Re: [PATCH v2 3/3] drm/panel: Add ilitek ili9341 panel driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Sam,

Thanks for your time on my code review.

On Thu, 22 Jul 2021 at 00:56, Sam Ravnborg <sam@xxxxxxxxxxxx> wrote:
>
> Hi Dillon,
>
> On Wed, Jul 21, 2021 at 03:41:28PM +0800, dillon.minfei@xxxxxxxxx wrote:
> > From: Dillon Min <dillon.minfei@xxxxxxxxx>
> >
> > This driver combine tiny/ili9341.c mipi_dbi_interface driver
> > with mipi_dpi_interface driver, can support ili9341 with serial
> > mode or parallel rgb interface mode by register configuration.
> >
> > Cc: Linus Walleij <linus.walleij@xxxxxxxxxx>
> > Signed-off-by: Dillon Min <dillon.minfei@xxxxxxxxx>
>
> I have not looked at the driver before, sorry for being late.
> A few nits in the following.

That's fine. thanks.

>
>         Sam
>
> > +#include <linux/bitops.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/module.h>
> > +#include <linux/of_device.h>
> > +#include <linux/regulator/consumer.h>
> > +#include <linux/spi/spi.h>
> > +#include <linux/delay.h>
> > +#include <video/mipi_display.h>
> > +#include <drm/drm_mipi_dbi.h>
> > +#include <drm/drm_gem_framebuffer_helper.h>
> > +#include <drm/drm_gem_cma_helper.h>
> > +#include <drm/drm_fb_helper.h>
> > +#include <drm/drm_atomic_helper.h>
> > +#include <drm/drm_gem_atomic_helper.h>
> > +
> > +#include <drm/drm_drv.h>
> > +#include <drm/drm_modes.h>
> > +#include <drm/drm_panel.h>
> > +#include <drm/drm_print.h>
>
> Spaces between blocks of includes.
> So linux/* goes in one block, video/* in next block, drm/* in the last
> block.
> Sort alphabetically in each block.

I will add this change to v3. thanks.

>
> > +
> > +/**
> > + * struct ili9341_config - the system specific ILI9341 configuration
> > + * @max_spi_speed: 10000000
> > + */
> Unless you plan to pull this into our kernel-doc there is really no need
> for a kernel-doc marker. On the other hand W=1 builds will tell if you
> missed something. So there are arguments both ways.

This driver was following the drm/panel/panel-ilitek-ili9322.c style,
I didn't realize the /** ... */ is the kernel-doc marker before. just because
W=1 report some warnings, so i add all this marker to struct ili9341_config

I will remove all the kernel-doc markers, and try to build with W=1
again, thanks.

>
> > +struct ili9341_config {
> > +     u32 max_spi_speed;
> > +     /** @mode: the drm display mode */
> > +     const struct drm_display_mode mode;
> > +     /** @ca: TODO: need comments for this register */
> > +     u8 ca[ILI9341_CA_LEN];
> > +     /** @power_b: TODO: need comments for this register */
> > +     u8 power_b[ILI9341_POWER_B_LEN];
> > +     /** @power_seq: TODO: need comments for this register */
> > +     u8 power_seq[ILI9341_POWER_SEQ_LEN];
> > +     /** @dtca: TODO: need comments for this register */
> > +     u8 dtca[ILI9341_DTCA_LEN];
> > +     /** @dtcb: TODO: need comments for this register */
> > +     u8 dtcb[ILI9341_DTCB_LEN];
> > +     /** @power_a: TODO: need comments for this register */
> > +     u8 power_a[ILI9341_POWER_A_LEN];
> > +     /** @frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */
> > +     u8 frc[ILI9341_FRC_LEN];
> > +     /** @prc: TODO: need comments for this register */
> > +     u8 prc;
> > +     /** @dfc_1: B6h DISCTRL (Display Function Control) */
> > +     u8 dfc_1[ILI9341_DFC_1_LEN];
> > +     /** @power_1: Power Control 1 (C0h) */
> > +     u8 power_1;
> > +     /** @power_2: Power Control 2 (C1h) */
> > +     u8 power_2;
> > +     /** @vcom_1: VCOM Control 1(C5h) */
> > +     u8 vcom_1[ILI9341_VCOM_1_LEN];
> > +     /** @vcom_2: VCOM Control 2(C7h) */
> > +     u8 vcom_2;
> > +     /** @address_mode: Memory Access Control (36h) */
> > +     u8 address_mode;
> > +     /** @g3amma_en: TODO: need comments for this register */
> > +     u8 g3amma_en;
> > +     /** @rgb_interface: RGB Interface Signal Control (B0h) */
> > +     u8 rgb_interface;
> > +     /** @dfc_2: refer to dfc_1 */
> > +     u8 dfc_2[ILI9341_DFC_2_LEN];
> > +     /** @column_addr: Column Address Set (2Ah) */
> > +     u8 column_addr[ILI9341_COLUMN_ADDR_LEN];
> > +     /** @page_addr: Page Address Set (2Bh) */
> > +     u8 page_addr[ILI9341_PAGE_ADDR_LEN];
> > +     /** @interface: Interface Control (F6h) */
> > +     u8 interface[ILI9341_INTERFACE_LEN];
> > +     /** @pixel_format: This command sets the pixel format for the RGB */
> > +     /* image data used by
> > +      */
> > +     u8 pixel_format;
> > +     /** @gamma_curve: This command is used to select the desired Gamma */
> > +     /* curve for the
> > +      */
> Make this a single comment block.

Okay.

>
> > +     u8 gamma_curve;
> > +     /** @pgamma: Positive Gamma Correction (E0h) */
> > +     u8 pgamma[ILI9341_PGAMMA_LEN];
> > +     /** @ngamma: Negative Gamma Correction (E1h) */
> > +     u8 ngamma[ILI9341_NGAMMA_LEN];
> > +};
> > +
> > +struct ili9341 {
> > +     struct device *dev;
> We will have struct device * both in drm_panel and in ili9341.
> You could brop the one in ili9341.

Okay, I will use the dev from 'struct drm_panel'.

>
> > +     const struct ili9341_config *conf;
> > +     struct drm_panel panel;
> > +     struct gpio_desc *reset_gpio;
> > +     struct gpio_desc *dc_gpio;
> > +     struct mipi_dbi *dbi;
> > +     u32 max_spi_speed;
> > +     struct regulator_bulk_data supplies[3];
> > +};
> > +
> > +/*
> > + * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller
> > + */
> > +static const struct ili9341_config ili9341_stm32f429_disco_data = {
> > +     .max_spi_speed = 10000000,
> > +     .mode = {
> > +             .clock = 6100,
> > +             .hdisplay = 240,
> > +             .hsync_start = 240 + 10,/* hfp 10 */
> > +             .hsync_end = 240 + 10 + 10,/* hsync 10 */
> > +             .htotal = 240 + 10 + 10 + 20,/* hbp 20 */
> > +             .vdisplay = 320,
> > +             .vsync_start = 320 + 4,/* vfp 4 */
> > +             .vsync_end = 320 + 4 + 2,/* vsync 2 */
> > +             .vtotal = 320 + 4 + 2 + 2,/* vbp 2 */
> > +             .flags = 0,
> > +             .width_mm = 65,
> > +             .height_mm = 50,
> > +             .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
> > +     },
> > +     .ca = {0xc3, 0x08, 0x50},
> > +     .power_b = {0x00, 0xc1, 0x30},
> > +     .power_seq = {0x64, 0x03, 0x12, 0x81},
> > +     .dtca = {0x85, 0x00, 0x78},
> > +     .power_a = {0x39, 0x2c, 0x00, 0x34, 0x02},
> > +     .prc = 0x20,
> > +     .dtcb = {0x00, 0x00},
> > +     /* 0x00 fosc, 0x1b 70hz */
> > +     .frc = {0x00, 0x1b},
> > +     /* 0x0a Interval scan, AGND AGND AGND AGND
> > +      * 0xa2 Normally white, G1 -> G320, S720 -> S1,
> > +      *      Scan Cycle 5 frames,85ms
> > +      */
> > +     .dfc_1 = {0x0a, 0xa2},
> > +     /* 0x10 3.65v */
> > +     .power_1 = 0x10,
> > +     /* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */
> > +     .power_2 = 0x10,
> > +     /* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/
> > +     .vcom_1 = {0x45, 0x15},
> > +     /* 0x90 offset voltage, VMH-48, VML-48 */
> > +     .vcom_2 = 0x90,
> > +     /* 0xc8 Row Address Order, Column Address Order
> > +      * BGR 1
> > +      */
> > +     .address_mode = 0xc8,
> > +     .g3amma_en = 0x00,
> > +     /* 0xc2
> > +      * Display Data Path: Memory
> > +      * RGB: DE mode
> > +      * DOTCLK polarity set (data fetched at the falling time)
> > +      */
> > +     .rgb_interface = ILI9341_RGB_DISP_PATH_MEM |
> > +                     ILI9341_RGB_DE_MODE |
> > +                     ILI9341_RGB_DPL,
> > +     /*
> > +      * 0x0a
> > +      * Gate outputs in non-display area: Interval scan
> > +      * Determine source/VCOM output in a non-display area in the partial
> > +      * display mode: AGND AGND AGND AGND
> > +      *
> > +      * 0xa7
> > +      * Scan Cycle: 15 frames
> > +      * fFLM = 60Hz: 255ms
> > +      * Liquid crystal type: Normally white
> > +      * Gate Output Scan Direction: G1 -> G320
> > +      * Source Output Scan Direction: S720 -> S1
> > +      *
> > +      * 0x27
> > +      * LCD Driver Line: 320 lines
> > +      *
> > +      * 0x04
> > +      * PCDIV: 4
> > +      */
> > +     .dfc_2 = {0x0a, 0xa7, 0x27, 0x04},
> > +     /* column address: 240 */
> > +     .column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff,
> > +                             ILI9341_COLUMN_ADDR & 0xff},
> > +     /* page address: 320 */
> > +     .page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff,
> > +                             ILI9341_PAGE_ADDR & 0xff},
> > +     /* Memory write control: When the transfer number of data exceeds
> > +      * (EC-SC+1)*(EP-SP+1), the column and page number will be
> > +      * reset, and the exceeding data will be written into the following
> > +      * column and page.
> > +      * Display Operation Mode: RGB Interface Mode
> > +      * Interface for RAM Access: RGB interface
> > +      * 16- bit RGB interface (1 transfer/pixel)
> > +      */
> > +     .interface = {ILI9341_IF_WE_MODE, 0x00,
> > +                     ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB},
> > +     /* DPI: 16 bits / pixel */
> > +     .pixel_format = ILI9341_PIXEL_DPI_16_BITS,
> > +     /* Curve Selected: Gamma curve 1 (G2.2) */
> > +     .gamma_curve = ILI9341_GAMMA_CURVE_1,
> > +     .pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e,
> > +                     0x09, 0x4e, 0x78, 0x3c, 0x09,
> > +                     0x13, 0x05, 0x17, 0x11, 0x00},
> > +     .ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11,
> > +                     0x07, 0x31, 0x33, 0x42, 0x05,
> > +                     0x0c, 0x0a, 0x28, 0x2f, 0x0f},
> > +};
> > +
> > +static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel)
> > +{
> > +     return container_of(panel, struct ili9341, panel);
> > +}
> > +
> > +static void ili9341_dpi_init(struct ili9341 *ili)
> > +{
> > +     struct mipi_dbi *dbi = ili->dbi;
> > +     struct ili9341_config *cfg = (struct ili9341_config *)ili->conf;
> > +
> > +     /* Power Control */
> > +     mipi_dbi_command_stackbuf(dbi, 0xca, cfg->ca, ILI9341_CA_LEN);
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_POWERB, cfg->power_b,
> > +                               ILI9341_POWER_B_LEN);
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_POWER_SEQ, cfg->power_seq,
> > +                               ILI9341_POWER_SEQ_LEN);
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_DTCA, cfg->dtca,
> > +                               ILI9341_DTCA_LEN);
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_POWERA, cfg->power_a,
> > +                               ILI9341_POWER_A_LEN);
> > +     mipi_dbi_command(ili->dbi, ILI9341_PRC, cfg->prc);
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_DTCB, cfg->dtcb,
> > +                               ILI9341_DTCB_LEN);
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_FRC, cfg->frc, ILI9341_FRC_LEN);
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_1,
> > +                               ILI9341_DFC_1_LEN);
> > +     mipi_dbi_command(dbi, ILI9341_POWER1, cfg->power_1);
> > +     mipi_dbi_command(dbi, ILI9341_POWER2, cfg->power_2);
> > +
> > +     /* VCOM */
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_VCOM1, cfg->vcom_1,
> > +                               ILI9341_VCOM_1_LEN);
> > +     mipi_dbi_command(dbi, ILI9341_VCOM2, cfg->vcom_2);
> > +     mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, cfg->address_mode);
> > +
> > +     /* Gamma */
> > +     mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, cfg->g3amma_en);
> > +     mipi_dbi_command(dbi, ILI9341_RGB_INTERFACE, cfg->rgb_interface);
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_2,
> > +                               ILI9341_DFC_2_LEN);
> > +
> > +     /* Colomn address set */
> > +     mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_COLUMN_ADDRESS,
> > +                               cfg->column_addr, ILI9341_COLUMN_ADDR_LEN);
> > +
> > +     /* Page address set */
> > +     mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_PAGE_ADDRESS,
> > +                               cfg->page_addr, ILI9341_PAGE_ADDR_LEN);
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_INTERFACE, cfg->interface,
> > +                               ILI9341_INTERFACE_LEN);
> > +
> > +     /* Format */
> > +     mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, cfg->pixel_format);
> > +     mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START);
> > +     msleep(200);
> > +     mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, cfg->gamma_curve);
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_PGAMMA, cfg->pgamma,
> > +                               ILI9341_PGAMMA_LEN);
> > +     mipi_dbi_command_stackbuf(dbi, ILI9341_NGAMMA, cfg->ngamma,
> > +                               ILI9341_NGAMMA_LEN);
> > +     mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
> > +     msleep(200);
> > +     mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
> > +     mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START);
> > +
> > +     dev_info(ili->dev, "initialized display rgb interface\n");
> > +}
> > +
> > +static int ili9341_dpi_power_on(struct ili9341 *ili)
> > +{
> > +     int ret = 0;
> > +
> > +     /* Assert RESET */
> > +     gpiod_set_value(ili->reset_gpio, 1);
> > +
> > +     /* Enable power */
> > +     ret = regulator_bulk_enable(ARRAY_SIZE(ili->supplies),
> > +                                 ili->supplies);
> > +     if (ret < 0) {
> > +             dev_err(ili->dev, "unable to enable vcc\n");
> > +             return ret;
> > +     }
> > +     msleep(20);
> > +
> > +     /* De-assert RESET */
> > +     gpiod_set_value(ili->reset_gpio, 0);
> > +     msleep(20);
> > +
> > +     return 0;
> > +}
> > +
> > +static int ili9341_dpi_power_off(struct ili9341 *ili)
> > +{
> > +     /* Assert RESET */
> > +     gpiod_set_value(ili->reset_gpio, 1);
> > +
> > +     /* Disable power */
> > +     return regulator_bulk_disable(ARRAY_SIZE(ili->supplies),
> > +                                   ili->supplies);
> > +}
> > +
> > +static int ili9341_dpi_disable(struct drm_panel *panel)
> > +{
> > +     struct ili9341 *ili = panel_to_ili9341(panel);
> > +
> > +     mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_OFF);
> > +     return 0;
> > +}
> > +
> > +static int ili9341_dpi_unprepare(struct drm_panel *panel)
> > +{
> > +     struct ili9341 *ili = panel_to_ili9341(panel);
> > +
> > +     return ili9341_dpi_power_off(ili);
> > +}
> > +
> > +static int ili9341_dpi_prepare(struct drm_panel *panel)
> > +{
> > +     struct ili9341 *ili = panel_to_ili9341(panel);
> > +     int ret;
> > +
> > +     ret = ili9341_dpi_power_on(ili);
> > +     if (ret < 0)
> > +             return ret;
> > +
> > +     ili9341_dpi_init(ili);
> > +
> > +     return ret;
> > +}
> > +
> > +static int ili9341_dpi_enable(struct drm_panel *panel)
> > +{
> > +     struct ili9341 *ili = panel_to_ili9341(panel);
> > +
> > +     mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_ON);
> > +     return 0;
> > +}
> > +
> > +static int ili9341_dpi_get_modes(struct drm_panel *panel,
> > +                              struct drm_connector *connector)
> > +{
> > +     struct ili9341 *ili = panel_to_ili9341(panel);
> > +     struct drm_device *drm = connector->dev;
> > +     struct drm_display_mode *mode;
> > +     struct drm_display_info *info;
> > +
> > +     info = &connector->display_info;
> > +     info->width_mm = ili->conf->mode.width_mm;
> > +     info->height_mm = ili->conf->mode.height_mm;
> > +
> > +     if (ili->conf->rgb_interface & ILI9341_RGB_DPL)
> > +             info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE;
> > +     else
> > +             info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE;
> > +
> > +     if (ili->conf->rgb_interface & ILI9341_RGB_EPL)
> > +             info->bus_flags |= DRM_BUS_FLAG_DE_LOW;
> > +     else
> > +             info->bus_flags |= DRM_BUS_FLAG_DE_HIGH;
> > +
> > +     mode = drm_mode_duplicate(drm, &ili->conf->mode);
> > +     if (!mode) {
> > +             DRM_ERROR("bad mode or failed to add mode\n");
>
> DRM_ERROR and friends are not used in panel/* - the new variants
> drm_err() shall be used.
> This goes for the other uses of DRM_* as well.

Okay, I will change to using drm_err().

>
> > +             return -EINVAL;
> > +     }
> > +     drm_mode_set_name(mode);
> > +
> > +     /* Set up the polarity */
> > +     if (ili->conf->rgb_interface & ILI9341_RGB_HSPL)
> > +             mode->flags |= DRM_MODE_FLAG_PHSYNC;
> > +     else
> > +             mode->flags |= DRM_MODE_FLAG_NHSYNC;
> > +
> > +     if (ili->conf->rgb_interface & ILI9341_RGB_VSPL)
> > +             mode->flags |= DRM_MODE_FLAG_PVSYNC;
> > +     else
> > +             mode->flags |= DRM_MODE_FLAG_NVSYNC;
> > +
> > +     drm_mode_probed_add(connector, mode);
> > +
> > +     return 1; /* Number of modes */
> > +}
> > +
> > +static const struct drm_panel_funcs ili9341_dpi_funcs = {
> > +     .disable = ili9341_dpi_disable,
> > +     .unprepare = ili9341_dpi_unprepare,
> > +     .prepare = ili9341_dpi_prepare,
> > +     .enable = ili9341_dpi_enable,
> > +     .get_modes = ili9341_dpi_get_modes,
> > +};
> > +
> > +static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe,
> > +                            struct drm_crtc_state *crtc_state,
> > +                            struct drm_plane_state *plane_state)
> > +{
> > +     struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev);
> > +     struct mipi_dbi *dbi = &dbidev->dbi;
> > +     u8 addr_mode;
> > +     int ret, idx;
> > +
> > +     if (!drm_dev_enter(pipe->crtc.dev, &idx))
> > +             return;
> > +
> > +     DRM_DEBUG_KMS("\n");
> > +
> > +     ret = mipi_dbi_poweron_conditional_reset(dbidev);
> > +     if (ret < 0)
> > +             goto out_exit;
> > +     if (ret == 1)
> > +             goto out_enable;
> > +
> > +     mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF);
> > +
> > +     mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30);
> > +     mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81);
> > +     mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78);
> > +     mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02);
> > +     mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL);
> > +     mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00);
> > +
> > +     /* Power Control */
> > +     mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V);
> > +     mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT);
> > +     /* VCOM */
> > +     mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V,
> > +                      ILI9341_DBI_VCOM_1_VML_1P5V);
> > +     mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58);
> > +
> > +     /* Memory Access Control */
> > +     mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT,
> > +                      MIPI_DCS_PIXEL_FMT_16BIT);
> > +
> > +     /* Frame Rate */
> > +     mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03,
> > +                      ILI9341_DBI_FRC_RTNA & 0x1f);
> > +
> > +     /* Gamma */
> > +     mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00);
> > +     mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1);
> > +     mipi_dbi_command(dbi, ILI9341_PGAMMA,
> > +                      0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1,
> > +                      0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00);
> > +     mipi_dbi_command(dbi, ILI9341_NGAMMA,
> > +                      0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1,
> > +                      0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f);
> > +
> > +     /* DDRAM */
> > +     mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS |
> > +                      ILI9341_DBI_EMS_DTS |
> > +                      ILI9341_DBI_EMS_GON);
> > +
> > +     /* Display */
> > +     mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00);
> > +     mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
> > +     msleep(100);
> > +
> > +     mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
> > +     msleep(100);
> > +
> > +out_enable:
> > +     switch (dbidev->rotation) {
> > +     default:
> > +             addr_mode = ILI9341_MADCTL_MX;
> > +             break;
> > +     case 90:
> > +             addr_mode = ILI9341_MADCTL_MV;
> > +             break;
> > +     case 180:
> > +             addr_mode = ILI9341_MADCTL_MY;
> > +             break;
> > +     case 270:
> > +             addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY |
> > +                         ILI9341_MADCTL_MX;
> > +             break;
> > +     }
> > +     addr_mode |= ILI9341_MADCTL_BGR;
> > +     mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode);
> > +     mipi_dbi_enable_flush(dbidev, crtc_state, plane_state);
> > +     DRM_DEBUG_KMS("initialized display serial interface\n");
> > +out_exit:
> > +     drm_dev_exit(idx);
> > +}
> > +
> > +static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = {
> > +     .enable = ili9341_dbi_enable,
> > +     .disable = mipi_dbi_pipe_disable,
> > +     .update = mipi_dbi_pipe_update,
> > +     .prepare_fb = drm_gem_simple_display_pipe_prepare_fb,
> > +};
>
> So this is a full display driver. The more relevant home for this driver
> is inside drm/tiny/.

Yes, actually, this is the major topic I'd like to discuss with
maintainers here.
There are some options to support this panel.

- support only-dbi interface by drm/tiny/ili9341.c
- support dbi(register) + dpi(data) by drm/panel/panel-ilitek-ili9341.c
  (remove the code copied from tiny/ili9341.c)
- move all the code which support dbi+dpi to drm/tiny/ili9341.c
  (remove this driver)
- keep this driver, remove tiny/ili9341.c

I don't have a preferred one for this, all fine with me.
After I get the decision from you and other maintainers,
I will change the code.

It's meanful for other panels which have the same situations.

>
> > +
> > +static const struct drm_display_mode ili9341_dbi_mode = {
> > +     DRM_SIMPLE_MODE(240, 320, 37, 49),
> > +};
> > +
> > +DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops);
> > +
> > +static struct drm_driver ili9341_dbi_driver = {
> > +     .driver_features        = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC,
> > +     .fops                   = &ili9341_dbi_fops,
> > +     DRM_GEM_CMA_DRIVER_OPS_VMAP,
> > +     .debugfs_init           = mipi_dbi_debugfs_init,
> > +     .name                   = "ili9341",
> > +     .desc                   = "Ilitek ILI9341",
> > +     .date                   = "20210716",
> > +     .major                  = 1,
> > +     .minor                  = 0,
> > +};
> > +
> > +static int _ili9341_probe(struct spi_device *spi, bool dpi)
> > +{
> > +     struct gpio_desc *dc;
> > +     struct gpio_desc *reset;
> > +     struct device *dev = &spi->dev;
> > +     int ret;
> > +
> > +     reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
> > +     if (IS_ERR(reset))
> > +             DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n");
> > +
> > +     dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW);
> > +     if (IS_ERR(dc))
> > +             DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n");
> > +
> > +     if (!dpi) {
> > +             struct mipi_dbi_dev *dbidev;
> > +             struct mipi_dbi *dbi;
> > +             struct drm_device *drm;
> > +             struct regulator *vcc;
> > +             u32 rotation = 0;
> > +
> > +             vcc = devm_regulator_get_optional(dev, "vcc");
> > +             if (IS_ERR(vcc))
> > +                     DRM_DEV_ERROR(dev, "get optional vcc failed\n");
> > +
> > +             dbidev = devm_drm_dev_alloc(dev, &ili9341_dbi_driver,
> > +                                         struct mipi_dbi_dev, drm);
> > +             if (IS_ERR(dbidev))
> > +                     return PTR_ERR(dbidev);
> > +
> > +             dbi = &dbidev->dbi;
> > +             drm = &dbidev->drm;
> > +             dbi->reset = reset;
> > +             dbidev->regulator = vcc;
> > +
> > +             drm_mode_config_init(drm);
> > +             dbidev->backlight = devm_of_find_backlight(dev);
> > +             if (IS_ERR(dbidev->backlight))
> > +                     return PTR_ERR(dbidev->backlight);
> > +
> > +             device_property_read_u32(dev, "rotation", &rotation);
> > +
> > +             ret = mipi_dbi_spi_init(spi, dbi, dc);
> > +             if (ret)
> > +                     return ret;
> > +
> > +             ret = mipi_dbi_dev_init(dbidev, &ili9341_dbi_funcs,
> > +                                     &ili9341_dbi_mode, rotation);
> > +             if (ret)
> > +                     return ret;
> > +
> > +             drm_mode_config_reset(drm);
> > +
> > +             ret = drm_dev_register(drm, 0);
> > +             if (ret)
> > +                     return ret;
> > +
> > +             spi_set_drvdata(spi, drm);
> > +
> > +             drm_fbdev_generic_setup(drm, 0);
> > +     } else {
> > +             struct ili9341 *ili;
> > +
> > +             ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL);
> > +             if (!ili)
> > +                     return -ENOMEM;
> > +
> > +             ili->dbi = devm_kzalloc(dev, sizeof(struct mipi_dbi),
> > +                                     GFP_KERNEL);
> > +             if (!ili->dbi)
> > +                     return -ENOMEM;
> > +
> > +             ili->supplies[0].supply = "vci";
> > +             ili->supplies[1].supply = "vddi";
> > +             ili->supplies[2].supply = "vddi-led";
> > +
> > +             ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ili->supplies),
> > +                                           ili->supplies);
> > +             if (ret < 0) {
> > +                     dev_err(dev, "failed to get regulators: %d\n", ret);
> > +                     return ret;
> > +             }
> > +
> > +             ret = mipi_dbi_spi_init(spi, ili->dbi, dc);
> > +             if (ret)
> > +                     return ret;
> > +
> > +             spi_set_drvdata(spi, ili);
> > +
> > +             ili->dev = dev;
> > +             ili->reset_gpio = reset;
> > +             /*
> > +              * Every new incarnation of this display must have a unique
> > +              * data entry for the system in this driver.
> > +              */
> > +             ili->conf = of_device_get_match_data(dev);
> > +             if (!ili->conf) {
> > +                     dev_err(dev, "missing device configuration\n");
> > +                     return -ENODEV;
> > +             }
> > +
> > +             ili->max_spi_speed = ili->conf->max_spi_speed;
> > +
> > +             drm_panel_init(&ili->panel, dev, &ili9341_dpi_funcs,
> > +                            DRM_MODE_CONNECTOR_DPI);
> > +
> > +             drm_panel_add(&ili->panel);
> > +     }
> > +
> > +     return 0;
> > +}
> > +
> > +static int ili9341_probe(struct spi_device *spi)
> > +{
> > +     const struct spi_device_id *id = spi_get_device_id(spi);
> > +
> > +     if (!strcmp(id->name, "sf-tc240t-9370-t"))
> > +             return _ili9341_probe(spi, true);
> > +     else if (!strcmp(id->name, "yx240qv29"))
> > +             return _ili9341_probe(spi, false);
> > +
> > +     return -1;
> > +}
> > +
> > +static int ili9341_remove(struct spi_device *spi)
> > +{
> > +     const struct spi_device_id *id = spi_get_device_id(spi);
> > +     struct ili9341 *ili = spi_get_drvdata(spi);
> > +     struct drm_device *drm = spi_get_drvdata(spi);
> > +
> > +     if (!strcmp(id->name, "sf-tc240t-9370-t")) {
> > +             ili9341_dpi_power_off(ili);
> > +             drm_panel_remove(&ili->panel);
> > +     } else if (!strcmp(id->name, "yx240qv29")) {
> > +             drm_dev_unplug(drm);
> > +             drm_atomic_helper_shutdown(drm);
> > +     }
> > +     return 0;
> > +}
> > +
> > +static void ili9341_shutdown(struct spi_device *spi)
> > +{
> > +     const struct spi_device_id *id = spi_get_device_id(spi);
> > +
> > +     if (!strcmp(id->name, "yx240qv29"))
> > +             drm_atomic_helper_shutdown(spi_get_drvdata(spi));
> > +}
> > +
> > +static const struct of_device_id ili9341_of_match[] = {
> > +     {
> > +             .compatible = "st,sf-tc240t-9370-t",
> > +             .data = &ili9341_stm32f429_disco_data,
> > +     },
> > +     {
> > +             /* porting from tiny/ili9341.c
> > +              * for original mipi dbi compitable
> > +              */
> > +             .compatible = "adafruit,yx240qv29",
> > +             .data = NULL,
> > +     },
> > +};
> > +MODULE_DEVICE_TABLE(of, ili9341_of_match);
> > +
> > +static const struct spi_device_id ili9341_id[] = {
> > +     { "yx240qv29", 0 },
> > +     { "sf-tc240t-9370-t", 0 },
> > +     { }
> > +};
> > +MODULE_DEVICE_TABLE(spi, ili9341_id);
> > +
> > +static struct spi_driver ili9341_driver = {
> > +     .probe = ili9341_probe,
> > +     .remove = ili9341_remove,
> > +     .shutdown = ili9341_shutdown,
> > +     .id_table = ili9341_id,
> > +     .driver = {
> > +             .name = "panel-ilitek-ili9341",
> > +             .of_match_table = ili9341_of_match,
> > +     },
> > +};
> > +module_spi_driver(ili9341_driver);
> > +
> > +MODULE_AUTHOR("Dillon Min <dillon.minfei@xxxxxxxxx>");
> > +MODULE_DESCRIPTION("ILI9341 LCD panel driver");
> > +MODULE_LICENSE("GPL v2");
> > --
> > 2.7.4



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux