On 11.05.21 18:48, Aswath Govindraju wrote: > UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1]. > > Add support by removing the no-1-8-v tag and including the voltage > regulator device tree nodes for power cycling. > > However, the 4 bit interface of AM65 SR 1.0 cannot be supported at 3.3 V or > 1.8 V because of erratas i2025 and i2026 [2]. As the SD card is the primary > boot mode for development usecases, continue to enable SD card and disable > UHS-I modes in it to minimize any ageing issues happening because of > erratas. > > k3-am6528-iot2050-basic and k3-am6548-iot2050-advanced boards use S.R. 1.0 > version of AM65 SoC. Therefore, add no-1-8-v in sdhci1 device tree node of > the common iot2050 device tree file. > > [1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1 > [2] - https://www.ti.com/lit/er/sprz452e/sprz452e.pdf > > Signed-off-by: Aswath Govindraju <a-govindraju@xxxxxx> > --- > > changes since v2: > - moved the no-1-8-v tag to common iot2050 dtsi file. > > changes since v1: > - added no-1-8-v tag in sdhci1 dt nodes of k3-am6528-iot2050-basic and > k3-am6548-iot2050-advanced boards as they use S.R.1.0 version AM65 SoC. > > .../boot/dts/ti/k3-am65-iot2050-common.dtsi | 1 + > arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 1 - > .../arm64/boot/dts/ti/k3-am654-base-board.dts | 33 +++++++++++++++++++ > 3 files changed, 34 insertions(+), 1 deletion(-) > > diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi > index de763ca9251c..46cc348cd4be 100644 > --- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi > +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi > @@ -555,6 +555,7 @@ > pinctrl-0 = <&main_mmc1_pins_default>; > ti,driver-strength-ohm = <50>; > disable-wp; > + no-1-8-v; > }; > Acked-by: Jan Kiszka <jan.kiszka@xxxxxxxxxxx> Jan > &usb0 { > diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi > index cb340d1b401f..632f32fce4a1 100644 > --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi > +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi > @@ -301,7 +301,6 @@ > ti,otap-del-sel = <0x2>; > ti,trm-icp = <0x8>; > dma-coherent; > - no-1-8-v; > }; > > scm_conf: scm-conf@100000 { > diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts > index 9e87fb313a54..51c594b4dddb 100644 > --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts > +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts > @@ -91,6 +91,38 @@ > #clock-cells = <0>; > clock-frequency = <24000000>; > }; > + > + evm_12v0: fixedregulator-evm12v0 { > + /* main supply */ > + compatible = "regulator-fixed"; > + regulator-name = "evm_12v0"; > + regulator-min-microvolt = <12000000>; > + regulator-max-microvolt = <12000000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + vcc3v3_io: fixedregulator-vcc3v3io { > + /* Output of TPS54334 */ > + compatible = "regulator-fixed"; > + regulator-name = "vcc3v3_io"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + regulator-boot-on; > + vin-supply = <&evm_12v0>; > + }; > + > + vdd_mmc1_sd: fixedregulator-sd { > + compatible = "regulator-fixed"; > + regulator-name = "vdd_mmc1_sd"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + enable-active-high; > + vin-supply = <&vcc3v3_io>; > + gpio = <&pca9554 4 GPIO_ACTIVE_HIGH>; > + }; > }; > > &wkup_pmx0 { > @@ -350,6 +382,7 @@ > * disable sdhci1 > */ > &sdhci1 { > + vmmc-supply = <&vdd_mmc1_sd>; > pinctrl-names = "default"; > pinctrl-0 = <&main_mmc1_pins_default>; > ti,driver-strength-ohm = <50>; > -- Siemens AG, T RDA IOT Corporate Competence Center Embedded Linux
