On Fri, Aug 20, 2021 at 08:27:29PM +0200, Nicolas Frattaroli wrote: > This adds the YAML bindings for the Rockchip I2S/TDM audio driver. > > Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@xxxxxxxxx> > --- > .../bindings/sound/rockchip,i2s-tdm.yaml | 193 ++++++++++++++++++ > 1 file changed, 193 insertions(+) > create mode 100644 Documentation/devicetree/bindings/sound/rockchip,i2s-tdm.yaml > > diff --git a/Documentation/devicetree/bindings/sound/rockchip,i2s-tdm.yaml b/Documentation/devicetree/bindings/sound/rockchip,i2s-tdm.yaml > new file mode 100644 > index 000000000000..1e8c1500ba40 > --- /dev/null > +++ b/Documentation/devicetree/bindings/sound/rockchip,i2s-tdm.yaml > @@ -0,0 +1,193 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/sound/rockchip,i2s-tdm.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Rockchip I2S/TDM Controller > + > +description: > + The Rockchip I2S/TDM Controller is a Time Division Multiplexed > + audio interface found in various Rockchip SoCs, allowing up > + to 8 channels of audio over a serial interface. > + > +maintainers: > + - Nicolas Frattaroli <frattaroli.nicolas@xxxxxxxxx> > + > +properties: > + compatible: > + enum: > + - rockchip,px30-i2s-tdm > + - rockchip,rk1808-i2s-tdm > + - rockchip,rk3308-i2s-tdm > + - rockchip,rk3568-i2s-tdm > + - rockchip,rv1126-i2s-tdm > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + dmas: > + minItems: 1 > + maxItems: 2 > + > + dma-names: > + minItems: 1 > + items: > + - const: rx > + - const: tx > + > + clocks: > + items: > + - description: clock for TX > + - description: clock for RX > + - description: AHB clock driving the interface > + > + clock-names: > + items: > + - const: mclk_tx > + - const: mclk_rx > + - const: hclk > + > + rockchip,frame-width: > + $ref: /schemas/types.yaml#/definitions/uint32 > + default: 64 > + minimum: 32 > + maximum: 512 > + description: > + Width of a frame, usually slot width multiplied by number of slots. > + Must be even. > + > + resets: > + items: > + - description: reset for TX > + - description: reset for RX > + > + reset-names: > + items: > + - const: tx-m > + - const: rx-m > + > + rockchip,cru: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + The phandle of the cru. > + Required if both playback and capture are used, i.e. if rockchip,clk-trcm > + is 0. Another case of the nonexistent rockchip,clk-trcm. > + > + rockchip,grf: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + The phandle of the syscon node for the GRF register. > + > + rockchip,mclk-calibrate: > + description: > + Enable mclk source calibration. > + type: boolean > + > + rockchip,trcm-sync-tx-only: > + type: boolean > + description: Use TX BCLK/LRCK for both TX and RX. > + > + rockchip,trcm-sync-rx-only: > + type: boolean > + description: Use RX BCLK/LRCK for both TX and RX. > + > + "#sound-dai-cells": > + const: 0 > + > + rockchip,i2s-rx-route: > + $ref: /schemas/types.yaml#/definitions/uint32-array > + description: > + Defines the mapping of I2S RX sdis to I2S data bus lines. > + By default, they are mapped one-to-one. > + items: > + - description: which sdi to connect to data line 0 > + - description: which sdi to connect to data line 1 > + - description: which sdi to connect to data line 2 > + - description: which sdi to connect to data line 3 > + > + rockchip,i2s-tx-route: > + $ref: /schemas/types.yaml#/definitions/uint32-array > + description: > + Defines the mapping of I2S TX sdos to I2S data bus lines. > + By default, they are mapped one-to-one. > + items: > + - description: which sdo to connect to data line 0 > + - description: which sdo to connect to data line 1 > + - description: which sdo to connect to data line 2 > + - description: which sdo to connect to data line 3 > + > + rockchip,tdm-fsync-half-frame: > + description: Whether to use half frame fsync. > + type: boolean > + > + > +required: > + - compatible > + - reg > + - interrupts > + - dmas > + - dma-names > + - clocks > + - clock-names > + - resets > + - reset-names > + - rockchip,grf > + - "#sound-dai-cells" > + > +allOf: > + - if: > + properties: > + rockchip,trcm-sync-tx-only: false > + rockchip,trcm-sync-rx-only: false > + then: > + required: > + - rockchip,cru > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/clock/rk3568-cru.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/interrupt-controller/irq.h> > + #include <dt-bindings/pinctrl/rockchip.h> > + > + foo { > + #address-cells = <2>; > + #size-cells = <2>; > + i2s@fe410000 { > + compatible = "rockchip,rk3568-i2s-tdm"; > + reg = <0x0 0xfe410000 0x0 0x1000>; > + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cru MCLK_I2S1_8CH_TX>, <&cru MCLK_I2S1_8CH_RX>, > + <&cru HCLK_I2S1_8CH>; > + clock-names = "mclk_tx", "mclk_rx", "hclk"; > + dmas = <&dmac1 3>, <&dmac1 2>; > + dma-names = "rx", "tx"; > + resets = <&cru SRST_M_I2S1_8CH_TX>, <&cru SRST_M_I2S1_8CH_RX>; > + reset-names = "tx-m", "rx-m"; > + rockchip,trcm-sync-tx-only; > + rockchip,cru = <&cru>; > + rockchip,grf = <&grf>; > + #sound-dai-cells = <0>; > + pinctrl-names = "default"; > + pinctrl-0 = > + <&i2s1m0_sclktx > + &i2s1m0_sclkrx > + &i2s1m0_lrcktx > + &i2s1m0_lrckrx > + &i2s1m0_sdi0 > + &i2s1m0_sdi1 > + &i2s1m0_sdi2 > + &i2s1m0_sdi3 > + &i2s1m0_sdo0 > + &i2s1m0_sdo1 > + &i2s1m0_sdo2 > + &i2s1m0_sdo3>; > + status = "okay"; Sorry if I wasn't clear, but you don't need status at all in examples as okay is the default. Rob
