On Fri, Aug 13, 2021 at 07:50:03PM -0700, Colin Foster wrote:
> Signed-off-by: Colin Foster <colin.foster@xxxxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/net/dsa/ocelot.txt | 92 +++++++++++++++++++
> 1 file changed, 92 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/net/dsa/ocelot.txt b/Documentation/devicetree/bindings/net/dsa/ocelot.txt
> index 7a271d070b72..edf560a50803 100644
> --- a/Documentation/devicetree/bindings/net/dsa/ocelot.txt
> +++ b/Documentation/devicetree/bindings/net/dsa/ocelot.txt
> @@ -8,6 +8,7 @@ Currently the switches supported by the felix driver are:
>
> - VSC9959 (Felix)
> - VSC9953 (Seville)
> +- VSC7511, VSC7512, VSC7513, VSC7514 via SPI
>
> The VSC9959 switch is found in the NXP LS1028A. It is a PCI device, part of the
> larger ENETC root complex. As a result, the ethernet-switch node is a sub-node
> @@ -211,3 +212,94 @@ Example:
> };
> };
> };
> +
> +The VSC7513 and VSC7514 switches can be controlled internally via the MIPS
> +processor. The VSC7511 and VSC7512 don't have this internal processor, but all
> +four chips can be controlled externally through SPI with the following required
> +properties:
> +
> +- compatible:
> + Can be "mscc,vsc7511", "mscc,vsc7512", "mscc,vsc7513", or
> + "mscc,vsc7514".
> +
> +Supported phy modes for all chips are:
> +
> +* phy_mode = "sgmii": on ports 0, 1, 2, 3
> +
> +The VSC7512 and 7514 also support:
> +
> +* phy_mode = "sgmii": on ports 4, 5, 6, 7
> +* phy_mode = "qsgmii": on ports 7, 8, 10
> +
> +Example for control from a BeagleBone Black
> +
> +&spi0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethernet-switch@0 {
> + compatible = "mscc,vsc7512";
> + spi-max-frequency = <250000>;
> + reg = <0>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + ethernet = <&mac>;
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <100>;
> + full-duplex;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + label = "swp1";
> + phy-handle = <&sw_phy1>;
> + phy-mode = "sgmii";
> + };
> +
> + port@2 {
> + reg = <2>;
> + label = "swp2";
> + phy-handle = <&sw_phy2>;
> + phy-mode = "sgmii";
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "swp3";
> + phy-handle = <&sw_phy3>;
> + phy-mode = "sgmii";
> + };
> + };
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + sw_phy1: ethernet-phy@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x1>;
> + };
> +
> + sw_phy2: ethernet-phy@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x2>;
> + };
> +
> + sw_phy3: ethernet-phy@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x3>;
> + };
> + };
> + };
> +};
If you want a whole new example, then convert this to DT schema. But is
there anything really new or different here to warrant another example?
Rob
