Hi Chunyan,
On Wed, Aug 25, 2021 at 2:59 PM Chunyan Zhang <zhang.lyra@xxxxxxxxx> wrote:
>
> From: Chunyan Zhang <chunyan.zhang@xxxxxxxxxx>
>
> ADI r3p0 is used on SC9863 and UMS512 SoCs.
>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@xxxxxxxxxx>
> ---
> drivers/spi/spi-sprd-adi.c | 218 ++++++++++++++++++++++++++++---------
> 1 file changed, 167 insertions(+), 51 deletions(-)
>
> diff --git a/drivers/spi/spi-sprd-adi.c b/drivers/spi/spi-sprd-adi.c
> index 07f11b17bf20..5ec1845d8e5b 100644
> --- a/drivers/spi/spi-sprd-adi.c
> +++ b/drivers/spi/spi-sprd-adi.c
> @@ -52,10 +52,20 @@
>
> /*
> * ADI slave devices include RTC, ADC, regulator, charger, thermal and so on.
> - * The slave devices address offset is always 0x8000 and size is 4K.
> + * ADI supports 12/14bit address for r2p0, and additional 17bit for r3p0 or
> + * later versions. Since bit[1:0] are zero, so the spec describe them as
> + * 10/12/15bit address mode.
> + * The 10bit mode supports sigle slave, 12/15bit mode supports 3 slave, the
> + * high two bits is slave_id.
> + * The slave devices address offset is 0x8000 for 10/12bit address mode,
> + * and 0x20000 for 15bit mode.
> */
> -#define ADI_SLAVE_ADDR_SIZE SZ_4K
> -#define ADI_SLAVE_OFFSET 0x8000
> +#define ADI_10BIT_SLAVE_ADDR_SIZE SZ_4K
> +#define ADI_10BIT_SLAVE_OFFSET 0x8000
> +#define ADI_12BIT_SLAVE_ADDR_SIZE SZ_16K
> +#define ADI_12BIT_SLAVE_OFFSET 0x8000
> +#define ADI_15BIT_SLAVE_ADDR_SIZE SZ_128K
> +#define ADI_15BIT_SLAVE_OFFSET 0x20000
>
> /* Timeout (ms) for the trylock of hardware spinlocks */
> #define ADI_HWSPINLOCK_TIMEOUT 5000
> @@ -67,24 +77,35 @@
>
> #define ADI_FIFO_DRAIN_TIMEOUT 1000
> #define ADI_READ_TIMEOUT 2000
> -#define REG_ADDR_LOW_MASK GENMASK(11, 0)
> +
> +/*
> + * Read back address from REG_ADI_RD_DATA bit[30:16] which maps to:
> + * REG_ADI_RD_CMD bit[14:0] for r2p0
> + * REG_ADI_RD_CMD bit[16:2] for r3p0
> + */
> +#define RDBACK_ADDR_MASK_R2 GENMASK(14, 0)
> +#define RDBACK_ADDR_MASK_R3 GENMASK(16, 2)
> +#define RDBACK_ADDR_SHIFT_R3 2
>
> /* Registers definitions for PMIC watchdog controller */
> -#define REG_WDG_LOAD_LOW 0x80
> -#define REG_WDG_LOAD_HIGH 0x84
> -#define REG_WDG_CTRL 0x88
> -#define REG_WDG_LOCK 0xa0
> +#define REG_WDG_LOAD_LOW 0x0
> +#define REG_WDG_LOAD_HIGH 0x4
> +#define REG_WDG_CTRL 0x8
> +#define REG_WDG_LOCK 0x20
>
> /* Bits definitions for register REG_WDG_CTRL */
> #define BIT_WDG_RUN BIT(1)
> #define BIT_WDG_NEW BIT(2)
> #define BIT_WDG_RST BIT(3)
>
> +/* Bits definitions for register REG_MODULE_EN */
> +#define BIT_WDG_EN BIT(2)
> +
> /* Registers definitions for PMIC */
> #define PMIC_RST_STATUS 0xee8
> #define PMIC_MODULE_EN 0xc08
> #define PMIC_CLK_EN 0xc18
> -#define BIT_WDG_EN BIT(2)
> +#define PMIC_WDG_BASE 0x80
>
> /* Definition of PMIC reset status register */
> #define HWRST_STATUS_SECURITY 0x02
> @@ -103,10 +124,26 @@
> #define HWRST_STATUS_WATCHDOG 0xf0
>
> /* Use default timeout 50 ms that converts to watchdog values */
> -#define WDG_LOAD_VAL ((50 * 1000) / 32768)
> +#define WDG_LOAD_VAL ((50 * 32768) / 1000)
If this is an incorrect formula, it deserves a stable patch with some
explanation.
> #define WDG_LOAD_MASK GENMASK(15, 0)
> #define WDG_UNLOCK_KEY 0xe551
>
> +struct sprd_adi_wdg {
> + u32 base;
> + u32 rst_sts;
> + u32 wdg_en;
> + u32 wdg_clk;
> +};
> +
> +struct sprd_adi_data {
> + u32 slave_offset;
> + u32 slave_addr_size;
> + int (*read_check)(u32 val, u32 reg);
> + int (*restart)(struct notifier_block *this,
> + unsigned long mode, void *cmd);
> + void (*wdg_rst)(void *p);
> +};
> +
> struct sprd_adi {
> struct spi_controller *ctlr;
> struct device *dev;
> @@ -115,11 +152,12 @@ struct sprd_adi {
> unsigned long slave_vbase;
> unsigned long slave_pbase;
> struct notifier_block restart_handler;
> + const struct sprd_adi_data *data;
> };
>
> static int sprd_adi_check_addr(struct sprd_adi *sadi, u32 reg)
> {
> - if (reg >= ADI_SLAVE_ADDR_SIZE) {
> + if (reg >= sadi->data->slave_addr_size) {
> dev_err(sadi->dev,
> "slave address offset is incorrect, reg = 0x%x\n",
> reg);
> @@ -155,11 +193,35 @@ static int sprd_adi_fifo_is_full(struct sprd_adi *sadi)
> return readl_relaxed(sadi->base + REG_ADI_ARM_FIFO_STS) & BIT_FIFO_FULL;
> }
>
> +static int sprd_adi_read_check(u32 val, u32 addr)
> +{
> + u32 rd_addr;
> +
> + rd_addr = (val & RD_ADDR_MASK) >> RD_ADDR_SHIFT;
> +
> + if (rd_addr != addr) {
> + pr_err("ADI read error, addr = 0x%x, val = 0x%x\n", addr, val);
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static int sprd_adi_read_check_r2(u32 val, u32 reg)
> +{
> + return sprd_adi_read_check(val, reg & RDBACK_ADDR_MASK_R2);
> +}
> +
> +static int sprd_adi_read_check_r3(u32 val, u32 reg)
> +{
> + return sprd_adi_read_check(val, (reg & RDBACK_ADDR_MASK_R3) >> RDBACK_ADDR_SHIFT_R3);
> +}
> +
> static int sprd_adi_read(struct sprd_adi *sadi, u32 reg, u32 *read_val)
> {
> int read_timeout = ADI_READ_TIMEOUT;
> unsigned long flags;
> - u32 val, rd_addr;
> + u32 val;
> int ret = 0;
>
> if (sadi->hwlock) {
> @@ -203,18 +265,15 @@ static int sprd_adi_read(struct sprd_adi *sadi, u32 reg, u32 *read_val)
> }
>
> /*
> - * The return value includes data and read register address, from bit 0
> - * to bit 15 are data, and from bit 16 to bit 30 are read register
> - * address. Then we can check the returned register address to validate
> - * data.
> + * The return value before adi r5p0 includes data and read register
> + * address, from bit 0to bit 15 are data, and from bit 16 to bit 30
> + * are read register address. Then we can check the returned register
> + * address to validate data.
> */
> - rd_addr = (val & RD_ADDR_MASK) >> RD_ADDR_SHIFT;
> -
> - if (rd_addr != (reg & REG_ADDR_LOW_MASK)) {
> - dev_err(sadi->dev, "read error, reg addr = 0x%x, val = 0x%x\n",
> - reg, val);
> - ret = -EIO;
> - goto out;
> + if (sadi->data->read_check) {
> + ret = sadi->data->read_check(val, reg);
> + if (ret < 0)
> + goto out;
> }
>
> *read_val = val & RD_VALUE_MASK;
> @@ -299,20 +358,22 @@ static int sprd_adi_transfer_one(struct spi_controller *ctlr,
> return ret;
> }
>
> -static void sprd_adi_set_wdt_rst_mode(struct sprd_adi *sadi)
> +static void sprd_adi_set_wdt_rst_mode(void *p)
> {
> #if IS_ENABLED(CONFIG_SPRD_WATCHDOG)
> u32 val;
> + struct sprd_adi *sadi = (struct sprd_adi *)p;
>
> - /* Set default watchdog reboot mode */
> +
Remove the redundant blank line. Otherwise looks good to me.
Reviewed-by: Baolin Wang <baolin.wang7@xxxxxxxxx>
> + /* Init watchdog reset mode */
> sprd_adi_read(sadi, PMIC_RST_STATUS, &val);
> val |= HWRST_STATUS_WATCHDOG;
> sprd_adi_write(sadi, PMIC_RST_STATUS, val);
> #endif
> }
>
> -static int sprd_adi_restart_handler(struct notifier_block *this,
> - unsigned long mode, void *cmd)
> +static int sprd_adi_restart(struct notifier_block *this, unsigned long mode,
> + void *cmd, struct sprd_adi_wdg *wdg)
> {
> struct sprd_adi *sadi = container_of(this, struct sprd_adi,
> restart_handler);
> @@ -348,40 +409,40 @@ static int sprd_adi_restart_handler(struct notifier_block *this,
> reboot_mode = HWRST_STATUS_NORMAL;
>
> /* Record the reboot mode */
> - sprd_adi_read(sadi, PMIC_RST_STATUS, &val);
> + sprd_adi_read(sadi, wdg->rst_sts, &val);
> val &= ~HWRST_STATUS_WATCHDOG;
> val |= reboot_mode;
> - sprd_adi_write(sadi, PMIC_RST_STATUS, val);
> + sprd_adi_write(sadi, wdg->rst_sts, val);
>
> /* Enable the interface clock of the watchdog */
> - sprd_adi_read(sadi, PMIC_MODULE_EN, &val);
> + sprd_adi_read(sadi, wdg->wdg_en, &val);
> val |= BIT_WDG_EN;
> - sprd_adi_write(sadi, PMIC_MODULE_EN, val);
> + sprd_adi_write(sadi, wdg->wdg_en, val);
>
> /* Enable the work clock of the watchdog */
> - sprd_adi_read(sadi, PMIC_CLK_EN, &val);
> + sprd_adi_read(sadi, wdg->wdg_clk, &val);
> val |= BIT_WDG_EN;
> - sprd_adi_write(sadi, PMIC_CLK_EN, val);
> + sprd_adi_write(sadi, wdg->wdg_clk, val);
>
> /* Unlock the watchdog */
> - sprd_adi_write(sadi, REG_WDG_LOCK, WDG_UNLOCK_KEY);
> + sprd_adi_write(sadi, wdg->base + REG_WDG_LOCK, WDG_UNLOCK_KEY);
>
> - sprd_adi_read(sadi, REG_WDG_CTRL, &val);
> + sprd_adi_read(sadi, wdg->base + REG_WDG_CTRL, &val);
> val |= BIT_WDG_NEW;
> - sprd_adi_write(sadi, REG_WDG_CTRL, val);
> + sprd_adi_write(sadi, wdg->base + REG_WDG_CTRL, val);
>
> /* Load the watchdog timeout value, 50ms is always enough. */
> - sprd_adi_write(sadi, REG_WDG_LOAD_HIGH, 0);
> - sprd_adi_write(sadi, REG_WDG_LOAD_LOW,
> + sprd_adi_write(sadi, wdg->base + REG_WDG_LOAD_HIGH, 0);
> + sprd_adi_write(sadi, wdg->base + REG_WDG_LOAD_LOW,
> WDG_LOAD_VAL & WDG_LOAD_MASK);
>
> /* Start the watchdog to reset system */
> - sprd_adi_read(sadi, REG_WDG_CTRL, &val);
> + sprd_adi_read(sadi, wdg->base + REG_WDG_CTRL, &val);
> val |= BIT_WDG_RUN | BIT_WDG_RST;
> - sprd_adi_write(sadi, REG_WDG_CTRL, val);
> + sprd_adi_write(sadi, wdg->base + REG_WDG_CTRL, val);
>
> /* Lock the watchdog */
> - sprd_adi_write(sadi, REG_WDG_LOCK, ~WDG_UNLOCK_KEY);
> + sprd_adi_write(sadi, wdg->base + REG_WDG_LOCK, ~WDG_UNLOCK_KEY);
>
> mdelay(1000);
>
> @@ -389,6 +450,19 @@ static int sprd_adi_restart_handler(struct notifier_block *this,
> return NOTIFY_DONE;
> }
>
> +static int sprd_adi_restart_sc9860(struct notifier_block *this,
> + unsigned long mode, void *cmd)
> +{
> + struct sprd_adi_wdg wdg = {
> + .base = PMIC_WDG_BASE,
> + .rst_sts = PMIC_RST_STATUS,
> + .wdg_en = PMIC_MODULE_EN,
> + .wdg_clk = PMIC_CLK_EN,
> + };
> +
> + return sprd_adi_restart(this, mode, cmd, &wdg);
> +}
> +
> static void sprd_adi_hw_init(struct sprd_adi *sadi)
> {
> struct device_node *np = sadi->dev->of_node;
> @@ -440,10 +514,11 @@ static void sprd_adi_hw_init(struct sprd_adi *sadi)
> static int sprd_adi_probe(struct platform_device *pdev)
> {
> struct device_node *np = pdev->dev.of_node;
> + const struct sprd_adi_data *data;
> struct spi_controller *ctlr;
> struct sprd_adi *sadi;
> struct resource *res;
> - u32 num_chipselect;
> + u16 num_chipselect;
> int ret;
>
> if (!np) {
> @@ -451,6 +526,12 @@ static int sprd_adi_probe(struct platform_device *pdev)
> return -ENODEV;
> }
>
> + data = of_device_get_match_data(&pdev->dev);
> + if (!data) {
> + dev_err(&pdev->dev, "no matching driver data found\n");
> + return -EINVAL;
> + }
> +
> pdev->id = of_alias_get_id(np, "spi");
> num_chipselect = of_get_child_count(np);
>
> @@ -468,10 +549,12 @@ static int sprd_adi_probe(struct platform_device *pdev)
> goto put_ctlr;
> }
>
> - sadi->slave_vbase = (unsigned long)sadi->base + ADI_SLAVE_OFFSET;
> - sadi->slave_pbase = res->start + ADI_SLAVE_OFFSET;
> + sadi->slave_vbase = (unsigned long)sadi->base +
> + data->slave_offset;
> + sadi->slave_pbase = res->start + data->slave_offset;
> sadi->ctlr = ctlr;
> sadi->dev = &pdev->dev;
> + sadi->data = data;
> ret = of_hwspin_lock_get_id(np, 0);
> if (ret > 0 || (IS_ENABLED(CONFIG_HWSPINLOCK) && ret == 0)) {
> sadi->hwlock =
> @@ -492,7 +575,9 @@ static int sprd_adi_probe(struct platform_device *pdev)
> }
>
> sprd_adi_hw_init(sadi);
> - sprd_adi_set_wdt_rst_mode(sadi);
> +
> + if (sadi->data->wdg_rst)
> + sadi->data->wdg_rst(sadi);
>
> ctlr->dev.of_node = pdev->dev.of_node;
> ctlr->bus_num = pdev->id;
> @@ -507,12 +592,14 @@ static int sprd_adi_probe(struct platform_device *pdev)
> goto put_ctlr;
> }
>
> - sadi->restart_handler.notifier_call = sprd_adi_restart_handler;
> - sadi->restart_handler.priority = 128;
> - ret = register_restart_handler(&sadi->restart_handler);
> - if (ret) {
> - dev_err(&pdev->dev, "can not register restart handler\n");
> - goto put_ctlr;
> + if (sadi->data->restart) {
> + sadi->restart_handler.notifier_call = sadi->data->restart;
> + sadi->restart_handler.priority = 128;
> + ret = register_restart_handler(&sadi->restart_handler);
> + if (ret) {
> + dev_err(&pdev->dev, "can not register restart handler\n");
> + goto put_ctlr;
> + }
> }
>
> return 0;
> @@ -531,9 +618,38 @@ static int sprd_adi_remove(struct platform_device *pdev)
> return 0;
> }
>
> +static struct sprd_adi_data sc9860_data = {
> + .slave_offset = ADI_10BIT_SLAVE_OFFSET,
> + .slave_addr_size = ADI_10BIT_SLAVE_ADDR_SIZE,
> + .read_check = sprd_adi_read_check_r2,
> + .restart = sprd_adi_restart_sc9860,
> + .wdg_rst = sprd_adi_set_wdt_rst_mode,
> +};
> +
> +static struct sprd_adi_data sc9863_data = {
> + .slave_offset = ADI_12BIT_SLAVE_OFFSET,
> + .slave_addr_size = ADI_12BIT_SLAVE_ADDR_SIZE,
> + .read_check = sprd_adi_read_check_r3,
> +};
> +
> +static struct sprd_adi_data ums512_data = {
> + .slave_offset = ADI_15BIT_SLAVE_OFFSET,
> + .slave_addr_size = ADI_15BIT_SLAVE_ADDR_SIZE,
> + .read_check = sprd_adi_read_check_r3,
> +};
> +
> static const struct of_device_id sprd_adi_of_match[] = {
> {
> .compatible = "sprd,sc9860-adi",
> + .data = &sc9860_data,
> + },
> + {
> + .compatible = "sprd,sc9863-adi",
> + .data = &sc9863_data,
> + },
> + {
> + .compatible = "sprd,ums512-adi",
> + .data = &ums512_data,
> },
> { },
> };
> --
> 2.25.1
>
--
Baolin Wang
