Add the VDO definition for USB PD rev 2.0 in the bindings and define a
new property snk-vdos-v1 containing legacy VDOs as the responses to the
port partner which only supports PD rev 2.0.
Signed-off-by: Kyle Tso <kyletso@xxxxxxxxxx>
---
changes since v2:
- no change
.../bindings/connector/usb-connector.yaml | 15 ++++
include/dt-bindings/usb/pd.h | 69 ++++++++++++++++++-
2 files changed, 81 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/connector/usb-connector.yaml b/Documentation/devicetree/bindings/connector/usb-connector.yaml
index 32509b98142e..92b49bc37939 100644
--- a/Documentation/devicetree/bindings/connector/usb-connector.yaml
+++ b/Documentation/devicetree/bindings/connector/usb-connector.yaml
@@ -149,6 +149,17 @@ properties:
maxItems: 6
$ref: /schemas/types.yaml#/definitions/uint32-array
+ sink-vdos-v1:
+ description: An array of u32 with each entry, a Vendor Defined Message Object (VDO),
+ providing additional information corresponding to the product, the detailed bit
+ definitions and the order of each VDO can be found in
+ "USB Power Delivery Specification Revision 2.0, Version 1.3" chapter 6.4.4.3.1 Discover
+ Identity. User can specify the VDO array via VDO_IDH/_CERT/_PRODUCT/_CABLE/_AMA defined in
+ dt-bindings/usb/pd.h.
+ minItems: 3
+ maxItems: 6
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+
op-sink-microwatt:
description: Sink required operating power in microwatt, if source can't
offer the power, Capability Mismatch is set. Required for power sink and
@@ -207,6 +218,10 @@ properties:
SNK_READY for non-pd link.
type: boolean
+dependencies:
+ sink-vdos-v1: [ 'sink-vdos' ]
+ sink-vdos: [ 'sink-vdos-v1' ]
+
required:
- compatible
diff --git a/include/dt-bindings/usb/pd.h b/include/dt-bindings/usb/pd.h
index fef3ef65967f..9e47f9673405 100644
--- a/include/dt-bindings/usb/pd.h
+++ b/include/dt-bindings/usb/pd.h
@@ -106,6 +106,10 @@
* <20:16> :: Reserved, Shall be set to zero
* <15:0> :: USB-IF assigned VID for this cable vendor
*/
+
+/* PD Rev2.0 definition */
+#define IDH_PTYPE_UNDEF 0
+
/* SOP Product Type (UFP) */
#define IDH_PTYPE_NOT_UFP 0
#define IDH_PTYPE_HUB 1
@@ -228,7 +232,25 @@
| ((pnum) & 0x1f))
/*
- * Passive Cable VDO
+ * Cable VDO (for both Passive and Active Cable VDO in PD Rev2.0)
+ * ---------
+ * <31:28> :: Cable HW version
+ * <27:24> :: Cable FW version
+ * <23:20> :: Reserved, Shall be set to zero
+ * <19:18> :: type-C to Type-A/B/C/Captive (00b == A, 01 == B, 10 == C, 11 == Captive)
+ * <17> :: Reserved, Shall be set to zero
+ * <16:13> :: cable latency (0001 == <10ns(~1m length))
+ * <12:11> :: cable termination type (11b == both ends active VCONN req)
+ * <10> :: SSTX1 Directionality support (0b == fixed, 1b == cfgable)
+ * <9> :: SSTX2 Directionality support
+ * <8> :: SSRX1 Directionality support
+ * <7> :: SSRX2 Directionality support
+ * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A)
+ * <4> :: Vbus through cable (0b == no, 1b == yes)
+ * <3> :: SOP" controller present? (0b == no, 1b == yes)
+ * <2:0> :: USB SS Signaling support
+ *
+ * Passive Cable VDO (PD Rev3.0+)
* ---------
* <31:28> :: Cable HW version
* <27:24> :: Cable FW version
@@ -244,7 +266,7 @@
* <4:3> :: Reserved, Shall be set to zero
* <2:0> :: USB highest speed
*
- * Active Cable VDO 1
+ * Active Cable VDO 1 (PD Rev3.0+)
* ---------
* <31:28> :: Cable HW version
* <27:24> :: Cable FW version
@@ -266,7 +288,9 @@
#define CABLE_VDO_VER1_0 0
#define CABLE_VDO_VER1_3 3
-/* Connector Type */
+/* Connector Type (_ATYPE and _BTYPE are for PD Rev2.0 only) */
+#define CABLE_ATYPE 0
+#define CABLE_BTYPE 1
#define CABLE_CTYPE 2
#define CABLE_CAPTIVE 3
@@ -303,12 +327,22 @@
#define CABLE_CURR_3A 1
#define CABLE_CURR_5A 2
+/* USB SuperSpeed Signaling Support (PD Rev2.0) */
+#define CABLE_USBSS_U2_ONLY 0
+#define CABLE_USBSS_U31_GEN1 1
+#define CABLE_USBSS_U31_GEN2 2
+
/* USB Highest Speed */
#define CABLE_USB2_ONLY 0
#define CABLE_USB32_GEN1 1
#define CABLE_USB32_4_GEN2 2
#define CABLE_USB4_GEN3 3
+#define VDO_CABLE(hw, fw, cbl, lat, term, tx1d, tx2d, rx1d, rx2d, cur, vps, sopp, usbss) \
+ (((hw) & 0x7) << 28 | ((fw) & 0x7) << 24 | ((cbl) & 0x3) << 18 \
+ | ((lat) & 0x7) << 13 | ((term) & 0x3) << 11 | (tx1d) << 10 \
+ | (tx2d) << 9 | (rx1d) << 8 | (rx2d) << 7 | ((cur) & 0x3) << 5 \
+ | (vps) << 4 | (sopp) << 3 | ((usbss) & 0x7))
#define VDO_PCABLE(hw, fw, ver, conn, lat, term, vbm, cur, spd) \
(((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21 \
| ((conn) & 0x3) << 18 | ((lat) & 0xf) << 13 | ((term) & 0x3) << 11 \
@@ -373,6 +407,35 @@
| ((hops) & 0x3) << 6 | (u2) << 5 | (u32) << 4 | (lane) << 3 \
| (iso) << 2 | (gen))
+/*
+ * AMA VDO (PD Rev2.0)
+ * ---------
+ * <31:28> :: Cable HW version
+ * <27:24> :: Cable FW version
+ * <23:12> :: Reserved, Shall be set to zero
+ * <11> :: SSTX1 Directionality support (0b == fixed, 1b == cfgable)
+ * <10> :: SSTX2 Directionality support
+ * <9> :: SSRX1 Directionality support
+ * <8> :: SSRX2 Directionality support
+ * <7:5> :: Vconn power
+ * <4> :: Vconn power required
+ * <3> :: Vbus power required
+ * <2:0> :: USB SS Signaling support
+ */
+#define VDO_AMA(hw, fw, tx1d, tx2d, rx1d, rx2d, vcpwr, vcr, vbr, usbss) \
+ (((hw) & 0x7) << 28 | ((fw) & 0x7) << 24 \
+ | (tx1d) << 11 | (tx2d) << 10 | (rx1d) << 9 | (rx2d) << 8 \
+ | ((vcpwr) & 0x7) << 5 | (vcr) << 4 | (vbr) << 3 \
+ | ((usbss) & 0x7))
+
+#define PD_VDO_AMA_VCONN_REQ(vdo) (((vdo) >> 4) & 1)
+#define PD_VDO_AMA_VBUS_REQ(vdo) (((vdo) >> 3) & 1)
+
+#define AMA_USBSS_U2_ONLY 0
+#define AMA_USBSS_U31_GEN1 1
+#define AMA_USBSS_U31_GEN2 2
+#define AMA_USBSS_BBONLY 3
+
/*
* VPD VDO
* ---------
--
2.32.0.rc0.204.g9fa02ecfa5-goog
