Hi, On 07/16/2014 09:18 AM, Jassi Brar wrote: > On 16 July 2014 19:38, Arnd Bergmann <arnd@xxxxxxxx> wrote: >> On Wednesday 16 July 2014 18:42:22 Jassi Brar wrote: >>> On 16 July 2014 18:39, Arnd Bergmann <arnd@xxxxxxxx> wrote: >>>> On Wednesday 16 July 2014 18:35:33 Jassi Brar wrote: >>>>> On 16 July 2014 18:15, Arnd Bergmann <arnd@xxxxxxxx> wrote: >>>>>> On Wednesday 16 July 2014 18:07:04 Jassi Brar wrote: >>>>>>> On 16 July 2014 15:46, Arnd Bergmann <arnd@xxxxxxxx> wrote: >>>>>>>> On Wednesday 16 July 2014 10:40:19 Sudeep Holla wrote: >>>>>>>>>> + >>>>>>>>>> +Required property: >>>>>>>>>> +- mbox: List of phandle and mailbox channel specifier. >>>>>>>>>> + >>>>>>>>>> +- mbox-names: List of identifier strings for each mailbox channel >>>>>>>>>> + required by the client. >>>>>>>>>> + >>>>>>>>> >>>>>>>>> IMO the mailbox names are more associated with the controller channels/ >>>>>>>>> mailbox rather than the clients using it. Does it make sense to move >>>>>>>>> this under controller. It also avoid each client replicating the names. >>>>>>>> >>>>>>>> I think it would be best to just make the mbox-names property optional, >>>>>>>> like we have for other subsystems. >>>>>>>> >>>>>>> A very similar subsystem - DMAEngine also has 'dma-names' as a >>>>>>> required property. >>>>>>> >>>>>>> If a client is assigned only 1 mbox in DT, we can do without >>>>>>> mbox-names. But I am not sure what to do if a client needs two or more >>>>>>> differently capable mboxes? Simply allocating in order of mbox request >>>>>>> doesn't seem very robust. >>>>>> >>>>>> Traditionally, these things (regs, interrupts, ...) are just accessed >>>>>> by index. The reason why dmaengine requires the name is that some machines >>>>>> can use multiple DMA engine devices attached to the same request line, >>>>>> so the dmaengine subsystem can pick any of them that has a matching >>>>>> name. >>>>> And also, I think, when a client needs 2 different dma channels, say >>>>> for RX and TX each. The api can't assign the first channel specified >>>>> in 'dmas' property to the first channel request that comes to it, >>>>> unless we assume client driver always requests dma channels in the >>>>> order written in its DT node. And this is the main reason I see for >>>>> having mbox-names property. >>>> >>>> Most subsystems require passing an explicit index in this case. >>>> >>>>> If we make mbox-names optional, do we assume client driver must >>>>> request mbox in the order specified in its DT node? >>>> >>>> Correct. >>>> >>> OK. So how about we drop mbox-names altogether and expect client >>> driver to simply provide an index of the mbox needed? >> >> That would be fine with me, but I think a lot of people like >> the idea of identifying things by name, and are used to that >> from the other subsystems. >> >> Maybe you can leave the mbox-names property defined as 'optional' >> in the generic mbox binding but remove the code in Linux? That way >> we can always put it back at a later point without changing the >> binding in an incompatible way. I like this too, especially given that the framework uses this only to retrieve the index. The mbox_client structure currently requires the chan_name to be filled in, which means both the client driver and the framework end up having to parse the property. While we are at this, how about we change the property name from "mbox" to a plural-form "mboxes" to be inline with gpios, dmas etc. regards Suman >> >> Individual mailbox clients can mandate specific strings. >> > Sounds great. > > Thanks > Jassi > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
