UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1]. Add support by removing the no-1-8-v tag and including the voltage regulator device tree nodes for power cycling. However, the 4 bit interface of AM65 SR 1.0 cannot be supported at 3.3 V or 1.8 V because of erratas i2025 and i2026 [2]. As the SD card is the primary boot mode for development usecases, continue to enable SD card and disable UHS-I modes in it to minimize any ageing issues happening because of erratas. k3-am6528-iot2050-basic and k3-am6548-iot2050-advanced boards use S.R. 1.0 version of AM65 SoC. Therefore, add no-1-8-v in sdhci1 device tree node of the common iot2050 device tree file. [1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1 [2] - https://www.ti.com/lit/er/sprz452e/sprz452e.pdf Signed-off-by: Aswath Govindraju <a-govindraju@xxxxxx> Acked-by: Jan Kiszka <jan.kiszka@xxxxxxxxxxx> --- KPV test report: - https://pastebin.ubuntu.com/p/wnQQTrJZP6/ changes since v3: - rebased on top of https://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux.git/log/?h=ti-k3-dts-next - Picked up Jan's ack changes since v2: - moved the no-1-8-v tag to common iot2050 dtsi file. changes since v1: - added no-1-8-v tag in sdhci1 dt nodes of k3-am6528-iot2050-basic and k3-am6548-iot2050-advanced boards as they use S.R.1.0 version AM65 SoC. .../boot/dts/ti/k3-am65-iot2050-common.dtsi | 1 + arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 1 - .../arm64/boot/dts/ti/k3-am654-base-board.dts | 33 +++++++++++++++++++ 3 files changed, 34 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi index f4ec9ed52939..d90abda1de84 100644 --- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi @@ -555,6 +555,7 @@ pinctrl-0 = <&main_mmc1_pins_default>; ti,driver-strength-ohm = <50>; disable-wp; + no-1-8-v; }; &usb0 { diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi index 6cd3131eb9ff..f97fc00c00ca 100644 --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi @@ -301,7 +301,6 @@ ti,otap-del-sel = <0x2>; ti,trm-icp = <0x8>; dma-coherent; - no-1-8-v; }; scm_conf: scm-conf@100000 { diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts index 97c344088483..60e43fd7af12 100644 --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts @@ -85,6 +85,38 @@ gpios = <&wkup_gpio0 27 GPIO_ACTIVE_LOW>; }; }; + + evm_12v0: fixedregulator-evm12v0 { + /* main supply */ + compatible = "regulator-fixed"; + regulator-name = "evm_12v0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc3v3_io: fixedregulator-vcc3v3io { + /* Output of TPS54334 */ + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&evm_12v0>; + }; + + vdd_mmc1_sd: fixedregulator-sd { + compatible = "regulator-fixed"; + regulator-name = "vdd_mmc1_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + vin-supply = <&vcc3v3_io>; + gpio = <&pca9554 4 GPIO_ACTIVE_HIGH>; + }; }; &wkup_pmx0 { @@ -327,6 +359,7 @@ * disable sdhci1 */ &sdhci1 { + vmmc-supply = <&vdd_mmc1_sd>; pinctrl-names = "default"; pinctrl-0 = <&main_mmc1_pins_default>; ti,driver-strength-ohm = <50>; -- 2.17.1
