From: Alvin Šipraga <alsi@xxxxxxxxxxxxxxx>
This patch adds a realtek-smi subdriver for the RTL8365MB-VC 4+1 port
10/100/1000M Ethernet switch controller. The driver has been developed
based on a GPL-licensed OS-agnostic Realtek vendor driver known as
rtl8367c found in the OpenWrt source tree.
Despite the name, the RTL8365MB-VC has an entirely different register
layout to the already-supported RTL8366RB ASIC. Notwithstanding this,
the structure of the rtl8365mb subdriver is based on the rtl8366rb
subdriver and makes use of the rtl8366 helper library for VLAN
configuration. Like the 'rb, it establishes its own irqchip to handle
cascaded PHY link status interrupts.
The RTL8365MB-VC is a capable switch and provides a number of offload
features that are not yet supported by this subdriver. However, the
basic functionality should be the same as that the rtl8366rb, modulo LED
support, Energy-Efficient Ethernet (EEE), and MTU configuration. Support
for these features - and more - may follow.
One more thing. Realtek's nomenclature for switches makes it hard to
know exactly what other ASICs might be supported by this driver. The
vendor driver goes by the name rtl8367c, but as far as I can tell, no
chip actually exists under this name. As such, the subdriver is named
rtl8365mb to emphasize the potentially limited support. But it is clear
from the vendor sources that a number of other more advanced switches
share a similar register layout, and further support should not be too
hard to add given access to the relevant hardware. With this in mind,
the subdriver has been written with as few assumptions about the
particular chip as is reasonable. But the RTL8365MB-VC is the only
hardware I have available, so some further work is surely needed.
Signed-off-by: Alvin Šipraga <alsi@xxxxxxxxxxxxxxx>
Co-developed-by: Michael Rasmussen <mir@xxxxxxxxxxxxxxx>
Signed-off-by: Michael Rasmussen <mir@xxxxxxxxxxxxxxx>
---
drivers/net/dsa/Kconfig | 1 +
drivers/net/dsa/Makefile | 2 +-
drivers/net/dsa/realtek-smi-core.c | 4 +
drivers/net/dsa/realtek-smi-core.h | 1 +
drivers/net/dsa/rtl8365mb.c | 2124 ++++++++++++++++++++++++++++
5 files changed, 2131 insertions(+), 1 deletion(-)
create mode 100644 drivers/net/dsa/rtl8365mb.c
diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig
index a5f1aa911fe2..7b1457a6e327 100644
--- a/drivers/net/dsa/Kconfig
+++ b/drivers/net/dsa/Kconfig
@@ -70,6 +70,7 @@ config NET_DSA_QCA8K
config NET_DSA_REALTEK_SMI
tristate "Realtek SMI Ethernet switch family support"
select NET_DSA_TAG_RTL4_A
+ select NET_DSA_TAG_RTL8_4
select FIXED_PHY
select IRQ_DOMAIN
select REALTEK_PHY
diff --git a/drivers/net/dsa/Makefile b/drivers/net/dsa/Makefile
index f3598c040994..8da1569a34e6 100644
--- a/drivers/net/dsa/Makefile
+++ b/drivers/net/dsa/Makefile
@@ -10,7 +10,7 @@ obj-$(CONFIG_NET_DSA_MT7530) += mt7530.o
obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
obj-$(CONFIG_NET_DSA_QCA8K) += qca8k.o
obj-$(CONFIG_NET_DSA_REALTEK_SMI) += realtek-smi.o
-realtek-smi-objs := realtek-smi-core.o rtl8366.o rtl8366rb.o
+realtek-smi-objs := realtek-smi-core.o rtl8366.o rtl8366rb.o rtl8365mb.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303_I2C) += lan9303_i2c.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303_MDIO) += lan9303_mdio.o
diff --git a/drivers/net/dsa/realtek-smi-core.c b/drivers/net/dsa/realtek-smi-core.c
index 6992b6b31db6..d64f85c47891 100644
--- a/drivers/net/dsa/realtek-smi-core.c
+++ b/drivers/net/dsa/realtek-smi-core.c
@@ -490,6 +490,10 @@ static const struct of_device_id realtek_smi_of_match[] = {
.compatible = "realtek,rtl8366s",
.data = NULL,
},
+ {
+ .compatible = "realtek,rtl8365mb",
+ .data = &rtl8365mb_variant,
+ },
{ /* sentinel */ },
};
MODULE_DEVICE_TABLE(of, realtek_smi_of_match);
diff --git a/drivers/net/dsa/realtek-smi-core.h b/drivers/net/dsa/realtek-smi-core.h
index 6cfa5f2df7ea..005890ff1e4b 100644
--- a/drivers/net/dsa/realtek-smi-core.h
+++ b/drivers/net/dsa/realtek-smi-core.h
@@ -144,5 +144,6 @@ int rtl8366_get_sset_count(struct dsa_switch *ds, int port, int sset);
void rtl8366_get_ethtool_stats(struct dsa_switch *ds, int port, uint64_t *data);
extern const struct realtek_smi_variant rtl8366rb_variant;
+extern const struct realtek_smi_variant rtl8365mb_variant;
#endif /* _REALTEK_SMI_H */
diff --git a/drivers/net/dsa/rtl8365mb.c b/drivers/net/dsa/rtl8365mb.c
new file mode 100644
index 000000000000..7698c0e3e33e
--- /dev/null
+++ b/drivers/net/dsa/rtl8365mb.c
@@ -0,0 +1,2124 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Realtek SMI subdriver for the Realtek RTL8365MB-VC Ethernet switch.
+ *
+ * Copyright (C) 2021 Alvin Šipraga <alsi@xxxxxxxxxxxxxxx>
+ * Copyright (C) 2021 Michael Rasmussen <mir@xxxxxxxxxxxxxxx>
+ *
+ * The RTL8365MB-VC is a 4+1 port 10/100/1000M switch controller. It includes 4
+ * integrated PHYs for the user facing ports, and an extension interface which
+ * can be connected to the CPU - or another PHY - via either MII, RMII, or
+ * RGMII. The switch is configured via the Realtek Simple Management Interface
+ * (SMI), which uses the MDIO/MDC lines.
+ *
+ * Below is a simplified block diagram of the chip and its relevant interfaces.
+ *
+ * .-----------------------------------.
+ * | |
+ * UTP <---------------> Giga PHY <-> PCS <-> P0 GMAC |
+ * UTP <---------------> Giga PHY <-> PCS <-> P1 GMAC |
+ * UTP <---------------> Giga PHY <-> PCS <-> P2 GMAC |
+ * UTP <---------------> Giga PHY <-> PCS <-> P3 GMAC |
+ * | |
+ * CPU/PHY <-MII/RMII/RGMII---> Extension <---> Extension |
+ * | interface 1 GMAC 1 |
+ * | |
+ * SMI driver/ <-MDC/SCL---> Management ~~~~~~~~~~~~~~ |
+ * EEPROM <-MDIO/SDA--> interface ~REALTEK ~~~~~ |
+ * | ~RTL8365MB ~~~ |
+ * | ~GXXXC TAIWAN~ |
+ * GPIO <--------------> Reset ~~~~~~~~~~~~~~ |
+ * | |
+ * Interrupt <----------> Link UP/DOWN events |
+ * controller | |
+ * '-----------------------------------'
+ *
+ * The driver uses DSA to integrate the 4 user and 1 extension ports into the
+ * kernel. Netdevices are created for the user ports, as are PHY devices for
+ * their integrated PHYs. The device tree firmware should also specify the link
+ * partner of the extension port - either via a fixed-link or other phy-handle.
+ * See the device tree bindings for more detailed information. Note that the
+ * driver has only been tested with a fixed-link, but in principle it should not
+ * matter.
+ *
+ * NOTE: Currently, only the RGMII interface is implemented in this driver.
+ *
+ * The interrupt line is asserted on link UP/DOWN events. The driver creates a
+ * custom irqchip to handle this interrupt and demultiplex the events by reading
+ * the status registers via SMI. Interrupts are then propagated to the relevant
+ * PHY device.
+ *
+ * The EEPROM contains initial register values which the chip will read over I2C
+ * upon hardware reset. It is also possible to omit the EEPROM. In both cases,
+ * the driver will manually reprogram some registers using jam tables to reach
+ * an initial state defined by the vendor driver.
+ *
+ * This Linux driver is written based on an OS-agnostic vendor driver from
+ * Realtek. The reference GPL-licensed sources can be found in the OpenWrt
+ * source tree under the name rtl8367c. The vendor driver claims to support a
+ * number of similar switch controllers from Realtek, but the only hardware we
+ * have is the RTL8365MB-VC. Moreover, there does not seem to be any chip under
+ * the name RTL8367C. Although one wishes that the 'C' stood for some kind of
+ * common hardware revision, there exist examples of chips with the suffix -VC
+ * which are explicitly not supported by the rtl8367c driver and which instead
+ * require the rtl8367d vendor driver. With all this uncertainty, the driver has
+ * been modestly named rtl8365mb. Future implementors may wish to rename things
+ * accordingly.
+ *
+ * In the same family of chips, some carry up to 8 user ports and up to 2
+ * extension ports. Where possible this driver tries to make things generic, but
+ * more work must be done to support these configurations. According to
+ * documentation from Realtek, the family should include the following chips:
+ *
+ * - RTL8363NB
+ * - RTL8363NB-VB
+ * - RTL8363SC
+ * - RTL8363SC-VB
+ * - RTL8364NB
+ * - RTL8364NB-VB
+ * - RTL8365MB-VC
+ * - RTL8366SC
+ * - RTL8367RB-VB
+ * - RTL8367SB
+ * - RTL8367S
+ * - RTL8370MB
+ * - RTL8310SR
+ *
+ * Some of the register logic for these additional chips has been skipped over
+ * while implementing this driver. It is therefore not possible to assume that
+ * things will work out-of-the-box for other chips, and a careful review of the
+ * vendor driver may be needed to expand support. The RTL8365MB-VC seems to be
+ * one of the simpler chips.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/interrupt.h>
+#include <linux/irqdomain.h>
+#include <linux/of_irq.h>
+#include <linux/regmap.h>
+
+#include "realtek-smi-core.h"
+
+/* Port mapping macros
+ *
+ * PORT_NUM_x2y: map a port number from domain x to domain y
+ * PORT_MASK_x2y: map a port mask from domain x to domain y
+ *
+ * L = logical port domain, i.e. dsa_port.index
+ * P = physical port domain, used by the Realtek ASIC for port indexing;
+ * for ports with internal PHYs, this is also the PHY index
+ * E = extension port domain, used by the Realtek ASIC for managing EXT ports
+ *
+ * The terminology is borrowed from the vendor driver. The extension port domain
+ * is mostly used to navigate the labyrinthine layout of EXT port configuration
+ * registers and is not considered intuitive by the author.
+ *
+ * Unless a function is accessing chip registers, it should be using the logical
+ * port domain. Moreover, function arguments for port numbers and port masks
+ * must always be in the logical domain. The conversion must be done as close as
+ * possible to the register access to avoid chaos.
+ *
+ * The mappings vary between chips in the family supported by this driver. Here
+ * is an example of the mapping for the RTL8365MB-VC:
+ *
+ * L | P | E | remark
+ * ---+---+---+--------
+ * 0 | 0 | | user port
+ * 1 | 1 | | user port
+ * 2 | 2 | | user port
+ * 3 | 3 | | user port
+ * 4 | 6 | 1 | extension (CPU) port
+ *
+ * NOTE: Currently this is hardcoded for the RTL8365MB-VC. This will probably
+ * require a rework when adding support for other chips.
+ */
+#define CPU_PORT_LOGICAL_NUM 4
+#define CPU_PORT_LOGICAL_MASK BIT(CPU_PORT_LOGICAL_NUM)
+#define CPU_PORT_PHYSICAL_NUM 6
+#define CPU_PORT_PHYSICAL_MASK BIT(CPU_PORT_PHYSICAL_NUM)
+#define CPU_PORT_EXTENSION_NUM 1
+
+#define PORT_NUM_L2P(_p) \
+ ((_p) == CPU_PORT_LOGICAL_NUM ? CPU_PORT_PHYSICAL_NUM : (_p))
+#define PORT_NUM_P2L(_p) \
+ ((_p) == CPU_PORT_PHYSICAL_NUM ? CPU_PORT_LOGICAL_NUM : (_p))
+#define PORT_NUM_L2E(_p) (CPU_PORT_EXTENSION_NUM)
+
+#define PORT_MASK_L2P(_m) \
+ (((_m) & ~CPU_PORT_LOGICAL_MASK) | \
+ (((_m) & CPU_PORT_LOGICAL_MASK) ? CPU_PORT_PHYSICAL_MASK : 0))
+#define PORT_MASK_P2L(_m) \
+ (((_m) & ~CPU_PORT_PHYSICAL_MASK) | \
+ (((_m) & CPU_PORT_PHYSICAL_MASK) ? CPU_PORT_LOGICAL_MASK : 0))
+
+/* Chip-specific data and limits */
+#define RTL8365MB_CHIP_ID_8365MB_VC 0x6367
+#define RTL8365MB_NUM_PORTS_8365MB_VC 5
+#define RTL8365MB_NUM_PHYS_8365MB_VC 4
+#define RTL8365MB_CPU_PORT_NUM_8365MB_VC 4
+#define RTL8365MB_CPU_PORT_MASK_8365MB_VC BIT(4)
+#define RTL8365MB_PHY_PORT_MASK_8365MB_VC GENMASK(3, 0)
+#define RTL8365MB_PORT_MASK_8365MB_VC \
+ (RTL8365MB_CPU_PORT_MASK_8365MB_VC | \
+ RTL8365MB_PHY_PORT_MASK_8365MB_VC)
+
+/* Family-specific data and limits */
+#define RTL8365MB_NUM_PHYREGS 32
+#define RTL8365MB_PHYREGMAX (RTL8365MB_NUM_PHYREGS - 1)
+#define RTL8365MB_NUM_VLANS 32
+#define RTL8365MB_NUM_VIDS 4096
+#define RTL8365MB_VIDMAX (RTL8365MB_NUM_VIDS - 1)
+#define RTL8365MB_NUM_EVIDS 8192
+#define RTL8365MB_EVIDMAX (RTL8365MB_NUM_EVIDS - 1)
+#define RTL8365MB_PRIORITYMAX 7
+#define RTL8365MB_FIDMAX 15
+#define RTL8365MB_NUM_METERS 64
+#define RTL8365MB_METERMAX (RTL8365MB_NUM_METERS - 1)
+
+/* Chip identification registers */
+#define RTL8365MB_CHIP_ID_REG 0x1300
+
+#define RTL8365MB_CHIP_VER_REG 0x1301
+
+#define RTL8365MB_MAGIC_REG 0x13C2
+#define RTL8365MB_MAGIC_VALUE 0x0249
+
+/* Chip reset register */
+#define RTL8365MB_CHIP_RESET_REG 0x1322
+#define RTL8365MB_CHIP_RESET_SW_MASK 0x0002
+#define RTL8365MB_CHIP_RESET_HW_MASK 0x0001
+
+/* Interrupt polarity register */
+#define RTL8365MB_INTR_POLARITY_REG 0x1100
+#define RTL8365MB_INTR_POLARITY_MASK 0x0001
+#define RTL8365MB_INTR_POLARITY_HIGH 0
+#define RTL8365MB_INTR_POLARITY_LOW 1
+
+/* Interrupt control register - enable or disable specific interrupt types */
+#define RTL8365MB_INTR_CTRL 0x1101
+#define RTL8365MB_INTR_CTRL_SLIENT_START_2_MASK 0x1000
+#define RTL8365MB_INTR_CTRL_SLIENT_START_MASK 0x800
+#define RTL8365MB_INTR_CTRL_ACL_ACTION_MASK 0x200
+#define RTL8365MB_INTR_CTRL_CABLE_DIAG_FIN_MASK 0x100
+#define RTL8365MB_INTR_CTRL_INTERRUPT_8051_MASK 0x80
+#define RTL8365MB_INTR_CTRL_LOOP_DETECTION_MASK 0x40
+#define RTL8365MB_INTR_CTRL_GREEN_TIMER_MASK 0x20
+#define RTL8365MB_INTR_CTRL_SPECIAL_CONGEST_MASK 0x10
+#define RTL8365MB_INTR_CTRL_SPEED_CHANGE_MASK 0x8
+#define RTL8365MB_INTR_CTRL_LEARN_OVER_MASK 0x4
+#define RTL8365MB_INTR_CTRL_METER_EXCEEDED_MASK 0x2
+#define RTL8365MB_INTR_CTRL_LINK_CHANGE_MASK 0x1
+
+
+/* Interrupt status register */
+#define RTL8365MB_INTR_STATUS_REG 0x1102
+#define RTL8365MB_INTR_STATUS_SLIENT_START_2_MASK 0x1000
+#define RTL8365MB_INTR_STATUS_SLIENT_START_MASK 0x800
+#define RTL8365MB_INTR_STATUS_ACL_ACTION_MASK 0x200
+#define RTL8365MB_INTR_STATUS_CABLE_DIAG_FIN_MASK 0x100
+#define RTL8365MB_INTR_STATUS_INTERRUPT_8051_MASK 0x80
+#define RTL8365MB_INTR_STATUS_LOOP_DETECTION_MASK 0x40
+#define RTL8365MB_INTR_STATUS_GREEN_TIMER_MASK 0x20
+#define RTL8365MB_INTR_STATUS_SPECIAL_CONGEST_MASK 0x10
+#define RTL8365MB_INTR_STATUS_SPEED_CHANGE_MASK 0x8
+#define RTL8365MB_INTR_STATUS_LEARN_OVER_MASK 0x4
+#define RTL8365MB_INTR_STATUS_METER_EXCEEDED_MASK 0x2
+#define RTL8365MB_INTR_STATUS_LINK_CHANGE_MASK 0x1
+#define RTL8365MB_INTR_STATUS_ALL_MASK \
+ (RTL8365MB_INTR_STATUS_SLIENT_START_2_MASK | \
+ RTL8365MB_INTR_STATUS_SLIENT_START_MASK | \
+ RTL8365MB_INTR_STATUS_ACL_ACTION_MASK | \
+ RTL8365MB_INTR_STATUS_CABLE_DIAG_FIN_MASK | \
+ RTL8365MB_INTR_STATUS_INTERRUPT_8051_MASK | \
+ RTL8365MB_INTR_STATUS_LOOP_DETECTION_MASK | \
+ RTL8365MB_INTR_STATUS_GREEN_TIMER_MASK | \
+ RTL8365MB_INTR_STATUS_SPECIAL_CONGEST_MASK | \
+ RTL8365MB_INTR_STATUS_SPEED_CHANGE_MASK | \
+ RTL8365MB_INTR_STATUS_LEARN_OVER_MASK | \
+ RTL8365MB_INTR_STATUS_METER_EXCEEDED_MASK | \
+ RTL8365MB_INTR_STATUS_LINK_CHANGE_MASK)
+
+/* Per-port interrupt type status registers */
+#define RTL8365MB_PORT_LINKDOWN_IND_REG 0x1106
+#define RTL8365MB_PORT_LINKDOWN_IND_MASK 0x7FF
+
+#define RTL8365MB_PORT_LINKUP_IND_REG 0x1107
+#define RTL8365MB_PORT_LINKUP_IND_MASK 0x7FF
+
+/* PHY indirect access registers */
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_REG 0x1F00
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK 0x0002
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ 0
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE 1
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK 0x1
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE 1
+#define RTL8365MB_INDIRECT_ACCESS_STATUS_REG 0x1F01
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG 0x1F02
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK GENMASK(4, 0)
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK GENMASK(6, 5)
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK GENMASK(11, 8)
+#define RTL8365MB_PHY_BASE 0x2000
+#define RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG 0x1F03
+#define RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG 0x1F04
+
+/* PHY OCP address prefix register */
+#define RTL8365MB_GPHY_OCP_MSB_0_REG 0x1D15
+#define RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK 0x0FC0
+#define RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK 0xFC00
+
+/* The PHY OCP addresses of PHY registers 0~31 start here */
+#define RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE 0xA400
+
+/* EXT port interface mode values - used in DIGITAL_INTERFACE_SELECT */
+#define RTL8365MB_EXT_PORT_MODE_DISABLE 0
+#define RTL8365MB_EXT_PORT_MODE_RGMII 1
+#define RTL8365MB_EXT_PORT_MODE_MII_MAC 2
+#define RTL8365MB_EXT_PORT_MODE_MII_PHY 3
+#define RTL8365MB_EXT_PORT_MODE_TMII_MAC 4
+#define RTL8365MB_EXT_PORT_MODE_TMII_PHY 5
+#define RTL8365MB_EXT_PORT_MODE_GMII 6
+#define RTL8365MB_EXT_PORT_MODE_RMII_MAC 7
+#define RTL8365MB_EXT_PORT_MODE_RMII_PHY 8
+#define RTL8365MB_EXT_PORT_MODE_SGMII 9
+#define RTL8365MB_EXT_PORT_MODE_HSGMII 10
+#define RTL8365MB_EXT_PORT_MODE_1000X_100FX 11
+#define RTL8365MB_EXT_PORT_MODE_1000X 12
+#define RTL8365MB_EXT_PORT_MODE_100FX 13
+
+/* EXT port interface mode configuration registers 0~1 */
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 0x1305
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 0x13C3
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(_extport) \
+ (RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 + \
+ ((_extport) >> 1) * (0x13C3 - 0x1305))
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(_extport) \
+ (0xF << (((_extport) % 2)))
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(_extport) \
+ (((_extport) % 2) * 4)
+
+/* EXT port RGMII TX/RX delay configuration registers 1~2 */
+#define RTL8365MB_EXT_RGMXF_REG1 0x1307
+#define RTL8365MB_EXT_RGMXF_REG2 0x13C5
+#define RTL8365MB_EXT_RGMXF_REG(_extport) \
+ (RTL8365MB_EXT_RGMXF_REG1 + \
+ (((_extport) >> 1) * (0x13C5 - 0x1307)))
+#define RTL8365MB_EXT_RGMXF_RXDELAY_MASK 0x0007
+#define RTL8365MB_EXT_RGMXF_TXDELAY_MASK 0x0008
+
+/* External port speed values - used in DIGITAL_INTERFACE_FORCE */
+#define RTL8365MB_PORT_SPEED_10M 0
+#define RTL8365MB_PORT_SPEED_100M 1
+#define RTL8365MB_PORT_SPEED_1000M 2
+
+/* EXT port force configuration registers 0~2 */
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 0x1310
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 0x1311
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 0x13c4
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(_extport) \
+ (RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 + \
+ ((_extport) & 0x1) + \
+ ((((_extport) >> 1) & 0x1) * (0x13C4 - 0x1310)))
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK 0x1000
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_NWAY_MASK 0x0080
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK 0x0040
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK 0x0020
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK 0x0010
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK 0x0004
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK 0x0003
+
+/* CPU port mask register - controls which ports are treated as CPU ports */
+#define RTL8365MB_CPU_PORT_MASK_REG 0x1219
+#define RTL8365MB_CPU_PORT_MASK_MASK 0x07FF
+
+/* CPU control register */
+#define RTL8365MB_CPU_CTRL_REG 0x121a
+#define RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK 0x400
+#define RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK 0x200
+#define RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK 0x80
+#define RTL8365MB_CPU_CTRL_TAG_POSITION_MASK 0x40
+#define RTL8365MB_CPU_CTRL_TRAP_PORT_MASK 0x38
+#define RTL8365MB_CPU_CTRL_INSERTMODE_MASK 0x6
+#define RTL8365MB_CPU_CTRL_EN_MASK 0x1
+
+/* Maximum packet length register */
+#define RTL8365MB_CFG0_MAX_LEN_REG 0x088c
+#define RTL8365MB_CFG0_MAX_LEN_MASK 0x3FFF
+
+/* Table read/write registers */
+#define RTL8365MB_TABLE_READ_BASE 0x0520
+#define RTL8365MB_TABLE_READ_REG(_x) \
+ (RTL8365MB_TABLE_READ_BASE + (_x))
+#define RTL8365MB_TABLE_WRITE_BASE 0x0510
+#define RTL8365MB_TABLE_WRITE_REG(_x) \
+ (RTL8365MB_TABLE_WRITE_BASE + (_x))
+/* The generic table size is actually 10, but the uppermost table register has
+ * space for only half a word (1 byte). There doesn't seem to be any table with
+ * such large entries, so cap it at 9 to simplify the read/write logic below.
+ */
+#define RTL8365MB_TABLE_ENTRY_SIZE 9
+
+/* Table access control register
+ * NOTE: Some tables seem to support alternative access methods. For now the
+ * method field is not used by rtl8365mb_table_{read,write}.
+ */
+#define RTL8365MB_TABLE_ACCESS_CTRL_REG 0x0500
+#define RTL8365MB_TABLE_ACCESS_CTRL_TARGET_MASK 0x0007
+#define RTL8365MB_TABLE_ACCESS_CTRL_TARGET_ACLRULE 1
+#define RTL8365MB_TABLE_ACCESS_CTRL_TARGET_ACLACT 2
+#define RTL8365MB_TABLE_ACCESS_CTRL_TARGET_CVLAN 3
+#define RTL8365MB_TABLE_ACCESS_CTRL_TARGET_L2 4
+#define RTL8365MB_TABLE_ACCESS_CTRL_TARGET_IGMP_GROUP 5
+#define RTL8365MB_TABLE_ACCESS_CTRL_CMD_TYPE_MASK 0x0008
+#define RTL8365MB_TABLE_ACCESS_CTRL_CMD_TYPE_READ 0
+#define RTL8365MB_TABLE_ACCESS_CTRL_CMD_TYPE_WRITE 1
+#define RTL8365MB_TABLE_ACCESS_CTRL_METHOD_MASK 0x0070
+
+/* Table access address register */
+#define RTL8365MB_TABLE_ACCESS_ADDR_REG 0x0501
+#define RTL8365MB_TABLE_ACCESS_ADDR_MASK 0x1FFF
+
+/* Table LUT (look-up-table) address register */
+#define RTL8365MB_TABLE_LUT_ADDR_REG 0x0502
+#define RTL8365MB_TABLE_LUT_ADDR_ADDRESS2_MASK 0x4000
+#define RTL8365MB_TABLE_LUT_ADDR_BUSY_FLAG_MASK 0x2000
+#define RTL8365MB_TABLE_LUT_ADDR_HIT_STATUS_MASK 0x1000
+#define RTL8365MB_TABLE_LUT_ADDR_TYPE_MASK 0x0800
+#define RTL8365MB_TABLE_LUT_ADDR_ADDRESS_MASK 0x07FF
+
+/* CVLAN (i.e. vlan4k) table entry layout, u16[4] */
+#define RTL8365MB_CVLAN_ENTRY_D0_MBR_MASK 0x00FF
+#define RTL8365MB_CVLAN_ENTRY_D0_UNTAG_MASK 0xFF00
+#define RTL8365MB_CVLAN_ENTRY_D1_FID_MASK 0x000F
+#define RTL8365MB_CVLAN_ENTRY_D1_VBPEN_MASK 0x0010
+#define RTL8365MB_CVLAN_ENTRY_D1_VBPRI_MASK 0x00E0
+#define RTL8365MB_CVLAN_ENTRY_D1_ENVLANPOL_MASK 0x0100
+#define RTL8365MB_CVLAN_ENTRY_D1_METERIDX_MASK 0x3E00
+#define RTL8365MB_CVLAN_ENTRY_D1_IVL_SVL_MASK 0x4000
+#define RTL8365MB_CVLAN_ENTRY_D2_MBR_EXT_MASK 0x0007
+#define RTL8365MB_CVLAN_ENTRY_D2_UNTAG_EXT_MASK 0x0038
+#define RTL8365MB_CVLAN_ENTRY_D2_METERIDX_EXT_MASK 0x0040
+
+/* Port isolation (forwarding mask) registers */
+#define RTL8365MB_PORT_ISOLATION_REG_BASE 0x08A2
+#define RTL8365MB_PORT_ISOLATION_REG(_physport) \
+ (RTL8365MB_PORT_ISOLATION_REG_BASE + (_physport))
+#define RTL8365MB_PORT_ISOLATION_MASK 0x07FF
+
+/* Port-based VID registers 0~5 - each one holds an MC index for two ports */
+#define RTL8365MB_VLAN_PVID_CTRL_BASE 0x0700
+
+#define RTL8365MB_VLAN_PVID_CTRL_REG(_physport) \
+ (RTL8365MB_VLAN_PVID_CTRL_BASE + ((_physport) >> 1))
+#define RTL8365MB_VLAN_PVID_CTRL_PORT0_VIDX_MASK 0x001F
+#define RTL8365MB_VLAN_PVID_CTRL_PORT1_VIDX_MASK 0x1F00
+#define RTL8365MB_VLAN_PVID_CTRL_PORT_VIDX_OFFSET(_physport) \
+ (((_physport) & 1) << 3)
+#define RTL8365MB_VLAN_PVID_CTRL_PORT_VIDX_MASK(_physport) \
+ (0x1F << RTL8365MB_VLAN_PVID_CTRL_PORT_VIDX_OFFSET(_physport))
+
+/* VLAN control register */
+#define RTL8365MB_VLAN_CTRL_REG 0x07A8
+#define RTL8365MB_VLAN_CTRL_EN_MASK 0x0001
+
+/* VLAN ingress filter register - enable ingress filter on masked ports */
+#define RTL8365MB_VLAN_INGRESS_REG 0x07A9
+#define RTL8365MB_VLAN_INGRESS_FILTER_PORT_EN_OFFSET(_physport) (_physport)
+#define RTL8365MB_VLAN_INGRESS_FILTER_PORT_EN_MASK(_physport) BIT(_physport)
+
+/* VLAN member configuration registers 0~31, u16[3] */
+#define RTL8365MB_VLAN_MC_BASE 0x0728
+#define RTL8365MB_VLAN_MC_REG(_x) \
+ (RTL8365MB_VLAN_MC_BASE + (_x) * 4)
+#define RTL8365MB_VLAN_MC_D0_MBR_MASK 0x07FF
+#define RTL8365MB_VLAN_MC_D1_FID_MASK 0x000F
+#define RTL8365MB_VLAN_MC_D2_METERIDX_MASK 0x07E0
+#define RTL8365MB_VLAN_MC_D2_ENVLANPOL_MASK 0x0010
+#define RTL8365MB_VLAN_MC_D2_VBPRI_MASK 0x000E
+#define RTL8365MB_VLAN_MC_D2_VBPEN_MASK 0x0001
+#define RTL8365MB_VLAN_MC_D3_EVID_MASK 0x1FFF
+
+enum rtl8365mb_table {
+ RTL8365MB_TABLE_ACLRULE = RTL8365MB_TABLE_ACCESS_CTRL_TARGET_ACLRULE,
+ RTL8365MB_TABLE_ACLACT = RTL8365MB_TABLE_ACCESS_CTRL_TARGET_ACLACT,
+ RTL8365MB_TABLE_CVLAN = RTL8365MB_TABLE_ACCESS_CTRL_TARGET_CVLAN,
+ RTL8365MB_TABLE_L2 = RTL8365MB_TABLE_ACCESS_CTRL_TARGET_L2,
+ RTL8365MB_TABLE_IGMP_GROUP =
+ RTL8365MB_TABLE_ACCESS_CTRL_TARGET_IGMP_GROUP,
+};
+
+/* MIB counter value registers */
+#define RTL8365MB_MIB_COUNTER_BASE 0x1000
+#define RTL8365MB_MIB_COUNTER_REG(_x) (RTL8365MB_MIB_COUNTER_BASE + (_x))
+
+/* MIB counter address register */
+#define RTL8365MB_MIB_ADDRESS_REG 0x1004
+#define RTL8365MB_MIB_ADDRESS_PORT_OFFSET 0x7C
+#define RTL8365MB_MIB_ADDRESS(_p, _x) \
+ (((RTL8365MB_MIB_ADDRESS_PORT_OFFSET) * (_p) + (_x)) >> 2)
+
+#define RTL8365MB_MIB_CTRL0_REG 0x1005
+#define RTL8365MB_MIB_CTRL0_RESET_FLAG_MASK 0x2
+#define RTL8365MB_MIB_CTRL0_BUSY_FLAG_MASK 0x0001
+
+static struct rtl8366_mib_counter rtl8365mb_mib_counters[] = {
+ { 0, 0, 4, "ifInOctets" },
+ { 0, 4, 2, "dot3StatsFCSErrors" },
+ { 0, 6, 2, "dot3StatsSymbolErrors" },
+ { 0, 8, 2, "dot3InPauseFrames" },
+ { 0, 10, 2, "dot3ControlInUnknownOpcodes" },
+ { 0, 12, 2, "etherStatsFragments" },
+ { 0, 14, 2, "etherStatsJabbers" },
+ { 0, 16, 2, "ifInUcastPkts" },
+ { 0, 18, 2, "etherStatsDropEvents" },
+ { 0, 20, 2, "ifInMulticastPkts" },
+ { 0, 22, 2, "ifInBroadcastPkts" },
+ { 0, 24, 2, "inMldChecksumError" },
+ { 0, 26, 2, "inIgmpChecksumError" },
+ { 0, 28, 2, "inMldSpecificQuery" },
+ { 0, 30, 2, "inMldGeneralQuery" },
+ { 0, 32, 2, "inIgmpSpecificQuery" },
+ { 0, 34, 2, "inIgmpGeneralQuery" },
+ { 0, 36, 2, "inMldLeaves" },
+ { 0, 38, 2, "inIgmpLeaves" },
+ { 0, 40, 4, "etherStatsOctets" },
+ { 0, 44, 2, "etherStatsUnderSizePkts" },
+ { 0, 46, 2, "etherOversizeStats" },
+ { 0, 48, 2, "etherStatsPkts64Octets" },
+ { 0, 50, 2, "etherStatsPkts65to127Octets" },
+ { 0, 52, 2, "etherStatsPkts128to255Octets" },
+ { 0, 54, 2, "etherStatsPkts256to511Octets" },
+ { 0, 56, 2, "etherStatsPkts512to1023Octets" },
+ { 0, 58, 2, "etherStatsPkts1024to1518Octets" },
+ { 0, 60, 4, "ifOutOctets" },
+ { 0, 64, 2, "dot3StatsSingleCollisionFrames" },
+ { 0, 66, 2, "dot3StatMultipleCollisionFrames" },
+ { 0, 68, 2, "dot3sDeferredTransmissions" },
+ { 0, 70, 2, "dot3StatsLateCollisions" },
+ { 0, 72, 2, "etherStatsCollisions" },
+ { 0, 74, 2, "dot3StatsExcessiveCollisions" },
+ { 0, 76, 2, "dot3OutPauseFrames" },
+ { 0, 78, 2, "ifOutDiscards" },
+ { 0, 80, 2, "dot1dTpPortInDiscards" },
+ { 0, 82, 2, "ifOutUcastPkts" },
+ { 0, 84, 2, "ifOutMulticastPkts" },
+ { 0, 86, 2, "ifOutBroadcastPkts" },
+ { 0, 88, 2, "outOampduPkts" },
+ { 0, 90, 2, "inOampduPkts" },
+ { 0, 92, 4, "inIgmpJoinsSuccess" },
+ { 0, 96, 2, "inIgmpJoinsFail" },
+ { 0, 98, 2, "inMldJoinsSuccess" },
+ { 0, 100, 2, "inMldJoinsFail" },
+ { 0, 102, 2, "inReportSuppressionDrop" },
+ { 0, 104, 2, "inLeaveSuppressionDrop" },
+ { 0, 106, 2, "outIgmpReports" },
+ { 0, 108, 2, "outIgmpLeaves" },
+ { 0, 110, 2, "outIgmpGeneralQuery" },
+ { 0, 112, 2, "outIgmpSpecificQuery" },
+ { 0, 114, 2, "outMldReports" },
+ { 0, 116, 2, "outMldLeaves" },
+ { 0, 118, 2, "outMldGeneralQuery" },
+ { 0, 120, 2, "outMldSpecificQuery" },
+ { 0, 122, 2, "inKnownMulticastPkts" },
+};
+
+struct rtl8365mb_vlan_mc {
+ u16 evid;
+ u16 member;
+ u8 fid;
+ u8 priority;
+ u8 priority_en : 1;
+ u8 policing_en : 1;
+ u16 meteridx;
+};
+
+struct rtl8365mb_vlan_4k {
+ u16 vid;
+ u16 member;
+ u16 untag;
+ u8 fid;
+ u8 priority;
+ u8 priority_en : 1;
+ u8 policing_en : 1;
+ u8 ivl_en : 1;
+ u8 meteridx;
+};
+
+struct rtl8365mb_jam_tbl_entry {
+ u16 reg;
+ u16 val;
+};
+
+/* Lifted from the vendor driver sources */
+static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_8365mb_vc[] = {
+ { 0x13EB, 0x15BB }, { 0x1303, 0x06D6 }, { 0x1304, 0x0700 },
+ { 0x13E2, 0x003F }, { 0x13F9, 0x0090 }, { 0x121E, 0x03CA },
+ { 0x1233, 0x0352 }, { 0x1237, 0x00A0 }, { 0x123A, 0x0030 },
+ { 0x1239, 0x0084 }, { 0x0301, 0x1000 }, { 0x1349, 0x001F },
+ { 0x18E0, 0x4004 }, { 0x122B, 0x241C }, { 0x1305, 0xC000 },
+ { 0x13F0, 0x0000 },
+};
+
+static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_common[] = {
+ { 0x1200, 0x7FCB }, { 0x0884, 0x0003 }, { 0x06EB, 0x0001 },
+ { 0x03Fa, 0x0007 }, { 0x08C8, 0x00C0 }, { 0x0A30, 0x020E },
+ { 0x0800, 0x0000 }, { 0x0802, 0x0000 }, { 0x09DA, 0x0013 },
+ { 0x1D32, 0x0002 },
+};
+
+enum rtl8365mb_cpu_insert {
+ RTL8365MB_CPU_INSERT_TO_ALL = 0,
+ RTL8365MB_CPU_INSERT_TO_TRAPPING = 1,
+ RTL8365MB_CPU_INSERT_TO_NONE = 2,
+};
+
+enum rtl8365mb_cpu_position {
+ RTL8365MB_CPU_POS_AFTER_SA = 0,
+ RTL8365MB_CPU_POS_BEFORE_CRC = 1,
+};
+
+enum rtl8365mb_cpu_format {
+ RTL8365MB_CPU_FORMAT_8BYTES = 0,
+ RTL8365MB_CPU_FORMAT_4BYTES = 1,
+};
+
+enum rtl8365mb_cpu_rxlen {
+ RTL8365MB_CPU_RXLEN_72BYTES = 0,
+ RTL8365MB_CPU_RXLEN_64BYTES = 1,
+};
+
+struct rtl8365mb_cpu {
+ bool enable; /* enable CPU tagging */
+ u32 mask; /* port mask of ports that should parse CPU tags */
+ u32 trap_port; /* forward trapped frames to this port */
+ enum rtl8365mb_cpu_insert insert; /* tag insertion mode */
+ enum rtl8365mb_cpu_position position; /* position of CPU tag in frame */
+ enum rtl8365mb_cpu_rxlen rx_length; /* minimum CPU RX length */
+ enum rtl8365mb_cpu_format format; /* CPU tag format */
+};
+
+/* Private chip-specific driver data */
+struct rtl8365mb {
+ int irq; /* registered IRQ or zero */
+ u32 chip_id;
+ u32 chip_ver;
+ unsigned int num_phys; /* number of integrated PHYs */
+ u32 port_mask; /* mask of all ports */
+ u32 phy_port_mask; /* mask of ports with integrated PHYs */
+ struct rtl8365mb_cpu cpu; /* CPU configuration */
+ const struct rtl8365mb_jam_tbl_entry *jam_table;
+ size_t jam_size;
+};
+
+static int rtl8365mb_table_poll_busy(struct realtek_smi *smi)
+{
+ u32 val;
+
+ return regmap_read_poll_timeout(
+ smi->map, RTL8365MB_TABLE_LUT_ADDR_REG, val,
+ (val & RTL8365MB_TABLE_LUT_ADDR_BUSY_FLAG_MASK) == 0, 10, 100);
+}
+
+static int rtl8365mb_table_read(struct realtek_smi *smi,
+ enum rtl8365mb_table target, u32 addr,
+ u16 *data, size_t size)
+{
+ u32 val;
+ int ret;
+ int i;
+
+ if (!FIELD_FIT(RTL8365MB_TABLE_ACCESS_ADDR_MASK, addr))
+ return -EINVAL;
+
+ if (size > RTL8365MB_TABLE_ENTRY_SIZE)
+ return -E2BIG;
+
+ ret = rtl8365mb_table_poll_busy(smi);
+ if (ret)
+ return ret;
+
+ /* Set read address */
+ ret = regmap_write(smi->map, RTL8365MB_TABLE_ACCESS_ADDR_REG,
+ FIELD_PREP(RTL8365MB_TABLE_ACCESS_ADDR_MASK, addr));
+ if (ret)
+ return ret;
+
+ /* Execute read operation */
+ ret = regmap_write_bits(
+ smi->map, RTL8365MB_TABLE_ACCESS_CTRL_REG,
+ RTL8365MB_TABLE_ACCESS_CTRL_TARGET_MASK |
+ RTL8365MB_TABLE_ACCESS_CTRL_CMD_TYPE_MASK,
+ FIELD_PREP(RTL8365MB_TABLE_ACCESS_CTRL_TARGET_MASK, target) |
+ FIELD_PREP(RTL8365MB_TABLE_ACCESS_CTRL_CMD_TYPE_MASK,
+ RTL8365MB_TABLE_ACCESS_CTRL_CMD_TYPE_READ));
+ if (ret)
+ return ret;
+
+ ret = rtl8365mb_table_poll_busy(smi);
+ if (ret)
+ return ret;
+
+ /* Read table entry */
+ for (i = 0; i < size; i++) {
+ ret = regmap_read(smi->map, RTL8365MB_TABLE_READ_REG(i), &val);
+ if (ret)
+ return ret;
+
+ data[i] = val & 0xFFFF;
+ }
+
+ return 0;
+}
+
+static int rtl8365mb_table_write(struct realtek_smi *smi,
+ enum rtl8365mb_table target, u32 addr,
+ u16 *data, size_t size)
+{
+ int ret;
+ int i;
+
+ if (!FIELD_FIT(RTL8365MB_TABLE_ACCESS_ADDR_MASK, addr))
+ return -EINVAL;
+
+ if (size > RTL8365MB_TABLE_ENTRY_SIZE)
+ return -E2BIG;
+
+ /* Write table entry */
+ for (i = 0; i < size; i++) {
+ ret = regmap_write(smi->map, RTL8365MB_TABLE_WRITE_REG(i),
+ data[i]);
+ if (ret)
+ return ret;
+ }
+
+ /* Set write address */
+ ret = regmap_write(smi->map, RTL8365MB_TABLE_ACCESS_ADDR_REG,
+ FIELD_PREP(RTL8365MB_TABLE_ACCESS_ADDR_MASK, addr));
+ if (ret)
+ return ret;
+
+ /* Execute write operation */
+ ret = regmap_write_bits(
+ smi->map, RTL8365MB_TABLE_ACCESS_CTRL_REG,
+ RTL8365MB_TABLE_ACCESS_CTRL_TARGET_MASK |
+ RTL8365MB_TABLE_ACCESS_CTRL_CMD_TYPE_MASK,
+ FIELD_PREP(RTL8365MB_TABLE_ACCESS_CTRL_TARGET_MASK, target) |
+ FIELD_PREP(RTL8365MB_TABLE_ACCESS_CTRL_CMD_TYPE_MASK,
+ RTL8365MB_TABLE_ACCESS_CTRL_CMD_TYPE_WRITE));
+
+ return ret;
+}
+
+static int rtl8365mb_phy_poll_busy(struct realtek_smi *smi)
+{
+ u32 val;
+
+ return regmap_read_poll_timeout(smi->map,
+ RTL8365MB_INDIRECT_ACCESS_STATUS_REG,
+ val, val == 0, 10, 100);
+}
+
+static int rtl8365mb_phy_ocp_prepare(struct realtek_smi *smi, int phy,
+ u32 ocp_addr)
+{
+ u32 val;
+ int ret;
+
+ /* Set OCP prefix */
+ val = FIELD_GET(RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK, ocp_addr);
+ ret = regmap_update_bits(
+ smi->map, RTL8365MB_GPHY_OCP_MSB_0_REG,
+ RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK,
+ FIELD_PREP(RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK, val));
+ if (ret)
+ return ret;
+
+ /* Set PHY register address */
+ val = RTL8365MB_PHY_BASE;
+ val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK, phy);
+ val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK,
+ ocp_addr >> 1);
+ val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK,
+ ocp_addr >> 6);
+ ret = regmap_write(smi->map, RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG,
+ val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_phy_ocp_read(struct realtek_smi *smi, int phy,
+ u32 ocp_addr, u16 *data)
+{
+ u32 val;
+ int ret;
+
+ ret = rtl8365mb_phy_poll_busy(smi);
+ if (ret)
+ return ret;
+
+ ret = rtl8365mb_phy_ocp_prepare(smi, phy, ocp_addr);
+ if (ret)
+ return ret;
+
+ /* Execute read operation */
+ val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) |
+ FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ);
+ ret = regmap_write(smi->map, RTL8365MB_INDIRECT_ACCESS_CTRL_REG, val);
+ if (ret)
+ return ret;
+
+ ret = rtl8365mb_phy_poll_busy(smi);
+ if (ret)
+ return ret;
+
+ /* Get PHY register data */
+ ret = regmap_read(smi->map, RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG,
+ &val);
+ if (ret)
+ return ret;
+
+ *data = val & 0xFFFF;
+
+ return 0;
+}
+
+static int rtl8365mb_phy_ocp_write(struct realtek_smi *smi, int phy,
+ u32 ocp_addr, u16 data)
+{
+ u32 val;
+ int ret;
+
+ ret = rtl8365mb_phy_poll_busy(smi);
+ if (ret)
+ return ret;
+
+ ret = rtl8365mb_phy_ocp_prepare(smi, phy, ocp_addr);
+ if (ret)
+ return ret;
+
+ /* Set PHY register data */
+ ret = regmap_write(smi->map, RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG,
+ data);
+ if (ret)
+ return ret;
+
+ /* Execute write operation */
+ val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) |
+ FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE);
+ ret = regmap_write(smi->map, RTL8365MB_INDIRECT_ACCESS_CTRL_REG, val);
+ if (ret)
+ return ret;
+
+ ret = rtl8365mb_phy_poll_busy(smi);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_phy_read(struct realtek_smi *smi, int phy, int regnum)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ u32 ocp_addr;
+ u16 val;
+ int ret;
+
+ if (phy >= mb->num_phys || regnum > RTL8365MB_PHYREGMAX)
+ return -EINVAL;
+
+ ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2;
+
+ ret = rtl8365mb_phy_ocp_read(smi, phy, ocp_addr, &val);
+ if (ret) {
+ dev_err(smi->dev,
+ "failed to read PHY%d reg %02x @ %04x, ret %d\n", phy,
+ regnum, ocp_addr, ret);
+ return ret;
+ }
+
+ dev_dbg(smi->dev, "read PHY%d register 0x%02x @ %04x, val <- %04x\n",
+ phy, regnum, ocp_addr, val);
+
+ return val;
+}
+
+static int rtl8365mb_phy_write(struct realtek_smi *smi, int phy, int regnum,
+ u16 val)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ u32 ocp_addr;
+ int ret;
+
+ if (phy >= mb->num_phys || regnum > RTL8365MB_PHYREGMAX)
+ return -EINVAL;
+
+ ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2;
+
+ ret = rtl8365mb_phy_ocp_write(smi, phy, ocp_addr, val);
+ if (ret) {
+ dev_err(smi->dev,
+ "failed to write PHY%d reg %02x @ %04x, ret %d\n", phy,
+ regnum, ocp_addr, ret);
+ return ret;
+ }
+
+ dev_dbg(smi->dev, "write PHY%d register 0x%02x @ %04x, val -> %04x\n",
+ phy, regnum, ocp_addr, val);
+
+ return 0;
+}
+
+static enum dsa_tag_protocol
+rtl8365mb_get_tag_protocol(struct dsa_switch *ds, int port,
+ enum dsa_tag_protocol mp)
+{
+ return DSA_TAG_PROTO_RTL8_4;
+}
+
+static int rtl8365mb_ext_config_rgmii(struct realtek_smi *smi, int port,
+ phy_interface_t interface)
+{
+ int tx_delay = 0;
+ int rx_delay = 0;
+ int ext_port;
+ int ret;
+
+ if (port == smi->cpu_port) {
+ ext_port = PORT_NUM_L2E(port);
+ } else {
+ dev_err(smi->dev, "only one EXT port is currently supported\n");
+ return -EINVAL;
+ }
+
+ /* Set the RGMII TX/RX delay
+ *
+ * The Realtek vendor driver indicates the following possible
+ * configuration settings:
+ *
+ * TX delay:
+ * 0 = no delay, 1 = 2 ns delay
+ * RX delay:
+ * 0 = no delay, 7 = maximum delay
+ * No units are specified, but there are a total of 8 steps.
+ *
+ * The vendor driver also states that this must be configured *before*
+ * forcing the external interface into a particular mode, which is done
+ * in the rtl8365mb_phylink_mac_link_{up,down} functions.
+ *
+ * NOTE: For now this is hardcoded to tx_delay = 1, rx_delay = 4.
+ */
+ if (interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ interface == PHY_INTERFACE_MODE_RGMII_TXID)
+ tx_delay = 1; /* 2 ns */
+
+ if (interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ interface == PHY_INTERFACE_MODE_RGMII_RXID)
+ rx_delay = 4;
+
+ ret = regmap_update_bits(
+ smi->map, RTL8365MB_EXT_RGMXF_REG(ext_port),
+ RTL8365MB_EXT_RGMXF_TXDELAY_MASK |
+ RTL8365MB_EXT_RGMXF_RXDELAY_MASK,
+ FIELD_PREP(RTL8365MB_EXT_RGMXF_TXDELAY_MASK, tx_delay) |
+ FIELD_PREP(RTL8365MB_EXT_RGMXF_RXDELAY_MASK, rx_delay));
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(
+ smi->map, RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(ext_port),
+ RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(ext_port),
+ RTL8365MB_EXT_PORT_MODE_RGMII
+ << RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(
+ ext_port));
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_ext_config_forcemode(struct realtek_smi *smi, int port,
+ bool link, int speed, int duplex,
+ bool tx_pause, bool rx_pause)
+{
+ u32 r_tx_pause;
+ u32 r_rx_pause;
+ u32 r_duplex;
+ u32 r_speed;
+ u32 r_link;
+ int ext_port;
+ int val;
+ int ret;
+
+ if (port == smi->cpu_port) {
+ ext_port = PORT_NUM_L2E(port);
+ } else {
+ dev_err(smi->dev, "only one EXT port is currently supported\n");
+ return -EINVAL;
+ }
+
+ if (link) {
+ /* Force the link up with the desired configuration */
+ r_link = 1;
+ r_rx_pause = rx_pause ? 1 : 0;
+ r_tx_pause = tx_pause ? 1 : 0;
+
+ if (speed == SPEED_1000) {
+ r_speed = RTL8365MB_PORT_SPEED_1000M;
+ } else if (speed == SPEED_100) {
+ r_speed = RTL8365MB_PORT_SPEED_100M;
+ } else if (speed == SPEED_10) {
+ r_speed = RTL8365MB_PORT_SPEED_10M;
+ } else {
+ dev_err(smi->dev, "unsupported port speed %s\n",
+ phy_speed_to_str(speed));
+ return -EINVAL;
+ }
+
+ if (duplex == DUPLEX_FULL) {
+ r_duplex = 1;
+ } else if (duplex == DUPLEX_HALF) {
+ r_duplex = 0;
+ } else {
+ dev_err(smi->dev, "unsupported duplex %s\n",
+ phy_duplex_to_str(duplex));
+ return -EINVAL;
+ }
+ } else {
+ /* Force the link down and reset any programmed configuration */
+ r_link = 0;
+ r_tx_pause = 0;
+ r_rx_pause = 0;
+ r_speed = 0;
+ r_duplex = 0;
+ }
+
+ val = FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK, 1) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK,
+ r_tx_pause) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK,
+ r_rx_pause) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK, r_link) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK,
+ r_duplex) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK, r_speed);
+ ret = regmap_write(
+ smi->map, RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(ext_port), val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static bool rtl8365mb_phy_mode_supported(struct dsa_switch *ds, int port,
+ phy_interface_t interface)
+{
+ if (dsa_is_user_port(ds, port) &&
+ (interface == PHY_INTERFACE_MODE_NA ||
+ interface == PHY_INTERFACE_MODE_INTERNAL))
+ /* Internal PHY */
+ return true;
+ else if (dsa_is_cpu_port(ds, port) &&
+ phy_interface_mode_is_rgmii(interface))
+ /* Extension MAC */
+ return true;
+
+ return false;
+}
+
+static void rtl8365mb_phylink_validate(struct dsa_switch *ds, int port,
+ unsigned long *supported,
+ struct phylink_link_state *state)
+{
+ struct realtek_smi *smi = ds->priv;
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0 };
+
+ /* include/linux/phylink.h says:
+ * When @state->interface is %PHY_INTERFACE_MODE_NA, phylink
+ * expects the MAC driver to return all supported link modes.
+ */
+ if (state->interface != PHY_INTERFACE_MODE_NA &&
+ !rtl8365mb_phy_mode_supported(ds, port, state->interface)) {
+ dev_err(smi->dev, "phy mode %s is unsupported on port %d\n",
+ phy_modes(state->interface), port);
+ linkmode_zero(supported);
+ return;
+ }
+
+ phylink_set_port_modes(mask);
+
+ phylink_set(mask, Autoneg);
+ phylink_set(mask, Pause);
+ phylink_set(mask, Asym_Pause);
+
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+ phylink_set(mask, 1000baseT_Full);
+ phylink_set(mask, 1000baseT_Half);
+
+ linkmode_and(supported, supported, mask);
+ linkmode_and(state->advertising, state->advertising, mask);
+}
+
+static void rtl8365mb_phylink_mac_config(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ const struct phylink_link_state *state)
+{
+ struct realtek_smi *smi = ds->priv;
+ int ret;
+
+ if (!rtl8365mb_phy_mode_supported(ds, port, state->interface)) {
+ dev_err(smi->dev, "phy mode %s is unsupported on port %d\n",
+ phy_modes(state->interface), port);
+ return;
+ }
+
+ /* If port MAC is connected to an internal PHY, we have nothing to do */
+ if (dsa_is_user_port(ds, port))
+ return;
+
+ if (mode != MLO_AN_PHY && mode != MLO_AN_FIXED) {
+ dev_err(smi->dev,
+ "port %d supports only conventional PHY or fixed-link\n",
+ port);
+ return;
+ }
+
+ if (phy_interface_mode_is_rgmii(state->interface)) {
+ ret = rtl8365mb_ext_config_rgmii(smi, port, state->interface);
+ if (ret)
+ dev_err(smi->dev,
+ "failed to configure RGMII mode on port %d: %d\n",
+ port, ret);
+ return;
+ }
+
+ /* TODO: Implement MII and RMII modes, which the RTL8365MB-VC also
+ * supports
+ */
+}
+
+static void rtl8365mb_phylink_mac_link_down(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface)
+{
+ struct realtek_smi *smi = ds->priv;
+ int ret;
+
+ if (dsa_is_cpu_port(ds, port)) {
+ ret = rtl8365mb_ext_config_forcemode(smi, port, false, 0, 0,
+ false, false);
+ if (ret)
+ dev_err(smi->dev,
+ "failed to reset forced mode on port %d: %d\n",
+ port, ret);
+
+ return;
+ }
+}
+
+static void rtl8365mb_phylink_mac_link_up(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface,
+ struct phy_device *phydev, int speed,
+ int duplex, bool tx_pause,
+ bool rx_pause)
+{
+ struct realtek_smi *smi = ds->priv;
+ int ret;
+
+ if (dsa_is_cpu_port(ds, port)) {
+ ret = rtl8365mb_ext_config_forcemode(
+ smi, port, true, speed, duplex, tx_pause, rx_pause);
+ if (ret)
+ dev_err(smi->dev,
+ "failed to force mode on port %d: %d\n", port,
+ ret);
+
+ return;
+ }
+}
+
+static int rtl8365mb_port_enable(struct dsa_switch *ds, int port,
+ struct phy_device *phy)
+{
+ struct realtek_smi *smi = ds->priv;
+ int val;
+
+ if (dsa_is_user_port(ds, port)) {
+ /* Power up the internal PHY and restart autonegotiation */
+ val = rtl8365mb_phy_read(smi, port, MII_BMCR);
+ if (val < 0)
+ return val;
+
+ val &= ~BMCR_PDOWN;
+ val |= BMCR_ANRESTART;
+
+ return rtl8365mb_phy_write(smi, port, MII_BMCR, val);
+ }
+
+ return 0;
+}
+
+static void rtl8365mb_port_disable(struct dsa_switch *ds, int port)
+{
+ struct realtek_smi *smi = ds->priv;
+ int val;
+
+ if (dsa_is_user_port(ds, port)) {
+ /* Power down the internal PHY */
+ val = rtl8365mb_phy_read(smi, port, MII_BMCR);
+ if (val < 0)
+ return;
+
+ val |= BMCR_PDOWN;
+
+ rtl8365mb_phy_write(smi, port, MII_BMCR, val);
+
+ return;
+ }
+}
+
+int rtl8365mb_port_vlan_filtering(struct dsa_switch *ds, int port,
+ bool vlan_filtering,
+ struct netlink_ext_ack *extack)
+{
+ struct realtek_smi *smi = ds->priv;
+ u32 phys_port = PORT_NUM_L2P(port);
+ int ret;
+
+ dev_info(smi->dev, "%s filtering on port %d\n",
+ vlan_filtering ? "enable" : "disable", port);
+
+ /* vlan_filtering on: Discard VLAN tagged frames if the port is not a
+ * member of the VLAN with which the packet is associated. Untagged
+ * packets should also be discarded unless the port has a PVID
+ * programmed.
+ *
+ * vlan_filtering off: Accept all VLAN tagged frames, including
+ * untagged.
+ */
+ ret = regmap_update_bits(
+ smi->map, RTL8365MB_VLAN_INGRESS_REG,
+ RTL8365MB_VLAN_INGRESS_FILTER_PORT_EN_MASK(phys_port),
+ (vlan_filtering ? 1 : 0)
+ << RTL8365MB_VLAN_INGRESS_FILTER_PORT_EN_OFFSET(
+ phys_port));
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int _rtl8365mb_get_vlan_4k(struct realtek_smi *smi, u32 vid,
+ struct rtl8365mb_vlan_4k *vlan4k)
+{
+ u32 phys_member;
+ u32 phys_untag;
+ u16 data[3];
+ int ret;
+
+ if (vid > RTL8365MB_VIDMAX)
+ return -EINVAL;
+
+ ret = rtl8365mb_table_read(smi, RTL8365MB_TABLE_CVLAN, vid, data,
+ ARRAY_SIZE(data));
+ if (ret)
+ return ret;
+
+ memset(vlan4k, 0, sizeof(*vlan4k));
+
+ /* Unpack table entry */
+ vlan4k->vid = vid;
+ phys_member = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D0_MBR_MASK, data[0]) |
+ (FIELD_GET(RTL8365MB_CVLAN_ENTRY_D2_MBR_EXT_MASK, data[2])
+ << 8);
+ phys_untag =
+ FIELD_GET(RTL8365MB_CVLAN_ENTRY_D0_UNTAG_MASK, data[0]) |
+ (FIELD_GET(RTL8365MB_CVLAN_ENTRY_D2_UNTAG_EXT_MASK, data[2])
+ << 8);
+ vlan4k->member = PORT_MASK_P2L(phys_member);
+ vlan4k->untag = PORT_MASK_P2L(phys_untag);
+ vlan4k->fid = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_FID_MASK, data[1]);
+ vlan4k->priority_en =
+ FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_VBPEN_MASK, data[1]);
+ vlan4k->priority =
+ FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_VBPRI_MASK, data[1]);
+ vlan4k->policing_en =
+ FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_ENVLANPOL_MASK, data[1]);
+ vlan4k->meteridx =
+ FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_METERIDX_MASK, data[1]) |
+ (FIELD_GET(RTL8365MB_CVLAN_ENTRY_D2_METERIDX_EXT_MASK, data[2])
+ << 5);
+ vlan4k->ivl_en =
+ FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_IVL_SVL_MASK, data[1]);
+
+ return 0;
+}
+
+static int rtl8365mb_get_vlan_4k(struct realtek_smi *smi, u32 vid,
+ struct rtl8366_vlan_4k *vlan4k)
+{
+ struct rtl8365mb_vlan_4k vlan4k_65mb;
+ int ret;
+
+ ret = _rtl8365mb_get_vlan_4k(smi, vid, &vlan4k_65mb);
+ if (ret)
+ return ret;
+
+ memset(vlan4k, 0, sizeof(*vlan4k));
+
+ vlan4k->vid = vlan4k_65mb.vid;
+ vlan4k->untag = vlan4k_65mb.untag;
+ vlan4k->member = vlan4k_65mb.member;
+ vlan4k->fid = vlan4k_65mb.fid;
+
+ return 0;
+}
+
+static int _rtl8365mb_set_vlan_4k(struct realtek_smi *smi,
+ const struct rtl8365mb_vlan_4k *vlan4k)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ u16 data[3] = { 0 };
+ u32 phys_member;
+ u32 phys_untag;
+
+ if ((vlan4k->member & ~(mb->port_mask)) ||
+ (vlan4k->untag & ~(mb->port_mask)) ||
+ vlan4k->vid > RTL8365MB_VIDMAX || vlan4k->fid > RTL8365MB_FIDMAX ||
+ vlan4k->priority > RTL8365MB_PRIORITYMAX ||
+ vlan4k->meteridx > RTL8365MB_METERMAX)
+ return -EINVAL;
+
+ phys_member = PORT_MASK_L2P(vlan4k->member);
+ phys_untag = PORT_MASK_L2P(vlan4k->untag);
+
+ /* Pack table entry value */
+ data[0] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D0_MBR_MASK, phys_member);
+ data[0] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D0_UNTAG_MASK, phys_untag);
+ data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_FID_MASK, vlan4k->fid);
+ data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_VBPEN_MASK,
+ vlan4k->priority_en);
+ data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_VBPRI_MASK,
+ vlan4k->priority);
+ data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_ENVLANPOL_MASK,
+ vlan4k->policing_en);
+ data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_METERIDX_MASK,
+ vlan4k->meteridx);
+ data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_IVL_SVL_MASK,
+ vlan4k->ivl_en);
+ data[2] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D2_MBR_EXT_MASK,
+ phys_member >> 8);
+ data[2] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D2_UNTAG_EXT_MASK,
+ phys_untag >> 8);
+ data[2] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D2_METERIDX_EXT_MASK,
+ vlan4k->meteridx >> 5);
+
+ return rtl8365mb_table_write(smi, RTL8365MB_TABLE_CVLAN, vlan4k->vid,
+ data, ARRAY_SIZE(data));
+}
+
+static int rtl8365mb_set_vlan_4k(struct realtek_smi *smi,
+ const struct rtl8366_vlan_4k *vlan4k)
+{
+ struct rtl8365mb_vlan_4k vlan4k_65mb = { 0 };
+
+ /* The RTL8365MB-VC has a more granular VLAN configuration than what is
+ * offered by the RTL8366x helper library. Extend this as you wish.
+ */
+ vlan4k_65mb.vid = vlan4k->vid;
+ vlan4k_65mb.member = vlan4k->member;
+ vlan4k_65mb.untag = vlan4k->untag;
+ vlan4k_65mb.fid = vlan4k->fid;
+
+ return _rtl8365mb_set_vlan_4k(smi, &vlan4k_65mb);
+}
+
+static int _rtl8365mb_get_vlan_mc(struct realtek_smi *smi, u32 index,
+ struct rtl8365mb_vlan_mc *vlanmc)
+{
+ u32 phys_member;
+ u16 data[4];
+ u32 val;
+ int ret;
+ int i;
+
+ if (index >= smi->num_vlan_mc)
+ return -EINVAL;
+
+ for (i = 0; i < 4; i++) {
+ ret = regmap_read(smi->map, RTL8365MB_VLAN_MC_REG(index) + i,
+ &val);
+ if (ret)
+ return ret;
+
+ data[i] = val & 0xFFFF;
+ }
+
+ memset(vlanmc, 0, sizeof(*vlanmc));
+
+ phys_member = FIELD_GET(RTL8365MB_VLAN_MC_D0_MBR_MASK, data[0]);
+ vlanmc->member = PORT_MASK_P2L(phys_member);
+ vlanmc->fid = FIELD_GET(RTL8365MB_VLAN_MC_D1_FID_MASK, data[1]);
+ vlanmc->meteridx =
+ FIELD_GET(RTL8365MB_VLAN_MC_D2_METERIDX_MASK, data[2]);
+ vlanmc->policing_en =
+ FIELD_GET(RTL8365MB_VLAN_MC_D2_ENVLANPOL_MASK, data[2]);
+ vlanmc->priority = FIELD_GET(RTL8365MB_VLAN_MC_D2_VBPRI_MASK, data[2]);
+ vlanmc->priority_en =
+ FIELD_GET(RTL8365MB_VLAN_MC_D2_VBPEN_MASK, data[2]);
+ vlanmc->evid = FIELD_GET(RTL8365MB_VLAN_MC_D3_EVID_MASK, data[3]);
+
+ return 0;
+}
+
+static int rtl8365mb_get_vlan_mc(struct realtek_smi *smi, u32 index,
+ struct rtl8366_vlan_mc *vlanmc)
+{
+ struct rtl8365mb_vlan_mc vlanmc_65mb;
+ struct rtl8365mb_vlan_4k vlan4k_65mb;
+ int ret;
+
+ ret = _rtl8365mb_get_vlan_mc(smi, index, &vlanmc_65mb);
+ if (ret)
+ return ret;
+
+ /* The untag field is not stored in the membership config, so grab it
+ * from the vlan4k table instead. This is mostly for compatibility with
+ * the RTL8366x helper library.
+ */
+ ret = _rtl8365mb_get_vlan_4k(smi, vlanmc_65mb.evid, &vlan4k_65mb);
+ if (ret)
+ return ret;
+
+ memset(vlanmc, 0, sizeof(*vlanmc));
+
+ vlanmc->vid = vlanmc_65mb.evid;
+ vlanmc->untag = vlan4k_65mb.untag;
+ vlanmc->member = vlanmc_65mb.member;
+ vlanmc->fid = vlanmc_65mb.fid;
+ vlanmc->priority = vlanmc_65mb.priority;
+
+ return 0;
+}
+
+static int _rtl8365mb_set_vlan_mc(struct realtek_smi *smi, u32 index,
+ const struct rtl8365mb_vlan_mc *vlanmc)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ u16 data[4] = { 0 };
+ u32 phys_member;
+ int ret;
+ int i;
+
+ if (index >= smi->num_vlan_mc || (vlanmc->member & ~(mb->port_mask)) ||
+ vlanmc->evid > RTL8365MB_EVIDMAX ||
+ vlanmc->fid > RTL8365MB_FIDMAX ||
+ vlanmc->priority > RTL8365MB_PRIORITYMAX ||
+ vlanmc->meteridx > RTL8365MB_METERMAX)
+ return -EINVAL;
+
+ phys_member = PORT_MASK_L2P(vlanmc->member);
+
+ data[0] |= FIELD_PREP(RTL8365MB_VLAN_MC_D0_MBR_MASK, phys_member);
+ data[1] |= FIELD_PREP(RTL8365MB_VLAN_MC_D1_FID_MASK, vlanmc->fid);
+ data[2] |= FIELD_PREP(RTL8365MB_VLAN_MC_D2_METERIDX_MASK,
+ vlanmc->meteridx);
+ data[2] |= FIELD_PREP(RTL8365MB_VLAN_MC_D2_ENVLANPOL_MASK,
+ vlanmc->policing_en);
+ data[2] |=
+ FIELD_PREP(RTL8365MB_VLAN_MC_D2_VBPRI_MASK, vlanmc->priority);
+ data[2] |= FIELD_PREP(RTL8365MB_VLAN_MC_D2_VBPEN_MASK,
+ vlanmc->priority_en);
+ data[3] |= FIELD_PREP(RTL8365MB_VLAN_MC_D3_EVID_MASK, vlanmc->evid);
+
+ for (i = 0; i < 4; i++) {
+ ret = regmap_write(smi->map, RTL8365MB_VLAN_MC_REG(index) + i,
+ data[i]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int rtl8365mb_set_vlan_mc(struct realtek_smi *smi, u32 index,
+ const struct rtl8366_vlan_mc *vlanmc)
+{
+ struct rtl8365mb_vlan_mc vlanmc_65mb = { 0 };
+
+ vlanmc_65mb.evid = vlanmc->vid;
+ /* The untag field is set in the corresponding vlan4k entry */
+ vlanmc_65mb.member = vlanmc->member;
+ vlanmc_65mb.fid = vlanmc->fid;
+ vlanmc_65mb.priority = vlanmc->priority;
+
+ return _rtl8365mb_set_vlan_mc(smi, index, &vlanmc_65mb);
+}
+
+static int rtl8365mb_get_mc_index(struct realtek_smi *smi, int port, int *index)
+{
+ int phys_port = PORT_NUM_L2P(port);
+ u32 val;
+ int ret;
+
+ if (port >= smi->num_ports || *index >= smi->num_vlan_mc)
+ return -EINVAL;
+
+ ret = regmap_read(smi->map, RTL8365MB_VLAN_PVID_CTRL_REG(phys_port),
+ &val);
+ if (ret)
+ return ret;
+
+ *index = (val & (RTL8365MB_VLAN_PVID_CTRL_PORT_VIDX_MASK(phys_port))) >>
+ RTL8365MB_VLAN_PVID_CTRL_PORT_VIDX_OFFSET(phys_port);
+
+ return 0;
+}
+
+static int rtl8365mb_set_mc_index(struct realtek_smi *smi, int port, int index)
+{
+ int phys_port = PORT_NUM_L2P(port);
+
+ if (port >= smi->num_ports || index >= smi->num_vlan_mc)
+ return -EINVAL;
+
+ return regmap_update_bits(
+ smi->map, RTL8365MB_VLAN_PVID_CTRL_REG(phys_port),
+ RTL8365MB_VLAN_PVID_CTRL_PORT_VIDX_MASK(phys_port),
+ index << RTL8365MB_VLAN_PVID_CTRL_PORT_VIDX_OFFSET(phys_port));
+}
+
+static int rtl8365mb_ports_isolate(struct realtek_smi *smi)
+{
+ u32 phys_mask = PORT_MASK_L2P(BIT(smi->cpu_port));
+ int ret;
+ int i;
+
+ /* Isolate all ports by setting the forwarding mask for each port to
+ * BIT(cpu_port). The switch will then forward all frames from the user
+ * ports to the CPU port only.
+ *
+ * For the CPU port, the forwarding mask is effectively zero. The switch
+ * will then reject all non-CPU tagged frames from the CPU port, and
+ * honour the TX mask in all CPU tagged frames from the CPU port
+ * irrespective of the forwarding mask.
+ */
+ for (i = 0; i < smi->num_ports; i++) {
+ u32 phys_port = PORT_NUM_L2P(i);
+
+ ret = regmap_write(smi->map,
+ RTL8365MB_PORT_ISOLATION_REG(phys_port),
+ phys_mask);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int rtl8365mb_get_mib_counter(struct realtek_smi *smi, int port,
+ struct rtl8366_mib_counter *mib,
+ u64 *mibvalue)
+{
+ int phys_port = PORT_NUM_L2P(port);
+ u32 offset;
+ u32 val;
+ int ret;
+ int i;
+
+ /* The MIB address is an SRAM address. We request a particular address
+ * and then poll the control register before reading the value from some
+ * counter registers.
+ */
+ ret = regmap_write(smi->map, RTL8365MB_MIB_ADDRESS_REG,
+ RTL8365MB_MIB_ADDRESS(phys_port, mib->offset));
+ if (ret)
+ return ret;
+
+ /* Poll for completion */
+ ret = regmap_read_poll_timeout(
+ smi->map, RTL8365MB_MIB_CTRL0_REG, val,
+ (val & RTL8365MB_MIB_CTRL0_BUSY_FLAG_MASK) == 0, 10, 100);
+ if (ret)
+ return ret;
+
+ /* Presumably this indicates a MIB counter read failure */
+ if (val & RTL8365MB_MIB_CTRL0_RESET_FLAG_MASK)
+ return -EIO;
+
+ /* There are four MIB counter registers each holding a 16 bit word of a
+ * MIB counter. Depending on the offset, we should read from the upper
+ * two or lower two registers. In case the MIB counter is 4 words, we
+ * read from all four registers.
+ */
+ if (mib->length == 4)
+ offset = 3;
+ else
+ offset = (mib->offset + 1) % 4;
+
+ /* Read the MIB counter 16 bits at a time */
+ *mibvalue = 0;
+ for (i = 0; i < mib->length; i++) {
+ ret = regmap_read(smi->map,
+ RTL8365MB_MIB_COUNTER_REG(offset - i), &val);
+ if (ret)
+ return ret;
+
+ *mibvalue = ((*mibvalue) << 16) | (val & 0xFFFF);
+ }
+
+ return 0;
+}
+
+static bool rtl8365mb_is_vlan_valid(struct realtek_smi *smi, unsigned int vlan)
+{
+ if (vlan > RTL8365MB_VIDMAX)
+ return false;
+
+ return true;
+}
+
+static int rtl8365mb_enable_vlan(struct realtek_smi *smi, bool enable)
+{
+ dev_dbg(smi->dev, "%s VLAN\n", enable ? "enable" : "disable");
+ return regmap_update_bits(
+ smi->map, RTL8365MB_VLAN_CTRL_REG, RTL8365MB_VLAN_CTRL_EN_MASK,
+ FIELD_PREP(RTL8365MB_VLAN_CTRL_EN_MASK, enable ? 1 : 0));
+}
+
+static int rtl8365mb_enable_vlan4k(struct realtek_smi *smi, bool enable)
+{
+ return rtl8365mb_enable_vlan(smi, enable);
+}
+
+static int rtl8365mb_get_and_clear_status_reg(struct realtek_smi *smi, u32 reg,
+ u32 *val)
+{
+ int ret;
+
+ ret = regmap_read(smi->map, reg, val);
+ if (ret)
+ return ret;
+
+ return regmap_write(smi->map, reg, *val);
+}
+
+static irqreturn_t rtl8365mb_irq(int irq, void *data)
+{
+ struct realtek_smi *smi = data;
+ struct rtl8365mb *mb;
+ u32 line_changes = 0;
+ u32 linkdown_ind;
+ u32 linkup_ind;
+ u32 stat;
+ u32 val;
+ int ret;
+
+ mb = smi->chip_data;
+
+ ret = rtl8365mb_get_and_clear_status_reg(smi, RTL8365MB_INTR_STATUS_REG,
+ &stat);
+ if (ret)
+ goto out_error;
+
+ if (stat & RTL8365MB_INTR_STATUS_LINK_CHANGE_MASK) {
+ ret = rtl8365mb_get_and_clear_status_reg(
+ smi, RTL8365MB_PORT_LINKUP_IND_REG, &val);
+ if (ret)
+ goto out_error;
+
+ linkup_ind = FIELD_GET(RTL8365MB_PORT_LINKUP_IND_MASK, val);
+
+ ret = rtl8365mb_get_and_clear_status_reg(
+ smi, RTL8365MB_PORT_LINKDOWN_IND_REG, &val);
+ if (ret)
+ goto out_error;
+
+ linkdown_ind = FIELD_GET(RTL8365MB_PORT_LINKDOWN_IND_MASK, val);
+
+ line_changes = PORT_MASK_P2L(linkup_ind | linkdown_ind) &
+ mb->phy_port_mask;
+ }
+
+ if (!line_changes)
+ goto out_none;
+
+ while (line_changes) {
+ int line = __ffs(line_changes);
+ int child_irq;
+
+ line_changes &= ~BIT(line);
+
+ child_irq = irq_find_mapping(smi->irqdomain, line);
+ handle_nested_irq(child_irq);
+ }
+
+ return IRQ_HANDLED;
+
+out_error:
+ dev_err(smi->dev, "failed to read interrupt status: %d\n", ret);
+
+out_none:
+ return IRQ_NONE;
+}
+
+static struct irq_chip rtl8365mb_irq_chip = {
+ .name = "rtl8365mb",
+ /* The hardware doesn't support masking IRQs on a per-port basis */
+};
+
+static int rtl8365mb_irq_map(struct irq_domain *domain, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_chip_data(irq, domain->host_data);
+ irq_set_chip_and_handler(irq, &rtl8365mb_irq_chip, handle_simple_irq);
+ irq_set_nested_thread(irq, 1);
+ irq_set_noprobe(irq);
+
+ return 0;
+}
+
+static void rtl8365mb_irq_unmap(struct irq_domain *d, unsigned int irq)
+{
+ irq_set_nested_thread(irq, 0);
+ irq_set_chip_and_handler(irq, NULL, NULL);
+ irq_set_chip_data(irq, NULL);
+}
+
+static const struct irq_domain_ops rtl8365mb_irqdomain_ops = {
+ .map = rtl8365mb_irq_map,
+ .unmap = rtl8365mb_irq_unmap,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+static int _rtl8365mb_irq_enable(struct realtek_smi *smi, bool enable)
+{
+ return regmap_update_bits(
+ smi->map, RTL8365MB_INTR_CTRL,
+ RTL8365MB_INTR_CTRL_LINK_CHANGE_MASK,
+ FIELD_PREP(RTL8365MB_INTR_CTRL_LINK_CHANGE_MASK,
+ enable ? 1 : 0));
+}
+
+static int rtl8365mb_irq_enable(struct realtek_smi *smi)
+{
+ return _rtl8365mb_irq_enable(smi, true);
+}
+
+static int rtl8365mb_irq_disable(struct realtek_smi *smi)
+{
+ return _rtl8365mb_irq_enable(smi, false);
+}
+
+static int rtl8365mb_irq_setup(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ struct device_node *intc;
+ u32 irq_trig;
+ int virq;
+ int irq;
+ u32 val;
+ int ret;
+ int i;
+
+ intc = of_get_child_by_name(smi->dev->of_node, "interrupt-controller");
+ if (!intc) {
+ dev_err(smi->dev, "missing child interrupt-controller node\n");
+ return -EINVAL;
+ }
+
+ smi->irqdomain = irq_domain_add_linear(intc, mb->num_phys,
+ &rtl8365mb_irqdomain_ops, smi);
+ if (!smi->irqdomain) {
+ dev_err(smi->dev, "failed to add irq domain\n");
+ ret = -ENOMEM;
+ goto out_put_node;
+ }
+
+ for (i = 0; i < mb->num_phys; i++) {
+ virq = irq_create_mapping(smi->irqdomain, i);
+ if (!virq) {
+ dev_err(smi->dev,
+ "failed to create irq domain mapping\n");
+ ret = -EINVAL;
+ goto out_remove_irqdomain;
+ }
+
+ irq_set_parent(virq, irq);
+ }
+
+ /* rtl8365mb IRQs cascade off this one */
+ irq = of_irq_get(intc, 0);
+ if (irq <= 0) {
+ if (irq != -EPROBE_DEFER)
+ dev_err(smi->dev, "failed to get parent irq: %d\n",
+ irq);
+ ret = irq ? irq : -EINVAL;
+ goto out_remove_irqdomain;
+ }
+
+ /* Configure chip interrupt signal polarity */
+ irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq));
+ switch (irq_trig) {
+ case IRQF_TRIGGER_RISING:
+ case IRQF_TRIGGER_HIGH:
+ val = RTL8365MB_INTR_POLARITY_HIGH;
+ break;
+ case IRQF_TRIGGER_FALLING:
+ case IRQF_TRIGGER_LOW:
+ val = RTL8365MB_INTR_POLARITY_LOW;
+ break;
+ default:
+ dev_err(smi->dev, "unsupported irq trigger type %u\n",
+ irq_trig);
+ ret = -EINVAL;
+ goto out_remove_irqdomain;
+ }
+
+ ret = regmap_update_bits(smi->map, RTL8365MB_INTR_POLARITY_REG,
+ RTL8365MB_INTR_POLARITY_MASK,
+ FIELD_PREP(RTL8365MB_INTR_POLARITY_MASK, val));
+ if (ret)
+ goto out_remove_irqdomain;
+
+ /* Disable the interrupt in case the chip has it enabled on reset */
+ ret = rtl8365mb_irq_disable(smi);
+ if (ret)
+ goto out_remove_irqdomain;
+
+ /* Clear the interrupt status register */
+ ret = regmap_write(smi->map, RTL8365MB_INTR_STATUS_REG,
+ RTL8365MB_INTR_STATUS_ALL_MASK);
+ if (ret)
+ goto out_remove_irqdomain;
+
+ ret = request_threaded_irq(irq, NULL, rtl8365mb_irq, IRQF_ONESHOT,
+ "rtl8365mb", smi);
+ if (ret) {
+ dev_err(smi->dev, "failed to request irq: %d\n", ret);
+ goto out_remove_irqdomain;
+ }
+
+ /* Store the irq so that we know to free it during teardown */
+ mb->irq = irq;
+
+ ret = rtl8365mb_irq_enable(smi);
+ if (ret)
+ goto out_free_irq;
+
+ of_node_put(intc);
+
+ return 0;
+
+out_free_irq:
+ free_irq(mb->irq, smi);
+ mb->irq = 0;
+
+out_remove_irqdomain:
+ for (i = 0; i < mb->num_phys; i++) {
+ virq = irq_find_mapping(smi->irqdomain, i);
+ irq_dispose_mapping(virq);
+ }
+
+ irq_domain_remove(smi->irqdomain);
+ smi->irqdomain = NULL;
+
+out_put_node:
+ of_node_put(intc);
+
+ return ret;
+}
+
+static void rtl8365mb_irq_teardown(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ int virq;
+ int i;
+
+ if (mb->irq) {
+ free_irq(mb->irq, smi);
+ mb->irq = 0;
+ }
+
+ if (smi->irqdomain) {
+ for (i = 0; i < mb->num_phys; i++) {
+ virq = irq_find_mapping(smi->irqdomain, i);
+ irq_dispose_mapping(virq);
+ }
+
+ irq_domain_remove(smi->irqdomain);
+ smi->irqdomain = NULL;
+ }
+}
+
+static int rtl8365mb_cpu_config(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ struct rtl8365mb_cpu *cpu = &mb->cpu;
+ u32 phys_mask;
+ u32 phys_trap_port;
+ u32 val;
+ int ret;
+
+ phys_mask = PORT_MASK_L2P(cpu->mask);
+ phys_trap_port = PORT_NUM_L2P(cpu->trap_port);
+
+ ret = regmap_update_bits(smi->map, RTL8365MB_CPU_PORT_MASK_REG,
+ RTL8365MB_CPU_PORT_MASK_MASK,
+ FIELD_PREP(RTL8365MB_CPU_PORT_MASK_MASK,
+ phys_mask));
+ if (ret)
+ return ret;
+
+ val = FIELD_PREP(RTL8365MB_CPU_CTRL_EN_MASK, cpu->enable ? 1 : 0) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_INSERTMODE_MASK, cpu->insert) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_POSITION_MASK, cpu->position) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK, cpu->rx_length) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK, cpu->format) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_MASK, phys_trap_port) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK,
+ phys_trap_port >> 3);
+ ret = regmap_write(smi->map, RTL8365MB_CPU_CTRL_REG, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_switch_init(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ int ret;
+ int i;
+
+ /* Do any chip-specific init jam before getting to the common stuff */
+ if (mb->jam_table) {
+ for (i = 0; i < mb->jam_size; i++) {
+ ret = regmap_write(smi->map, mb->jam_table[i].reg,
+ mb->jam_table[i].val);
+ if (ret)
+ return ret;
+ }
+ }
+
+ /* Common init jam */
+ for (i = 0; i < ARRAY_SIZE(rtl8365mb_init_jam_common); i++) {
+ ret = regmap_write(smi->map, rtl8365mb_init_jam_common[i].reg,
+ rtl8365mb_init_jam_common[i].val);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int rtl8365mb_reset_chip(struct realtek_smi *smi)
+{
+ u32 val;
+
+ realtek_smi_write_reg_noack(smi, RTL8365MB_CHIP_RESET_REG,
+ FIELD_PREP(RTL8365MB_CHIP_RESET_HW_MASK,
+ 1));
+
+ /* Realtek documentation says the chip needs 1 second to reset. Sleep
+ * for 100 ms before accessing any registers to prevent ACK timeouts.
+ */
+ msleep(100);
+ return regmap_read_poll_timeout(
+ smi->map, RTL8365MB_CHIP_RESET_REG, val,
+ (val & RTL8365MB_CHIP_RESET_HW_MASK) == 0, 20000, 1e6);
+}
+
+static int rtl8365mb_setup(struct dsa_switch *ds)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8365mb *mb;
+ int ret;
+
+ mb = smi->chip_data;
+
+ ret = rtl8365mb_reset_chip(smi);
+ if (ret) {
+ dev_err(smi->dev, "failed to reset chip: %d\n", ret);
+ return ret;
+ }
+
+ /* Configure switch to vendor-defined initial state */
+ ret = rtl8365mb_switch_init(smi);
+ if (ret) {
+ dev_err(smi->dev, "failed to initialize switch: %d\n", ret);
+ return ret;
+ }
+
+ /* Configure CPU tagging */
+ ret = rtl8365mb_cpu_config(smi);
+ if (ret)
+ return ret;
+
+ /* Isolate all ports per DSA setup requirements */
+ ret = rtl8365mb_ports_isolate(smi);
+ if (ret)
+ return ret;
+
+ /* Set maximum packet length to 1536 bytes */
+ ret = regmap_update_bits(smi->map, RTL8365MB_CFG0_MAX_LEN_REG,
+ RTL8365MB_CFG0_MAX_LEN_MASK,
+ FIELD_PREP(RTL8365MB_CFG0_MAX_LEN_MASK, 1536));
+ if (ret)
+ return ret;
+
+ /* Set up cascading IRQs */
+ ret = rtl8365mb_irq_setup(smi);
+ if (ret == -EPROBE_DEFER)
+ return ret;
+ else if (ret)
+ dev_info(smi->dev, "no interrupt support\n");
+
+ ret = realtek_smi_setup_mdio(smi);
+ if (ret) {
+ dev_err(smi->dev, "could not set up MDIO bus\n");
+ return -ENODEV;
+ }
+
+ return ret;
+}
+
+static void rtl8365mb_teardown(struct dsa_switch *ds)
+{
+ struct realtek_smi *smi = ds->priv;
+
+ realtek_smi_teardown_mdio(smi);
+ rtl8365mb_irq_teardown(smi);
+}
+
+static int rtl8365mb_get_chip_id_and_ver(struct regmap *map, u32 *id, u32 *ver)
+{
+ int ret;
+
+ /* For some reason we have to write a magic value to an arbitrary
+ * register whenever accessing the chip ID/version registers.
+ */
+ ret = regmap_write(map, RTL8365MB_MAGIC_REG, RTL8365MB_MAGIC_VALUE);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(map, RTL8365MB_CHIP_ID_REG, id);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(map, RTL8365MB_CHIP_VER_REG, ver);
+ if (ret)
+ return ret;
+
+ /* Reset magic register */
+ ret = regmap_write(map, RTL8365MB_MAGIC_REG, 0);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_detect(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ u32 chip_id;
+ u32 chip_ver;
+ int ret;
+
+ ret = rtl8365mb_get_chip_id_and_ver(smi->map, &chip_id, &chip_ver);
+ if (ret) {
+ dev_err(smi->dev, "failed to read chip id and version: %d\n",
+ ret);
+ return ret;
+ }
+
+ switch (chip_id) {
+ case RTL8365MB_CHIP_ID_8365MB_VC:
+ dev_info(smi->dev,
+ "found an RTL8365MB-VC switch (ver=0x%04x)\n",
+ chip_ver);
+
+ smi->cpu_port = RTL8365MB_CPU_PORT_NUM_8365MB_VC;
+ smi->num_ports = RTL8365MB_NUM_PORTS_8365MB_VC;
+ smi->num_vlan_mc = RTL8365MB_NUM_VLANS;
+ smi->mib_counters = rtl8365mb_mib_counters;
+ smi->num_mib_counters = ARRAY_SIZE(rtl8365mb_mib_counters);
+
+ mb->chip_id = chip_id;
+ mb->chip_ver = chip_ver;
+ mb->num_phys = RTL8365MB_NUM_PHYS_8365MB_VC;
+ mb->port_mask = RTL8365MB_PORT_MASK_8365MB_VC;
+ mb->phy_port_mask = RTL8365MB_PHY_PORT_MASK_8365MB_VC;
+ mb->jam_table = rtl8365mb_init_jam_8365mb_vc;
+ mb->jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc);
+
+ mb->cpu.enable = 1;
+ mb->cpu.mask = BIT(smi->cpu_port);
+ mb->cpu.trap_port = smi->cpu_port;
+ mb->cpu.insert = RTL8365MB_CPU_INSERT_TO_ALL;
+ mb->cpu.position = RTL8365MB_CPU_POS_AFTER_SA;
+ mb->cpu.rx_length = RTL8365MB_CPU_RXLEN_64BYTES;
+ mb->cpu.format = RTL8365MB_CPU_FORMAT_8BYTES;
+
+ break;
+ default:
+ dev_err(smi->dev,
+ "found an unknown Realtek switch (id=0x%04x, ver=0x%04x)\n",
+ chip_id, chip_ver);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static const struct dsa_switch_ops rtl8365mb_switch_ops = {
+ .get_tag_protocol = rtl8365mb_get_tag_protocol,
+ .setup = rtl8365mb_setup,
+ .teardown = rtl8365mb_teardown,
+ .phylink_validate = rtl8365mb_phylink_validate,
+ .phylink_mac_config = rtl8365mb_phylink_mac_config,
+ .phylink_mac_link_down = rtl8365mb_phylink_mac_link_down,
+ .phylink_mac_link_up = rtl8365mb_phylink_mac_link_up,
+ .get_strings = rtl8366_get_strings,
+ .get_ethtool_stats = rtl8366_get_ethtool_stats,
+ .get_sset_count = rtl8366_get_sset_count,
+ .port_vlan_filtering = rtl8365mb_port_vlan_filtering,
+ .port_vlan_add = rtl8366_vlan_add,
+ .port_vlan_del = rtl8366_vlan_del,
+ .port_enable = rtl8365mb_port_enable,
+ .port_disable = rtl8365mb_port_disable,
+};
+
+static const struct realtek_smi_ops rtl8365mb_smi_ops = {
+ .detect = rtl8365mb_detect,
+ .get_vlan_mc = rtl8365mb_get_vlan_mc,
+ .set_vlan_mc = rtl8365mb_set_vlan_mc,
+ .get_vlan_4k = rtl8365mb_get_vlan_4k,
+ .set_vlan_4k = rtl8365mb_set_vlan_4k,
+ .get_mc_index = rtl8365mb_get_mc_index,
+ .set_mc_index = rtl8365mb_set_mc_index,
+ .get_mib_counter = rtl8365mb_get_mib_counter,
+ .is_vlan_valid = rtl8365mb_is_vlan_valid,
+ .enable_vlan = rtl8365mb_enable_vlan,
+ .enable_vlan4k = rtl8365mb_enable_vlan4k,
+ .phy_read = rtl8365mb_phy_read,
+ .phy_write = rtl8365mb_phy_write,
+};
+
+const struct realtek_smi_variant rtl8365mb_variant = {
+ .ds_ops = &rtl8365mb_switch_ops,
+ .ops = &rtl8365mb_smi_ops,
+ .clk_delay = 10,
+ .cmd_read = 0xb9,
+ .cmd_write = 0xb8,
+ .chip_data_sz = sizeof(struct rtl8365mb),
+};
+EXPORT_SYMBOL_GPL(rtl8365mb_variant);
--
2.32.0
