On Wed, Jul 16, 2014 at 1:13 PM, Grygorii Strashko <grygorii.strashko@xxxxxx> wrote: > The similar MDIO HW blocks is used by keystone 2 SoCs as > in Davinci SoCs: > - one in Gigabit Ethernet (GbE) Switch Subsystem > See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf > - one in 10 Gigabit Ethernet Subsystem > See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf > > Hence, reuse Davinci MDIO driver for Keystone 2 and > enable TI networking for Keystone 2 devices > > Reviewed-by: Santosh Shilimkar <santosh.shilimkar@xxxxxx> > Acked-by: Mugunthan V N <mugunthanvnm@xxxxxx> > Signed-off-by: Grygorii Strashko <grygorii.strashko@xxxxxx> Reviewed-by: Lad, Prabhakar <prabhakar.csengg@xxxxxxxxx> Thanks, --Prabhakar Lad > --- > .../devicetree/bindings/net/davinci-mdio.txt | 8 ++++---- > drivers/net/ethernet/ti/Kconfig | 4 ++-- > 2 files changed, 6 insertions(+), 6 deletions(-) > > diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt > index 72efaaf..0369e25 100644 > --- a/Documentation/devicetree/bindings/net/davinci-mdio.txt > +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt > @@ -1,8 +1,8 @@ > -TI SoC Davinci MDIO Controller Device Tree Bindings > +TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings > --------------------------------------------------- > > Required properties: > -- compatible : Should be "ti,davinci_mdio" > +- compatible : Should be "ti,davinci_mdio" or "ti,keystone_mdio" > - reg : physical base address and size of the davinci mdio > registers map > - bus_freq : Mdio Bus frequency > @@ -19,7 +19,7 @@ file. > Examples: > > mdio: davinci_mdio@4A101000 { > - compatible = "ti,cpsw"; > + compatible = "ti,davinci_mdio"; > reg = <0x4A101000 0x1000>; > bus_freq = <1000000>; > }; > @@ -27,7 +27,7 @@ Examples: > (or) > > mdio: davinci_mdio@4A101000 { > - compatible = "ti,cpsw"; > + compatible = "ti,davinci_mdio"; > ti,hwmods = "davinci_mdio"; > bus_freq = <1000000>; > }; > diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig > index 53150c2..1769700 100644 > --- a/drivers/net/ethernet/ti/Kconfig > +++ b/drivers/net/ethernet/ti/Kconfig > @@ -5,7 +5,7 @@ > config NET_VENDOR_TI > bool "Texas Instruments (TI) devices" > default y > - depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX)) > + depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE)) > ---help--- > If you have a network (Ethernet) card belonging to this class, say Y > and read the Ethernet-HOWTO, available from > @@ -32,7 +32,7 @@ config TI_DAVINCI_EMAC > > config TI_DAVINCI_MDIO > tristate "TI DaVinci MDIO Support" > - depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX ) > + depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE ) > select PHYLIB > ---help--- > This driver supports TI's DaVinci MDIO module. > -- > 1.7.9.5 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
