Re: [PATCH 1/5] PCI: qcom: add support for IPQ60xx PCIe controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Rob,

Thanks for your review.

I have a few comments below.

On Tue, Apr 20 2021, Rob Herring wrote:
> On Tue, Apr 20, 2021 at 02:21:36PM +0300, Baruch Siach wrote:
>> From: Selvam Sathappan Periakaruppan <speriaka@xxxxxxxxxxxxxx>
>> 
>> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
>> platform.
>> 
>> The code is based on downstream Codeaurora kernel v5.4. Split out the
>> registers access part from .init into .post_init. Registers are only
>> accessible after phy_power_on().
>> 
>> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@xxxxxxxxxxxxxx>
>> Signed-off-by: Baruch Siach <baruch@xxxxxxxxxx>
>> ---
>>  drivers/pci/controller/dwc/pcie-qcom.c | 279 +++++++++++++++++++++++++
>>  1 file changed, 279 insertions(+)
>> 
>> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
>> index 8a7a300163e5..3e27de744738 100644
>> --- a/drivers/pci/controller/dwc/pcie-qcom.c
>> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
>> @@ -41,6 +41,31 @@
>>  #define L23_CLK_RMV_DIS				BIT(2)
>>  #define L1_CLK_RMV_DIS				BIT(1)
>>  
>> +#define PCIE_ATU_CR1_OUTBOUND_6_GEN3		0xC00
>> +#define PCIE_ATU_CR2_OUTBOUND_6_GEN3		0xC04
>> +#define PCIE_ATU_LOWER_BASE_OUTBOUND_6_GEN3	0xC08
>> +#define PCIE_ATU_UPPER_BASE_OUTBOUND_6_GEN3	0xC0C
>> +#define PCIE_ATU_LIMIT_OUTBOUND_6_GEN3		0xC10
>> +#define PCIE_ATU_LOWER_TARGET_OUTBOUND_6_GEN3	0xC14
>> +#define PCIE_ATU_UPPER_TARGET_OUTBOUND_6_GEN3	0xC18
>> +
>> +#define PCIE_ATU_CR1_OUTBOUND_7_GEN3		0xE00
>> +#define PCIE_ATU_CR2_OUTBOUND_7_GEN3		0xE04
>> +#define PCIE_ATU_LOWER_BASE_OUTBOUND_7_GEN3	0xE08
>> +#define PCIE_ATU_UPPER_BASE_OUTBOUND_7_GEN3	0xE0C
>> +#define PCIE_ATU_LIMIT_OUTBOUND_7_GEN3		0xE10
>> +#define PCIE_ATU_LOWER_TARGET_OUTBOUND_7_GEN3	0xE14
>> +#define PCIE_ATU_UPPER_TARGET_OUTBOUND_7_GEN3 	0xE18
>
> ATU registers are standard DWC registers. Plus upstream now dynamically 
> detects how many ATU regions there are.
>
>> +#define PCIE20_COMMAND_STATUS			0x04
>> +#define BUS_MASTER_EN				0x7
>> +#define PCIE20_DEVICE_CONTROL2_STATUS2		0x98
>> +#define PCIE_CAP_CPL_TIMEOUT_DISABLE		0x10
>
> All PCI standard registers.

PCIE20_COMMAND_STATUS is indeed the common PCI_COMMAND. I could not find
anything that matches PCIE20_DEVICE_CONTROL2_STATUS2. Where should I
look?

>
>> +#define PCIE30_GEN3_RELATED_OFF			0x890
>
> Looks like a DWC port logic register. The define at a minimum goes in 
> the common code. We probably already have one. Code touching the 
> register should ideally be there too (hint: look at the other drivers). 

pcie-tegra194.c uses the equivalent GEN3_RELATED_OFF. So I can move the
definition to a common header. As for the code, I don't know. The tegra
configuration sequence involves other registers as well.

[snip]

>> +static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
>> +{
>> +	struct dw_pcie *pci = pcie->pci;
>> +	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
>> +	u32 val;
>> +	int i;
>> +
>> +	writel(SLV_ADDR_SPACE_SZ,
>> +		pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
>> +
>> +	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
>> +	val &= ~BIT(0);
>
> What's BIT(0)?

I have no idea. I have no access to hardware documentation. I'm just
porting working code from the Codeaurora tree.

>
>> +	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
>> +
>> +	writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
>> +
>> +	writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
>> +	writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN,
>> +		pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
>> +	writel(RXEQ_RGRDLESS_RXTS | GEN3_ZRXDC_NONCOMPL,
>> +		pci->dbi_base + PCIE30_GEN3_RELATED_OFF);
>> +
>> +	writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS
>> +		| SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS |
>> +		AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS,
>> +		pcie->parf + PCIE20_PARF_SYS_CTRL);
>> +
>> +	writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
>> +
>> +	writel(BUS_MASTER_EN, pci->dbi_base + PCIE20_COMMAND_STATUS);
>
> Pretty sure the DWC core or PCI core does this already.
>
>> +
>> +	writel(DBI_RO_WR_EN, pci->dbi_base + PCIE20_MISC_CONTROL_1_REG);
>> +	writel(PCIE_CAP_LINK1_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
>> +
>> +	/* Configure PCIe link capabilities for ASPM */
>> +	val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
>> +	val &= ~PCI_EXP_LNKCAP_ASPMS;
>> +	writel(val, pci->dbi_base + offset + PCI_EXP_LNKCAP);
>> +
>> +	writel(PCIE_CAP_CPL_TIMEOUT_DISABLE, pci->dbi_base +
>> +		PCIE20_DEVICE_CONTROL2_STATUS2);
>> +
>> +	writel(PCIE_CAP_CURR_DEEMPHASIS | SPEED_GEN3,
>> +			pci->dbi_base + offset + PCI_EXP_DEVCTL2);
>
> This all looks like stuff that should be in the DWC core code. Maybe we 
> need an ASPM disable quirk or something? That's probably somewhat 
> common.

Where in common code should that be? Which part is quirky?

>> +
>> +	for (i = 0;i < 256;i++)
>> +		writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N
>> +				+ (4 * i));
>> +
>
>> +	writel(0x4, pci->atu_base + PCIE_ATU_CR1_OUTBOUND_6_GEN3);
>> +	writel(0x90000000, pci->atu_base + PCIE_ATU_CR2_OUTBOUND_6_GEN3);
>> +	writel(0x0, pci->atu_base + PCIE_ATU_LOWER_BASE_OUTBOUND_6_GEN3);
>> +	writel(0x0, pci->atu_base + PCIE_ATU_UPPER_BASE_OUTBOUND_6_GEN3);
>> +	writel(0x00107FFFF, pci->atu_base + PCIE_ATU_LIMIT_OUTBOUND_6_GEN3);
>> +	writel(0x0, pci->atu_base + PCIE_ATU_LOWER_TARGET_OUTBOUND_6_GEN3);
>> +	writel(0x0, pci->atu_base + PCIE_ATU_UPPER_TARGET_OUTBOUND_6_GEN3);
>> +	writel(0x5, pci->atu_base + PCIE_ATU_CR1_OUTBOUND_7_GEN3);
>> +	writel(0x90000000, pci->atu_base + PCIE_ATU_CR2_OUTBOUND_7_GEN3);
>> +	writel(0x200000, pci->atu_base + PCIE_ATU_LOWER_BASE_OUTBOUND_7_GEN3);
>> +	writel(0x0, pci->atu_base + PCIE_ATU_UPPER_BASE_OUTBOUND_7_GEN3);
>> +	writel(0x7FFFFF, pci->atu_base + PCIE_ATU_LIMIT_OUTBOUND_7_GEN3);
>> +	writel(0x0, pci->atu_base + PCIE_ATU_LOWER_TARGET_OUTBOUND_7_GEN3);
>> +	writel(0x0, pci->atu_base + PCIE_ATU_UPPER_TARGET_OUTBOUND_7_GEN3);
>
> This should all be coming from 'ranges' in the DT. If not, why not?

I'll try to drop it and see if it works. I see that common code
overwrites this area anyway.

>
> If you haven't caught the theme yet, everything outside of PARF register 
> accesses had better have a good explanation why they can't be in common 
> code.
>
>> +
>> +	return 0;
>> +}
>> +
>>  static int qcom_pcie_link_up(struct dw_pcie *pci)
>>  {
>>  	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
>> @@ -1456,6 +1720,15 @@ static const struct qcom_pcie_ops ops_1_9_0 = {
>>  	.config_sid = qcom_pcie_config_sid_sm8250,
>>  };
>>  
>> +/* Qcom IP rev.: 2.9.0  Synopsys IP rev.: 5.00a */
>> +static const struct qcom_pcie_ops ops_2_9_0 = {
>> +	.get_resources = qcom_pcie_get_resources_2_9_0,
>> +	.init = qcom_pcie_init_2_9_0,
>> +	.post_init = qcom_pcie_post_init_2_9_0,
>> +	.deinit = qcom_pcie_deinit_2_9_0,
>> +	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
>> +};
>> +
>>  static const struct dw_pcie_ops dw_pcie_ops = {
>>  	.link_up = qcom_pcie_link_up,
>>  	.start_link = qcom_pcie_start_link,
>> @@ -1508,6 +1781,11 @@ static int qcom_pcie_probe(struct platform_device *pdev)
>>  		goto err_pm_runtime_put;
>>  	}
>>  
>> +	/* We need ATU for .post_init */
>> +	pci->atu_base = devm_platform_ioremap_resource_byname(pdev, "atu");
>
> The DWC core handles this now.

With ATU code in .post_init gone, we can remove this as well.

baruch

-- 
                                                     ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch@xxxxxxxxxx - tel: +972.52.368.4656, http://www.tkos.co.il -



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux