform_device *pdev)
return 0;
}
+static struct sprd_adi_data sc9860_data = {
+ .slave_offset = ADI_10BIT_SLAVE_OFFSET,
+ .slave_addr_size = ADI_10BIT_SLAVE_ADDR_SIZE,
+ .read_check = sprd_adi_read_check_r2,
+ .restart = sprd_adi_restart_sc9860,
+ .wdg_rst = sprd_adi_set_wdt_rst_mode,
+};
+
+static struct sprd_adi_data sc9863_data = {
+ .slave_offset = ADI_12BIT_SLAVE_OFFSET,
+ .slave_addr_size = ADI_12BIT_SLAVE_ADDR_SIZE,
+ .read_check = sprd_adi_read_check_r3,
+};
+
+static struct sprd_adi_data ums512_data = {
+ .slave_offset = ADI_15BIT_SLAVE_OFFSET,
+ .slave_addr_size = ADI_15BIT_SLAVE_ADDR_SIZE,
+ .read_check = sprd_adi_read_check_r3,
+};
+
static const struct of_device_id sprd_adi_of_match[] = {
{
.compatible = "sprd,sc9860-adi",
+ .data = &sc9860_data,
+ },
+ {
+ .compatible = "sprd,sc9863-adi",
+ .data = &sc9863_data,
+ },
+ {
+ .compatible = "sprd,ums512-adi",
+ .data = &ums512_data,
},
{ },
};
--
2.25.1
