Hi Rob,
Thank you for the patch.
On Tue, May 18, 2021 at 06:28:57PM -0500, Rob Herring wrote:
> Cc: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> Signed-off-by: Rob Herring <robh@xxxxxxxxxx>
> ---
> .../bindings/i2c/i2c-mux-pca954x.txt | 74 ------------
> .../bindings/i2c/i2c-mux-pca954x.yaml | 106 ++++++++++++++++++
> 2 files changed, 106 insertions(+), 74 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
> create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
>
> diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
> deleted file mode 100644
> index 9f3f3eb67e87..000000000000
> --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
> +++ /dev/null
> @@ -1,74 +0,0 @@
> -* NXP PCA954x I2C bus switch
> -
> -The driver supports NXP PCA954x and PCA984x I2C mux/switch devices.
> -
> -Required Properties:
> -
> - - compatible: Must contain one of the following.
> - "nxp,pca9540",
> - "nxp,pca9542",
> - "nxp,pca9543",
> - "nxp,pca9544",
> - "nxp,pca9545",
> - "nxp,pca9546", "nxp,pca9846",
> - "nxp,pca9547", "nxp,pca9847",
> - "nxp,pca9548", "nxp,pca9848",
> - "nxp,pca9849"
> -
> - - reg: The I2C address of the device.
> -
> - The following required properties are defined externally:
> -
> - - Standard I2C mux properties. See i2c-mux.txt in this directory.
> - - I2C child bus nodes. See i2c-mux.txt in this directory.
> -
> -Optional Properties:
> -
> - - reset-gpios: Reference to the GPIO connected to the reset input.
> - - idle-state: if present, overrides i2c-mux-idle-disconnect,
> - Please refer to Documentation/devicetree/bindings/mux/mux-controller.yaml
> - - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all
> - children in idle state. This is necessary for example, if there are several
> - multiplexers on the bus and the devices behind them use same I2C addresses.
> - - interrupts: Interrupt mapping for IRQ.
> - - interrupt-controller: Marks the device node as an interrupt controller.
> - - #interrupt-cells : Should be two.
> - - first cell is the pin number
> - - second cell is used to specify flags.
> - See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> -
> -Example:
> -
> - i2c-switch@74 {
> - compatible = "nxp,pca9548";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - reg = <0x74>;
> -
> - interrupt-parent = <&ipic>;
> - interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
> - interrupt-controller;
> - #interrupt-cells = <2>;
> -
> - i2c@2 {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - reg = <2>;
> -
> - eeprom@54 {
> - compatible = "atmel,24c08";
> - reg = <0x54>;
> - };
> - };
> -
> - i2c@4 {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - reg = <4>;
> -
> - rtc@51 {
> - compatible = "nxp,pcf8563";
> - reg = <0x51>;
> - };
> - };
> - };
> diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
> new file mode 100644
> index 000000000000..82d9101098c7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
> @@ -0,0 +1,106 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/i2c/i2c-mux-pca954x.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: NXP PCA954x I2C bus switch
> +
> +maintainers:
> + - Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> +
> +description:
> + The binding supports NXP PCA954x and PCA984x I2C mux/switch devices.
> +
> +allOf:
> + - $ref: /schemas/i2c/i2c-mux.yaml#
> +
> +properties:
> + compatible:
> + enum:
> + - nxp,pca9540
> + - nxp,pca9542
> + - nxp,pca9543
> + - nxp,pca9544
> + - nxp,pca9545
> + - nxp,pca9546
> + - nxp,pca9547
> + - nxp,pca9548
> + - nxp,pca9849
I'd put this entry last to keep them alphabetically sorted.
While at it, could you add nxp,pca9646 as the driver supports it ?
Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> + - nxp,pca9846
> + - nxp,pca9847
> + - nxp,pca9848
> +
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + maxItems: 1
> +
> + "#interrupt-cells":
> + const: 2
> +
> + interrupt-controller: true
> +
> + reset-gpios:
> + maxItems: 1
> +
> + i2c-mux-idle-disconnect:
> + type: boolean
> + description: Forces mux to disconnect all children in idle state. This is
> + necessary for example, if there are several multiplexers on the bus and
> + the devices behind them use same I2C addresses.
> +
> + idle-state:
> + description: if present, overrides i2c-mux-idle-disconnect
> + $ref: /schemas/mux/mux-controller.yaml#/properties/idle-state
> +
> +required:
> + - compatible
> + - reg
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/irq.h>
> +
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c-mux@74 {
> + compatible = "nxp,pca9548";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x74>;
> +
> + interrupt-parent = <&ipic>;
> + interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> +
> + eeprom@54 {
> + compatible = "atmel,24c08";
> + reg = <0x54>;
> + };
> + };
> +
> + i2c@4 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <4>;
> +
> + rtc@51 {
> + compatible = "nxp,pcf8563";
> + reg = <0x51>;
> + };
> + };
> + };
> + };
> +...
--
Regards,
Laurent Pinchart
