On Mon, Apr 26, 2021 at 06:50:15PM +0800, ChiYuan Huang wrote: > Hi, > > Daniel Thompson <daniel.thompson@xxxxxxxxxx> 於 2021年4月26日 週一 下午6:19寫道： > > > > On Mon, Apr 26, 2021 at 03:18:11PM +0800, cy_huang wrote: > > > From: ChiYuan Huang <cy_huang@xxxxxxxxxxx> > > > > > > Adds support for Richtek RT4831 backlight. > > > > > > Signed-off-by: ChiYuan Huang <cy_huang@xxxxxxxxxxx> > > > Reviewed-by: Daniel Thompson <daniel.thompson@xxxxxxxxxx> > > > --- > > > Resend this v6 patch series to loop devicetree reviewers. > > > > > > For next, if the typo in Kconfig 'common' to 'commonly' can be added the below line > > > Reviewed-by: Daniel Thompson <daniel.thompson@xxxxxxxxxx> > > > --- > > > > This isn't the best way to handle feedback from multiple maintainers. > > > > It is great to see you are keeping track of feedback. However it doesn't > > make sense to RESEND an old patchset and acknowledge that you haven't > > fixed a typo yet. > > > > It would be better to fix the typo and to resend a v7. > > You can refer to the below reply > https://lkml.org/lkml/2021/4/23/229 Indeed. However that thread is ambiguous about resending with changes (PATCH v7) and resending without changes (PATCH RESEND v6). Given you said in March there was a v7 series coming, I think it would have been better to send a new version. Don't worry about this too much. This is turning into quite a lot of fuss for a two letter typo. However it's very unusual to send out a patch (except perhaps an RFC) together with a comment listing what you need to fix next time around. It is pretty much always better to fix it first and then send it. Daniel. > > > drivers/video/backlight/Kconfig | 8 ++ > > > drivers/video/backlight/Makefile | 1 + > > > drivers/video/backlight/rt4831-backlight.c | 203 +++++++++++++++++++++++++++++ > > > 3 files changed, 212 insertions(+) > > > create mode 100644 drivers/video/backlight/rt4831-backlight.c > > > > > > diff --git a/drivers/video/backlight/Kconfig b/drivers/video/backlight/Kconfig > > > index d83c87b..de96441 100644 > > > --- a/drivers/video/backlight/Kconfig > > > +++ b/drivers/video/backlight/Kconfig > > > @@ -289,6 +289,14 @@ config BACKLIGHT_QCOM_WLED > > > If you have the Qualcomm PMIC, say Y to enable a driver for the > > > WLED block. Currently it supports PM8941 and PMI8998. > > > > > > +config BACKLIGHT_RT4831 > > > + tristate "Richtek RT4831 Backlight Driver" > > > + depends on MFD_RT4831 > > > + help > > > + This enables support for Richtek RT4831 Backlight driver. > > > + It's common used to drive the display WLED. There're four channels > > > + inisde, and each channel can provide up to 30mA current. > > > + > > > config BACKLIGHT_SAHARA > > > tristate "Tabletkiosk Sahara Touch-iT Backlight Driver" > > > depends on X86 > > > diff --git a/drivers/video/backlight/Makefile b/drivers/video/backlight/Makefile > > > index 685f3f1..cae2c83 100644 > > > --- a/drivers/video/backlight/Makefile > > > +++ b/drivers/video/backlight/Makefile > > > @@ -49,6 +49,7 @@ obj-$(CONFIG_BACKLIGHT_PANDORA) += pandora_bl.o > > > obj-$(CONFIG_BACKLIGHT_PCF50633) += pcf50633-backlight.o > > > obj-$(CONFIG_BACKLIGHT_PWM) += pwm_bl.o > > > obj-$(CONFIG_BACKLIGHT_QCOM_WLED) += qcom-wled.o > > > +obj-$(CONFIG_BACKLIGHT_RT4831) += rt4831-backlight.o > > > obj-$(CONFIG_BACKLIGHT_SAHARA) += kb3886_bl.o > > > obj-$(CONFIG_BACKLIGHT_SKY81452) += sky81452-backlight.o > > > obj-$(CONFIG_BACKLIGHT_TOSA) += tosa_bl.o > > > diff --git a/drivers/video/backlight/rt4831-backlight.c b/drivers/video/backlight/rt4831-backlight.c > > > new file mode 100644 > > > index 00000000..42155c7 > > > --- /dev/null > > > +++ b/drivers/video/backlight/rt4831-backlight.c > > > @@ -0,0 +1,203 @@ > > > +// SPDX-License-Identifier: GPL-2.0-only > > > + > > > +#include <dt-bindings/leds/rt4831-backlight.h> > > > +#include <linux/backlight.h> > > > +#include <linux/bitops.h> > > > +#include <linux/kernel.h> > > > +#include <linux/module.h> > > > +#include <linux/platform_device.h> > > > +#include <linux/property.h> > > > +#include <linux/regmap.h> > > > + > > > +#define RT4831_REG_BLCFG 0x02 > > > +#define RT4831_REG_BLDIML 0x04 > > > +#define RT4831_REG_ENABLE 0x08 > > > + > > > +#define RT4831_BLMAX_BRIGHTNESS 2048 > > > + > > > +#define RT4831_BLOVP_MASK GENMASK(7, 5) > > > +#define RT4831_BLOVP_SHIFT 5 > > > +#define RT4831_BLPWMEN_MASK BIT(0) > > > +#define RT4831_BLEN_MASK BIT(4) > > > +#define RT4831_BLCH_MASK GENMASK(3, 0) > > > +#define RT4831_BLDIML_MASK GENMASK(2, 0) > > > +#define RT4831_BLDIMH_MASK GENMASK(10, 3) > > > +#define RT4831_BLDIMH_SHIFT 3 > > > + > > > +struct rt4831_priv { > > > + struct device *dev; > > > + struct regmap *regmap; > > > + struct backlight_device *bl; > > > +}; > > > + > > > +static int rt4831_bl_update_status(struct backlight_device *bl_dev) > > > +{ > > > + struct rt4831_priv *priv = bl_get_data(bl_dev); > > > + int brightness = backlight_get_brightness(bl_dev); > > > + unsigned int enable = brightness ? RT4831_BLEN_MASK : 0; > > > + u8 v[2]; > > > + int ret; > > > + > > > + if (brightness) { > > > + v[0] = (brightness - 1) & RT4831_BLDIML_MASK; > > > + v[1] = ((brightness - 1) & RT4831_BLDIMH_MASK) >> RT4831_BLDIMH_SHIFT; > > > + > > > + ret = regmap_raw_write(priv->regmap, RT4831_REG_BLDIML, v, sizeof(v)); > > > + if (ret) > > > + return ret; > > > + } > > > + > > > + return regmap_update_bits(priv->regmap, RT4831_REG_ENABLE, RT4831_BLEN_MASK, enable); > > > + > > > +} > > > + > > > +static int rt4831_bl_get_brightness(struct backlight_device *bl_dev) > > > +{ > > > + struct rt4831_priv *priv = bl_get_data(bl_dev); > > > + unsigned int val; > > > + u8 v[2]; > > > + int ret; > > > + > > > + ret = regmap_read(priv->regmap, RT4831_REG_ENABLE, &val); > > > + if (ret) > > > + return ret; > > > + > > > + if (!(val & RT4831_BLEN_MASK)) > > > + return 0; > > > + > > > + ret = regmap_raw_read(priv->regmap, RT4831_REG_BLDIML, v, sizeof(v)); > > > + if (ret) > > > + return ret; > > > + > > > + ret = (v[1] << RT4831_BLDIMH_SHIFT) + (v[0] & RT4831_BLDIML_MASK) + 1; > > > + > > > + return ret; > > > +} > > > + > > > +static const struct backlight_ops rt4831_bl_ops = { > > > + .options = BL_CORE_SUSPENDRESUME, > > > + .update_status = rt4831_bl_update_status, > > > + .get_brightness = rt4831_bl_get_brightness, > > > +}; > > > + > > > +static int rt4831_parse_backlight_properties(struct rt4831_priv *priv, > > > + struct backlight_properties *bl_props) > > > +{ > > > + struct device *dev = priv->dev; > > > + u8 propval; > > > + u32 brightness; > > > + unsigned int val = 0; > > > + int ret; > > > + > > > + /* common properties */ > > > + ret = device_property_read_u32(dev, "max-brightness", &brightness); > > > + if (ret) > > > + brightness = RT4831_BLMAX_BRIGHTNESS; > > > + > > > + bl_props->max_brightness = min_t(u32, brightness, RT4831_BLMAX_BRIGHTNESS); > > > + > > > + ret = device_property_read_u32(dev, "default-brightness", &brightness); > > > + if (ret) > > > + brightness = bl_props->max_brightness; > > > + > > > + bl_props->brightness = min_t(u32, brightness, bl_props->max_brightness); > > > + > > > + /* vendor properties */ > > > + if (device_property_read_bool(dev, "richtek,pwm-enable")) > > > + val = RT4831_BLPWMEN_MASK; > > > + > > > + ret = regmap_update_bits(priv->regmap, RT4831_REG_BLCFG, RT4831_BLPWMEN_MASK, val); > > > + if (ret) > > > + return ret; > > > + > > > + ret = device_property_read_u8(dev, "richtek,bled-ovp-sel", &propval); > > > + if (ret) > > > + propval = RT4831_BLOVPLVL_21V; > > > + > > > + propval = min_t(u8, propval, RT4831_BLOVPLVL_29V); > > > + ret = regmap_update_bits(priv->regmap, RT4831_REG_BLCFG, RT4831_BLOVP_MASK, > > > + propval << RT4831_BLOVP_SHIFT); > > > + if (ret) > > > + return ret; > > > + > > > + ret = device_property_read_u8(dev, "richtek,channel-use", &propval); > > > + if (ret) { > > > + dev_err(dev, "richtek,channel-use DT property missing\n"); > > > + return ret; > > > + } > > > + > > > + if (!(propval & RT4831_BLCH_MASK)) { > > > + dev_err(dev, "No channel specified\n"); > > > + return -EINVAL; > > > + } > > > + > > > + return regmap_update_bits(priv->regmap, RT4831_REG_ENABLE, RT4831_BLCH_MASK, propval); > > > +} > > > + > > > +static int rt4831_bl_probe(struct platform_device *pdev) > > > +{ > > > + struct rt4831_priv *priv; > > > + struct backlight_properties bl_props = { .type = BACKLIGHT_RAW, > > > + .scale = BACKLIGHT_SCALE_LINEAR }; > > > + int ret; > > > + > > > + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); > > > + if (!priv) > > > + return -ENOMEM; > > > + > > > + priv->dev = &pdev->dev; > > > + > > > + priv->regmap = dev_get_regmap(pdev->dev.parent, NULL); > > > + if (!priv->regmap) { > > > + dev_err(&pdev->dev, "Failed to init regmap\n"); > > > + return -ENODEV; > > > + } > > > + > > > + ret = rt4831_parse_backlight_properties(priv, &bl_props); > > > + if (ret) { > > > + dev_err(&pdev->dev, "Failed to parse backlight properties\n"); > > > + return ret; > > > + } > > > + > > > + priv->bl = devm_backlight_device_register(&pdev->dev, pdev->name, &pdev->dev, priv, > > > + &rt4831_bl_ops, &bl_props); > > > + if (IS_ERR(priv->bl)) { > > > + dev_err(&pdev->dev, "Failed to register backlight\n"); > > > + return PTR_ERR(priv->bl); > > > + } > > > + > > > + backlight_update_status(priv->bl); > > > + platform_set_drvdata(pdev, priv); > > > + > > > + return 0; > > > +} > > > + > > > +static int rt4831_bl_remove(struct platform_device *pdev) > > > +{ > > > + struct rt4831_priv *priv = platform_get_drvdata(pdev); > > > + struct backlight_device *bl_dev = priv->bl; > > > + > > > + bl_dev->props.brightness = 0; > > > + backlight_update_status(priv->bl); > > > + > > > + return 0; > > > +} > > > + > > > +static const struct of_device_id __maybe_unused rt4831_bl_of_match[] = { > > > + { .compatible = "richtek,rt4831-backlight", }, > > > + {} > > > +}; > > > +MODULE_DEVICE_TABLE(of, rt4831_bl_of_match); > > > + > > > +static struct platform_driver rt4831_bl_driver = { > > > + .driver = { > > > + .name = "rt4831-backlight", > > > + .of_match_table = rt4831_bl_of_match, > > > + }, > > > + .probe = rt4831_bl_probe, > > > + .remove = rt4831_bl_remove, > > > +}; > > > +module_platform_driver(rt4831_bl_driver); > > > + > > > +MODULE_AUTHOR("ChiYuan Huang <cy_huang@xxxxxxxxxxx>"); > > > +MODULE_LICENSE("GPL v2"); > > > -- > > > 2.7.4 > > >
