On 09/08/2021 15:10, Christian Hewitt wrote:
> Radxa Zero is a small form factor SBC based on the Amlogic S905Y2
> chipset that ships in a number of RAM/eMMC configurations:
>
> Boards with 512MB/1GB LPDDR4 RAM have no eMMC storage and BCM43436
> wireless (2.4GHz b/g/n) while 2GB/4GB boards have 8/16/32/64/128GB
> eMMC storage and BCM4345 wireless (2.4/5GHz a/b/g/n/ac).
>
> - Amlogic S905Y2 quad-core Cortex-A53
> - Mali G31-MP2 GPU
> - HDMI 2.1 output (micro)
> - 1x USB 2.0 port - Type C (OTG)
> - 1x USB 3.0 port - Type C (Host)
> - 1x micro SD Card slot
> - 40 Pin GPIO header
>
> Signed-off-by: Christian Hewitt <christianshewitt@xxxxxxxxx>
> ---
> arch/arm64/boot/dts/amlogic/Makefile | 1 +
> .../dts/amlogic/meson-g12a-radxa-zero.dts | 418 ++++++++++++++++++
> 2 files changed, 419 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12a-radxa-zero.dts
>
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index faa0a79a34f5..be308361e2f1 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -1,5 +1,6 @@
> # SPDX-License-Identifier: GPL-2.0
> dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-g12a-radxa-zero.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-radxa-zero.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-radxa-zero.dts
> new file mode 100644
> index 000000000000..d44d3881d9b9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-radxa-zero.dts
> @@ -0,0 +1,418 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2018 BayLibre SAS. All rights reserved.
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-g12a.dtsi"
> +#include <dt-bindings/gpio/meson-g12a-gpio.h>
> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
> +
> +/ {
> + compatible = "radxa,zero", "amlogic,g12a";
> + model = "Radxa Zero";
> +
> + aliases {
> + serial0 = &uart_AO;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x40000000>;
> + };
> +
> + cvbs-connector {
> + status = "disabled";
> + compatible = "composite-video-connector";
> +
> + port {
> + cvbs_connector_in: endpoint {
> + remote-endpoint = <&cvbs_vdac_out>;
> + };
> + };
> + };
> +
> + hdmi-connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_connector_in: endpoint {
> + remote-endpoint = <&hdmi_tx_tmds_out>;
> + };
> + };
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> + clocks = <&wifi32k>;
> + clock-names = "ext_clock";
> + };
> +
> + flash_1v8: regulator-flash_1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "FLASH_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_3v3>;
> + regulator-always-on;
> + };
Drop this one and directly use vcc_1v8 regulator
> +
> + dc_in: regulator-dc_in {
> + compatible = "regulator-fixed";
> + regulator-name = "DC_IN";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + }
The name is AO_5V on the Schematics
> +
> + vcc_1v8: regulator-vcc_1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_3v3>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3: regulator-vcc_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + vcc_5v: regulator-vcc_5v {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_5V";
The name is "HDMI_PW" on the Schematics
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&dc_in>;
> +
> + gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
> + enable-active-low;
As the Schematics, the HDMI 5v is always on, no need for a GPIO control here,
please replace with regulator-always-on;
> + };
> +
> + vddao_1v8: regulator-vddao_1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + vddao_3v3: regulator-vddao_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&dc_in>;
> + regulator-always-on;
> + };
> +
> + vddcpu: regulator-vddcpu {
> + compatible = "pwm-regulator";
> +
> + regulator-name = "VDDCPU";
> + regulator-min-microvolt = <721000>;
> + regulator-max-microvolt = <1022000>;
> +
> + vin-supply = <&dc_in>;
> +
> + pwms = <&pwm_AO_cd 1 1250 0>;
> + pwm-dutycycle-range = <100 0>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "amlogic,axg-sound-card";
> + model = "RADXA-ZERO";
> + audio-aux-devs = <&tdmout_b>;
> + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
> + "TDMOUT_B IN 1", "FRDDR_B OUT 1",
> + "TDMOUT_B IN 2", "FRDDR_C OUT 1",
> + "TDM_B Playback", "TDMOUT_B OUT";
> +
> + assigned-clocks = <&clkc CLKID_MPLL2>,
> + <&clkc CLKID_MPLL0>,
> + <&clkc CLKID_MPLL1>;
> + assigned-clock-parents = <0>, <0>, <0>;
> + assigned-clock-rates = <294912000>,
> + <270950400>,
> + <393216000>;
> + status = "okay";
> +
> + dai-link-0 {
> + sound-dai = <&frddr_a>;
> + };
> +
> + dai-link-1 {
> + sound-dai = <&frddr_b>;
> + };
> +
> + dai-link-2 {
> + sound-dai = <&frddr_c>;
> + };
> +
> + /* 8ch hdmi interface */
> + dai-link-3 {
> + sound-dai = <&tdmif_b>;
> + dai-format = "i2s";
> + dai-tdm-slot-tx-mask-0 = <1 1>;
> + dai-tdm-slot-tx-mask-1 = <1 1>;
> + dai-tdm-slot-tx-mask-2 = <1 1>;
> + dai-tdm-slot-tx-mask-3 = <1 1>;
> + mclk-fs = <256>;
> +
> + codec {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
> + };
> + };
> +
> + dai-link-4 {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
> +
> + codec {
> + sound-dai = <&hdmi_tx>;
> + };
> + };
> + };
> +
> + wifi32k: wifi32k {
> + compatible = "pwm-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> + };
> +};
> +
> +&arb {
> + status = "okay";
> +};
> +
> +&cec_AO {
> + pinctrl-0 = <&cec_ao_a_h_pins>;
> + pinctrl-names = "default";
> + status = "disabled";
> + hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&cecb_AO {
> + pinctrl-0 = <&cec_ao_b_h_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> + hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&clkc_audio {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vddcpu>;
> + operating-points-v2 = <&cpu_opp_table>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vddcpu>;
> + operating-points-v2 = <&cpu_opp_table>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vddcpu>;
> + operating-points-v2 = <&cpu_opp_table>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vddcpu>;
> + operating-points-v2 = <&cpu_opp_table>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cvbs_vdac_port {
> + cvbs_vdac_out: endpoint {
> + remote-endpoint = <&cvbs_connector_in>;
> + };
> +};
> +
> +&frddr_a {
> + status = "okay";
> +};
> +
> +&frddr_b {
> + status = "okay";
> +};
> +
> +&frddr_c {
> + status = "okay";
> +};
> +
> +&hdmi_tx {
> + status = "okay";
> + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
> + pinctrl-names = "default";
> + hdmi-supply = <&vcc_5v>;
> +};
> +
> +&hdmi_tx_tmds_port {
> + hdmi_tx_tmds_out: endpoint {
> + remote-endpoint = <&hdmi_connector_in>;
> + };
> +};
> +
> +&ir {
> + status = "disabled";
> + pinctrl-0 = <&remote_input_ao_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&pwm_AO_cd {
> + pinctrl-0 = <&pwm_ao_d_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin1";
> + status = "okay";
> +};
> +
> +&pwm_ef {
> + status = "okay";
> + pinctrl-0 = <&pwm_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin0";
> +};
> +
> +&saradc {
> + status = "okay";
> + vref-supply = <&vddao_1v8>;
> +};
> +
> +/* SDIO */
> +&sd_emmc_a {
> + status = "okay";
> + pinctrl-0 = <&sdio_pins>;
> + pinctrl-1 = <&sdio_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + sd-uhs-sdr50;
> + max-frequency = <100000000>;
> +
> + non-removable;
> + disable-wp;
> +
> + /* WiFi firmware requires power to be kept while in suspend */
> + keep-power-in-suspend;
> +
> + mmc-pwrseq = <&sdio_pwrseq>;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddao_1v8>;
> +
> + brcmf: wifi@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + interrupts = <&gpio GPIOX_7 GPIO_ACTIVE_HIGH>;
> + interrupt-names = "host-wake";
> + };
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> + status = "okay";
> + pinctrl-0 = <&sdcard_c_pins>;
> + pinctrl-1 = <&sdcard_clk_gate_c_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <100000000>;
> + disable-wp;
> +
> + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddao_3v3>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
> + pinctrl-1 = <&emmc_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + max-frequency = <200000000>;
> + disable-wp;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&flash_1v8>;
> +};
> +
> +&tdmif_b {
> + status = "okay";
> +};
> +
> +&tdmout_b {
> + status = "okay";
> +};
> +
> +&tohdmitx {
> + status = "okay";
> +};
> +
> +&uart_A {
> + status = "okay";
> + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> +
> + bluetooth {
> + compatible = "brcm,bcm43438-bt";
> + shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
> + max-speed = <2000000>;
> + clocks = <&wifi32k>;
> + clock-names = "lpo";
> + };
> +};
> +
> +&uart_AO {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_a_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&usb {
> + status = "okay";
> + dr_mode = "host";
> +};
>
Type-C controller is missing, something like was done on libretech-pc:
typec2_vbus: regulator-typec2_vbus {
typec2_vbus: regulator-typec2_vbus {
compatible = "regulator-fixed";
regulator-name = "TYPEC2_VBUS";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&vcc5v>;
gpio = <&gpio_ao GPIOAO_7 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
&ao_pinctrl {
/*
* Make sure the irq pin of the TYPE C controller is not driven
* by the SoC.
*/
fusb302_irq_pins: fusb302_irq {
mux {
groups = "GPIOAO_5";
function = "gpio_aobus";
bias-pull-up;
output-disable;
};
};
};
&i2c3 {
status = "okay";
pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
pinctrl-names = "default";
fusb302@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
pinctrl-0 = <&fusb302_irq_pins>;
pinctrl-names = "default";
interrupt-parent = <&gpio_intc>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
vbus-supply = <&typec2_vbus>;
status = "okay";
};
};
&usb2_phy0 {
phy-supply = <&typec2_vbus>;
};
&usb3_pcie_phy {
phy-supply = <&typec2_vbus>;
};
But, seems polarity swapping via GPIO is not implemented in drivers/usb/typec/tcpm/fusb302.c so no idea how to handle GPIOAO_6 for USB3 polarity control...
717 static int tcpm_set_polarity(struct tcpc_dev *dev,
718 enum typec_cc_polarity polarity)
719 {
720 return 0;
721 }
Repost with regulator changes, TypeC stuff is not mandatory for v1.
Thanks,
Neil
