Re: [PATCH V3] arm64: dts: qcom: sc7280: Add nodes for eMMC and SD card

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2021-06-10 02:15, Konrad Dybcio wrote:
Hi,


diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 3900cfc..8b159d1 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -11,6 +11,7 @@
 #include <dt-bindings/iio/qcom,spmi-adc7-pmr735b.h>
 #include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
 #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
+#include <dt-bindings/gpio/gpio.h>
 #include "sc7280.dtsi"
 #include "pm7325.dtsi"
 #include "pmr735a.dtsi"
@@ -272,6 +273,36 @@
 	status = "okay";
 };

+&sdhc_1 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_clk &sdc1_cmd &sdc1_data &sdc1_rclk>;
+ pinctrl-1 = <&sdc1_clk_sleep &sdc1_cmd_sleep &sdc1_data_sleep &sdc1_rclk_sleep>;

Please condense these pins into a since sdc1_on_state/sdc1_off_state
(check sdc1_state_on in [1])

Sure


+
+	non-removable;
+	no-sd;
+	no-sdio;
+
+	vmmc-supply = <&vreg_l7b_2p9>;
+	vqmmc-supply = <&vreg_l19b_1p8>;
+
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_cd>;
+	pinctrl-1 = <&sdc2_clk_sleep &sdc2_cmd_sleep &sdc2_data_sleep>;

Ditto

Sure


+&tlmm {
+	sdc1_clk: sdc1-clk {
+		pins = "sdc1_clk";
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	sdc1_cmd: sdc1-cmd {
+		pins = "sdc1_cmd";
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	sdc1_data: sdc1-data {
+		pins = "sdc1_data";
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+	sdc1_rclk: sdc1-rclk {
+		pins = "sdc1_rclk";
+		bias-pull-down;
+	};
+
+	sdc2_clk: sdc2-clk {
+		pins = "sdc2_clk";
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	sdc2_cmd: sdc2-cmd {
+		pins = "sdc2_cmd";
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	sdc2_data: sdc2-data {
+		pins = "sdc2_data";
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	sd_cd: sd-cd {

Please make it sdc2 to keep things coherent.

Sure


+		pins = "gpio91";
+		bias-pull-up;
+	};
+
+};

Why are you defining on_state pins in the device dt and sleep state in
the SoC one?

Most devices share a common config for these, often coming from MTP or
QRD boards

and it makes little to no sense to define these separately every time,
because if you hit the

rare case of needing to make a change against that, it's probably just
drive-strength.

I have made this change as per Doug Anderson comment on patch V2 (https://lore.kernel.org/patchwork/patch/1399453/#1598871) And along with drive-strength change, on some of boards Sd card gpio pin also may change right.


diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 0b6f119..eab6f7b 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -24,6 +24,11 @@

 	chosen { };

+	aliases {
+		mmc1 = &sdhc_1;
+		mmc2 = &sdhc_2;
+	};

This is board specific. Something might have a SDIO Wi-Fi card on it.
we are assuming eMMC and SD support available on all boards and if any board supports SDIO Wi-Fi card they can add aliases for SDIO Wi-Fi card in that particular board device DT file.



+			mmc-ddr-1_8v;
+			mmc-hs200-1_8v;
+			mmc-hs400-1_8v;
+			mmc-hs400-enhanced-strobe;

These properties should probably be in the device DT, unless the SoC controller

can only support these speeds and only at 1.8v

we are keeping these flags in SOC file because all platforms would support these modes,
and yes we support only these and at 1.8V.


[1]
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/commit/?h=for-next&id=35a4a8b6e9b133cf3a7d059ad4cf0e24cb4bd029


Konrad



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux