On Mon, 21 Jul 2014, Lorenzo Pieralisi wrote:
> ARM based platforms implement a variety of power management schemes that
> allow processors to enter idle states at run-time.
> The parameters defining these idle states vary on a per-platform basis forcing
> the OS to hardcode the state parameters in platform specific static tables
> whose size grows as the number of platforms supported in the kernel increases
> and hampers device drivers standardization.
>
> Therefore, this patch aims at standardizing idle state device tree bindings
> for ARM platforms. Bindings define idle state parameters inclusive of entry
> methods and state latencies, to allow operating systems to retrieve the
> configuration entries from the device tree and initialize the related power
> management drivers, paving the way for common code in the kernel to deal with
> idle states and removing the need for static data in current and previous
> kernel versions.
>
> ARM64 platforms require the DT to define an entry-method property
> for idle states.
>
> On system implementing PSCI as an enable-method to enter low-power
> states the PSCI CPU suspend method requires the power_state parameter to
> be passed to the PSCI CPU suspend function.
>
> This parameter is specific to a power state and platform specific,
> therefore must be provided by firmware to the OS in order to enable
> proper call sequence.
>
> Thus, this patch also adds a property in the PSCI bindings that
> describes how the PSCI CPU suspend power_state parameter should be
> defined in DT in all device nodes that rely on PSCI CPU suspend method usage.
>
> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@xxxxxxx>
Acked-by: Nicolas Pitre <nico@xxxxxxxxxx>
> ---
> Documentation/devicetree/bindings/arm/cpus.txt | 8 +
> .../devicetree/bindings/arm/idle-states.txt | 679 +++++++++++++++++++++
> Documentation/devicetree/bindings/arm/psci.txt | 14 +-
> 3 files changed, 700 insertions(+), 1 deletion(-)
> create mode 100644 Documentation/devicetree/bindings/arm/idle-states.txt
>
> diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt
> index 1fe72a0..a44d4fd 100644
> --- a/Documentation/devicetree/bindings/arm/cpus.txt
> +++ b/Documentation/devicetree/bindings/arm/cpus.txt
> @@ -215,6 +215,12 @@ nodes to be present and contain the properties described below.
> Value type: <phandle>
> Definition: Specifies the ACC[2] node associated with this CPU.
>
> + - cpu-idle-states
> + Usage: Optional
> + Value type: <prop-encoded-array>
> + Definition:
> + # List of phandles to idle state nodes supported
> + by this cpu [3].
>
> Example 1 (dual-cluster big.LITTLE system 32-bit):
>
> @@ -411,3 +417,5 @@ cpus {
> --
> [1] arm/msm/qcom,saw2.txt
> [2] arm/msm/qcom,kpss-acc.txt
> +[3] ARM Linux kernel documentation - idle states bindings
> + Documentation/devicetree/bindings/arm/idle-states.txt
> diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt
> new file mode 100644
> index 0000000..37375c7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/idle-states.txt
> @@ -0,0 +1,679 @@
> +==========================================
> +ARM idle states binding description
> +==========================================
> +
> +==========================================
> +1 - Introduction
> +==========================================
> +
> +ARM systems contain HW capable of managing power consumption dynamically,
> +where cores can be put in different low-power states (ranging from simple
> +wfi to power gating) according to OS PM policies. The CPU states representing
> +the range of dynamic idle states that a processor can enter at run-time, can be
> +specified through device tree bindings representing the parameters required
> +to enter/exit specific idle states on a given processor.
> +
> +According to the Server Base System Architecture document (SBSA, [3]), the
> +power states an ARM CPU can be put into are identified by the following list:
> +
> +- Running
> +- Idle_standby
> +- Idle_retention
> +- Sleep
> +- Off
> +
> +The power states described in the SBSA document define the basic CPU states on
> +top of which ARM platforms implement power management schemes that allow an OS
> +PM implementation to put the processor in different idle states (which include
> +states listed above; "off" state is not an idle state since it does not have
> +wake-up capabilities, hence it is not considered in this document).
> +
> +Idle state parameters (eg entry latency) are platform specific and need to be
> +characterized with bindings that provide the required information to OS PM
> +code so that it can build the required tables and use them at runtime.
> +
> +The device tree binding definition for ARM idle states is the subject of this
> +document.
> +
> +===========================================
> +2 - idle-states definitions
> +===========================================
> +
> +Idle states are characterized for a specific system through a set of
> +timing and energy related properties, that underline the HW behaviour
> +triggered upon idle states entry and exit.
> +
> +The following diagram depicts the CPU execution phases and related timing
> +properties required to enter and exit an idle state:
> +
> +..__[EXEC]__|__[PREP]__|__[ENTRY]__|__[IDLE]__|__[EXIT]__|__[EXEC]__..
> + | | | | |
> +
> + |<------ entry ------->|
> + | latency |
> + |<- exit ->|
> + | latency |
> + |<-------- min-residency -------->|
> + |<------- wakeup-latency ------->|
> +
> + Diagram 1: CPU idle state execution phases
> +
> +EXEC: Normal CPU execution.
> +
> +PREP: Preparation phase before committing the hardware to idle mode
> + like cache flushing. This is abortable on pending wake-up
> + event conditions. The abort latency is assumed to be negligible
> + (i.e. less than the ENTRY + EXIT duration). If aborted, CPU
> + goes back to EXEC. This phase is optional. If not abortable,
> + this should be included in the ENTRY phase instead.
> +
> +ENTRY: The hardware is committed to idle mode. This period must run
> + to completion up to IDLE before anything else can happen.
> +
> +IDLE: This is the actual energy-saving idle period. This may last
> + between 0 and infinite time, until a wake-up event occurs.
> +
> +EXIT: Period during which the CPU is brought back to operational
> + mode (EXEC).
> +
> +entry-latency: Worst case latency required to enter the idle state. The
> +exit-latency may be guaranteed only after entry-latency has passed.
> +
> +min-residency: Minimum period, including preparation and entry, for a given
> +idle state to be worthwhile energywise.
> +
> +wakeup-latency: Maximum delay between the signaling of a wake-up event and the
> +CPU being able to execute normal code again. If not specified, this is assumed
> +to be entry-latency + exit-latency.
> +
> +These timing parameters can be used by an OS in different circumstances.
> +
> +An idle CPU requires the expected min-residency time to select the most
> +appropriate idle state based on the expected expiry time of the next IRQ
> +(ie wake-up) that causes the CPU to return to the EXEC phase.
> +
> +An operating system scheduler may need to compute the shortest wake-up delay
> +for CPUs in the system by detecting how long will it take to get a CPU out
> +of an idle state, eg:
> +
> +wakeup-delay = exit-latency + max(entry-latency - (now - entry-timestamp), 0)
> +
> +In other words, the scheduler can make its scheduling decision by selecting
> +(eg waking-up) the CPU with the shortest wake-up latency.
> +The wake-up latency must take into account the entry latency if that period
> +has not expired. The abortable nature of the PREP period can be ignored
> +if it cannot be relied upon (e.g. the PREP deadline may occur much sooner than
> +the worst case since it depends on the CPU operating conditions, ie caches
> +state).
> +
> +An OS has to reliably probe the wakeup-latency since some devices can enforce
> +latency constraints guarantees to work properly, so the OS has to detect the
> +worst case wake-up latency it can incur if a CPU is allowed to enter an
> +idle state, and possibly to prevent that to guarantee reliable device
> +functioning.
> +
> +The min-residency time parameter deserves further explanation since it is
> +expressed in time units but must factor in energy consumption coefficients.
> +
> +The energy consumption of a cpu when it enters a power state can be roughly
> +characterised by the following graph:
> +
> + |
> + |
> + |
> + e |
> + n | /---
> + e | /------
> + r | /------
> + g | /-----
> + y | /------
> + | ----
> + | /|
> + | / |
> + | / |
> + | / |
> + | / |
> + | / |
> + |/ |
> + -----|-------+----------------------------------
> + 0| 1 time(ms)
> +
> + Graph 1: Energy vs time example
> +
> +The graph is split in two parts delimited by time 1ms on the X-axis.
> +The graph curve with X-axis values = { x | 0 < x < 1ms } has a steep slope
> +and denotes the energy costs incurred whilst entering and leaving the idle
> +state.
> +The graph curve in the area delimited by X-axis values = {x | x > 1ms } has
> +shallower slope and essentially represents the energy consumption of the idle
> +state.
> +
> +min-residency is defined for a given idle state as the minimum expected
> +residency time for a state (inclusive of preparation and entry) after
> +which choosing that state become the most energy efficient option. A good
> +way to visualise this, is by taking the same graph above and comparing some
> +states energy consumptions plots.
> +
> +For sake of simplicity, let's consider a system with two idle states IDLE1,
> +and IDLE2:
> +
> + |
> + |
> + |
> + | /-- IDLE1
> + e | /---
> + n | /----
> + e | /---
> + r | /-----/--------- IDLE2
> + g | /-------/---------
> + y | ------------ /---|
> + | / /---- |
> + | / /--- |
> + | / /---- |
> + | / /--- |
> + | --- |
> + | / |
> + | / |
> + |/ | time
> + ---/----------------------------+------------------------
> + |IDLE1-energy < IDLE2-energy | IDLE2-energy < IDLE1-energy
> + |
> + IDLE2-min-residency
> +
> + Graph 2: idle states min-residency example
> +
> +In graph 2 above, that takes into account idle states entry/exit energy
> +costs, it is clear that if the idle state residency time (ie time till next
> +wake-up IRQ) is less than IDLE2-min-residency, IDLE1 is the better idle state
> +choice energywise.
> +
> +This is mainly down to the fact that IDLE1 entry/exit energy costs are lower
> +than IDLE2.
> +
> +However, the lower power consumption (ie shallower energy curve slope) of idle
> +state IDLE2 implies that after a suitable time, IDLE2 becomes more energy
> +efficient.
> +
> +The time at which IDLE2 becomes more energy efficient than IDLE1 (and other
> +shallower states in a system with multiple idle states) is defined
> +IDLE2-min-residency and corresponds to the time when energy consumption of
> +IDLE1 and IDLE2 states breaks even.
> +
> +The definitions provided in this section underpin the idle states
> +properties specification that is the subject of the following sections.
> +
> +===========================================
> +3 - idle-states node
> +===========================================
> +
> +ARM processor idle states are defined within the idle-states node, which is
> +a direct child of the cpus node [1] and provides a container where the
> +processor idle states, defined as device tree nodes, are listed.
> +
> +- idle-states node
> +
> + Usage: Optional - On ARM systems, it is a container of processor idle
> + states nodes. If the system does not provide CPU
> + power management capabilities or the processor just
> + supports idle_standby an idle-states node is not
> + required.
> +
> + Description: idle-states node is a container node, where its
> + subnodes describe the CPU idle states.
> +
> + Node name must be "idle-states".
> +
> + The idle-states node's parent node must be the cpus node.
> +
> + The idle-states node's child nodes can be:
> +
> + - one or more state nodes
> +
> + Any other configuration is considered invalid.
> +
> + An idle-states node defines the following properties:
> +
> + - entry-method
> + Value type: <stringlist>
> + Usage and definition depend on ARM architecture version.
> + # On ARM v8 64-bit this property is required and must
> + be one of:
> + - "psci" (see bindings in [2])
> + # On ARM 32-bit systems this property is optional
> +
> +The nodes describing the idle states (state) can only be defined within the
> +idle-states node, any other configuration is considered invalid and therefore
> +must be ignored.
> +
> +===========================================
> +4 - state node
> +===========================================
> +
> +A state node represents an idle state description and must be defined as
> +follows:
> +
> +- state node
> +
> + Description: must be child of the idle-states node
> +
> + The state node name shall follow standard device tree naming
> + rules ([5], 2.2.1 "Node names"), in particular state nodes which
> + are siblings within a single common parent must be given a unique name.
> +
> + The idle state entered by executing the wfi instruction (idle_standby
> + SBSA,[3][4]) is considered standard on all ARM platforms and therefore
> + must not be listed.
> +
> + With the definitions provided above, the following list represents
> + the valid properties for a state node:
> +
> + - compatible
> + Usage: Required
> + Value type: <stringlist>
> + Definition: Must be "arm,idle-state".
> +
> + - local-timer-stop
> + Usage: See definition
> + Value type: <none>
> + Definition: if present the CPU local timer control logic is
> + lost on state entry, otherwise it is retained.
> +
> + - entry-latency-us
> + Usage: Required
> + Value type: <prop-encoded-array>
> + Definition: u32 value representing worst case latency in
> + microseconds required to enter the idle state.
> + The exit-latency-us duration may be guaranteed
> + only after entry-latency-us has passed.
> +
> + - exit-latency-us
> + Usage: Required
> + Value type: <prop-encoded-array>
> + Definition: u32 value representing worst case latency
> + in microseconds required to exit the idle state.
> +
> + - min-residency-us
> + Usage: Required
> + Value type: <prop-encoded-array>
> + Definition: u32 value representing minimum residency duration
> + in microseconds, inclusive of preparation and
> + entry, for this idle state to be considered
> + worthwhile energy wise (refer to section 2 of
> + this document for a complete description).
> +
> + - wakeup-latency-us:
> + Usage: Optional
> + Value type: <prop-encoded-array>
> + Definition: u32 value representing maximum delay between the
> + signaling of a wake-up event and the CPU being
> + able to execute normal code again. If omitted,
> + this is assumed to be equal to:
> +
> + entry-latency-us + exit-latency-us
> +
> + It is important to supply this value on systems
> + where the duration of PREP phase (see diagram 1,
> + section 2) is non-neglibigle.
> + In such systems entry-latency-us + exit-latency-us
> + will exceed wakeup-latency-us by this duration.
> +
> + In addition to the properties listed above, a state node may require
> + additional properties specifics to the entry-method defined in the
> + idle-states node, please refer to the entry-method bindings
> + documentation for properties definitions.
> +
> +===========================================
> +4 - Examples
> +===========================================
> +
> +Example 1 (ARM 64-bit, 16-cpu system, PSCI enable-method):
> +
> +cpus {
> + #size-cells = <0>;
> + #address-cells = <2>;
> +
> + CPU0: cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a57";
> + reg = <0x0 0x0>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0
> + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU1: cpu@1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a57";
> + reg = <0x0 0x1>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0
> + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU2: cpu@100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a57";
> + reg = <0x0 0x100>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0
> + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU3: cpu@101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a57";
> + reg = <0x0 0x101>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0
> + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU4: cpu@10000 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a57";
> + reg = <0x0 0x10000>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0
> + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU5: cpu@10001 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a57";
> + reg = <0x0 0x10001>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0
> + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU6: cpu@10100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a57";
> + reg = <0x0 0x10100>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0
> + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU7: cpu@10101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a57";
> + reg = <0x0 0x10101>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0
> + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU8: cpu@100000000 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x1 0x0>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0
> + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>;
> + };
> +
> + CPU9: cpu@100000001 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x1 0x1>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0
> + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>;
> + };
> +
> + CPU10: cpu@100000100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x1 0x100>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0
> + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>;
> + };
> +
> + CPU11: cpu@100000101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x1 0x101>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0
> + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>;
> + };
> +
> + CPU12: cpu@100010000 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x1 0x10000>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0
> + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>;
> + };
> +
> + CPU13: cpu@100010001 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x1 0x10001>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0
> + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>;
> + };
> +
> + CPU14: cpu@100010100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x1 0x10100>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0
> + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>;
> + };
> +
> + CPU15: cpu@100010101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x1 0x10101>;
> + enable-method = "psci";
> + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0
> + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>;
> + };
> +
> + idle-states {
> + entry-method = "arm,psci";
> +
> + CPU_RETENTION_0_0: cpu-retention-0-0 {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x0010000>;
> + entry-latency-us = <20>;
> + exit-latency-us = <40>;
> + min-residency-us = <80>;
> + };
> +
> + CLUSTER_RETENTION_0: cluster-retention-0 {
> + compatible = "arm,idle-state";
> + local-timer-stop;
> + arm,psci-suspend-param = <0x1010000>;
> + entry-latency-us = <50>;
> + exit-latency-us = <100>;
> + min-residency-us = <250>;
> + wakeup-latency-us = <130>;
> + };
> +
> + CPU_SLEEP_0_0: cpu-sleep-0-0 {
> + compatible = "arm,idle-state";
> + local-timer-stop;
> + arm,psci-suspend-param = <0x0010000>;
> + entry-latency-us = <250>;
> + exit-latency-us = <500>;
> + min-residency-us = <950>;
> + };
> +
> + CLUSTER_SLEEP_0: cluster-sleep-0 {
> + compatible = "arm,idle-state";
> + local-timer-stop;
> + arm,psci-suspend-param = <0x1010000>;
> + entry-latency-us = <600>;
> + exit-latency-us = <1100>;
> + min-residency-us = <2700>;
> + wakeup-latency-us = <1500>;
> + };
> +
> + CPU_RETENTION_1_0: cpu-retention-1-0 {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x0010000>;
> + entry-latency-us = <20>;
> + exit-latency-us = <40>;
> + min-residency-us = <90>;
> + };
> +
> + CLUSTER_RETENTION_1: cluster-retention-1 {
> + compatible = "arm,idle-state";
> + local-timer-stop;
> + arm,psci-suspend-param = <0x1010000>;
> + entry-latency-us = <50>;
> + exit-latency-us = <100>;
> + min-residency-us = <270>;
> + wakeup-latency-us = <100>;
> + };
> +
> + CPU_SLEEP_1_0: cpu-sleep-1-0 {
> + compatible = "arm,idle-state";
> + local-timer-stop;
> + arm,psci-suspend-param = <0x0010000>;
> + entry-latency-us = <70>;
> + exit-latency-us = <100>;
> + min-residency-us = <300>;
> + wakeup-latency-us = <150>;
> + };
> +
> + CLUSTER_SLEEP_1: cluster-sleep-1 {
> + compatible = "arm,idle-state";
> + local-timer-stop;
> + arm,psci-suspend-param = <0x1010000>;
> + entry-latency-us = <500>;
> + exit-latency-us = <1200>;
> + min-residency-us = <3500>;
> + wakeup-latency-us = <1300>;
> + };
> + };
> +
> +};
> +
> +Example 2 (ARM 32-bit, 8-cpu system, two clusters):
> +
> +cpus {
> + #size-cells = <0>;
> + #address-cells = <1>;
> +
> + CPU0: cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a15";
> + reg = <0x0>;
> + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU1: cpu@1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a15";
> + reg = <0x1>;
> + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU2: cpu@2 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a15";
> + reg = <0x2>;
> + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU3: cpu@3 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a15";
> + reg = <0x3>;
> + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>;
> + };
> +
> + CPU4: cpu@100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a7";
> + reg = <0x100>;
> + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>;
> + };
> +
> + CPU5: cpu@101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a7";
> + reg = <0x101>;
> + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>;
> + };
> +
> + CPU6: cpu@102 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a7";
> + reg = <0x102>;
> + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>;
> + };
> +
> + CPU7: cpu@103 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a7";
> + reg = <0x103>;
> + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>;
> + };
> +
> + idle-states {
> + CPU_SLEEP_0_0: cpu-sleep-0-0 {
> + compatible = "arm,idle-state";
> + local-timer-stop;
> + entry-latency-us = <200>;
> + exit-latency-us = <100>;
> + min-residency-us = <400>;
> + wakeup-latency-us = <250>;
> + };
> +
> + CLUSTER_SLEEP_0: cluster-sleep-0 {
> + compatible = "arm,idle-state";
> + local-timer-stop;
> + entry-latency-us = <500>;
> + exit-latency-us = <1500>;
> + min-residency-us = <2500>;
> + wakeup-latency-us = <1700>;
> + };
> +
> + CPU_SLEEP_1_0: cpu-sleep-1-0 {
> + compatible = "arm,idle-state";
> + local-timer-stop;
> + entry-latency-us = <300>;
> + exit-latency-us = <500>;
> + min-residency-us = <900>;
> + wakeup-latency-us = <600>;
> + };
> +
> + CLUSTER_SLEEP_1: cluster-sleep-1 {
> + compatible = "arm,idle-state";
> + local-timer-stop;
> + entry-latency-us = <800>;
> + exit-latency-us = <2000>;
> + min-residency-us = <6500>;
> + wakeup-latency-us = <2300>;
> + };
> + };
> +
> +};
> +
> +===========================================
> +5 - References
> +===========================================
> +
> +[1] ARM Linux Kernel documentation - CPUs bindings
> + Documentation/devicetree/bindings/arm/cpus.txt
> +
> +[2] ARM Linux Kernel documentation - PSCI bindings
> + Documentation/devicetree/bindings/arm/psci.txt
> +
> +[3] ARM Server Base System Architecture (SBSA)
> + http://infocenter.arm.com/help/index.jsp
> +
> +[4] ARM Architecture Reference Manuals
> + http://infocenter.arm.com/help/index.jsp
> +
> +[5] ePAPR standard
> + https://www.power.org/documentation/epapr-version-1-1/
> diff --git a/Documentation/devicetree/bindings/arm/psci.txt b/Documentation/devicetree/bindings/arm/psci.txt
> index b4a58f3..5aa40ed 100644
> --- a/Documentation/devicetree/bindings/arm/psci.txt
> +++ b/Documentation/devicetree/bindings/arm/psci.txt
> @@ -50,6 +50,16 @@ Main node optional properties:
>
> - migrate : Function ID for MIGRATE operation
>
> +Device tree nodes that require usage of PSCI CPU_SUSPEND function (ie idle
> +state nodes, as per bindings in [1]) must specify the following properties:
> +
> +- arm,psci-suspend-param
> + Usage: Required for state nodes[1] if the corresponding
> + idle-states node entry-method property is set
> + to "psci".
> + Value type: <u32>
> + Definition: power_state parameter to pass to the PSCI
> + suspend call.
>
> Example:
>
> @@ -64,7 +74,6 @@ Case 1: PSCI v0.1 only.
> migrate = <0x95c10003>;
> };
>
> -
> Case 2: PSCI v0.2 only
>
> psci {
> @@ -88,3 +97,6 @@ Case 3: PSCI v0.2 and PSCI v0.1.
>
> ...
> };
> +
> +[1] Kernel documentation - ARM idle states bindings
> + Documentation/devicetree/bindings/arm/idle-states.txt
> --
> 1.9.1
>
>
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
