Hi Andrew, On Fri, 2021-04-09 at 22:10 +0200, Andrew Lunn wrote: > On Fri, Apr 09, 2021 at 07:42:32AM +0200, Sander Vanheule wrote: > > Hi Andrew, > > > > Thank you for the feedback. You can find a (leaked) datasheet at: > > https://github.com/libc0607/Realtek_switch_hacking/blob/files/RTL8231_Datasheet_1.2.pdf > > So this is not really an MFD. It has different ways of making use of > pins, which could be used for GPIO, but can also be used for LEDs. You > could look if it better fits in drivers/leds. But you can also use > GPIO drivers for LEDs via led-gpio. The chip provides LED scanning matrix functionality, for which one needs to set up row and column pins. The chip supports 3×12 + 3×12 + 2×8 (88) LEDs; a lot more than it has pins available. There is also (limited) support for hardware-accelerated blinking. For example, single LED color scan matrix ("group A" for ports 0-11) would be wired up as follows: Row and column pins of scan matrix for LED0, LED1, LED2 Columns control LED0/1/2 for ports [n] and [n+6] L0[n] L1[n] L2[n] L0[n+6] L1[n+6] L2[n+6] | | | | | | P0/P6 --X--------X--------X--------X--------X--------X (3) | | | | | | P1/P7 --X--------X--------X--------X--------X--------X (4) | | | | | | P2/P8 --X--------X--------X--------X--------X--------X (5) | | | | | | P3/P9 --X--------X--------X--------X--------X--------X (6) | | | | | | P4/P10 --X--------X--------X--------X--------X--------X (7) | | | | | | P5/P11 --X--------X--------X--------X--------X--------X (8) (0) (1) (2) (9) (10) (11) So far, I haven't seen any actual hardware implementation that uses the scanning matrix functionality (or the buzzer control feature with frequency selection). 1:1 use of GPIO pins for LEDs is indeed trivial with led-gpio, and I am currently using this on one of my devices. > > > I don't understand this split. Why not > > > > > > mdio-bus { > > > compatible = "vendor,mdio"; > > > ... > > > > > > expander0: expander@0 { > > > /* > > > * Provide compatible for working registration of mdio > > > device. > > > * Device probing happens in gpio1 node. > > > */ > > > compatible = "realtek,rtl8231-expander"; > > > reg = <0>; > > > gpio-controller; > > > }; > > > }; > > > > > > You can list whatever properties you need in the node. Ethernet > > > switches have interrupt-controller, embedded MDIO busses with PHYs on > > > them etc. > > > > This is what I tried initially, but it doesn't seem to work. The node > > is probably still added as an MDIO device, but rtl8231_gpio_probe() > > doesn't appear to get called at all. I do agree it would be preferable > > over the split specification. > > Look at drivers/net/dsa/mv88e6xxx/chip.c for how to register an mdio > driver. If you still cannot get it to work, post your code and i will > take a look. Thanks for the suggestion. I've managed to create a cleaner mdio_device driver with a single corresponding DT node. Would the following make sense for a more complete DT description? Or would I need sub-nodes to group e.g. the pin control or LED nodes/properties? expander@31 { /* Either "realtek,rtl8231-mdio" or "realtek,rtl8231-smi" */ compatible = "realtek,rtl8231-mdio"; reg = <31>; /* Must be <1> (8 bit) or <2> (16 bit); only for "realtek,rtl8231-smi" */ realtek,smi-regnum-width = <1>; /** GPIO controller properties **/ gpio-controller; #gpio-cells = <2>; ngpios = <37>; poe_enable { gpio-hog; gpios = <10 0>; output-high; }; /** Pin controller properties **/ /* Can only set a global drive strength, 4mA or 8mA */ realtek,gpio-drive-strength = <4>; /* Global LED scan matrix setting, 0 (single-color) or 1 (bi-color) */ realtek,led-color-scan-mode = <0>; pinctrl-names = "default"; pinctrl-0 = <&user_button>, <&port_leds>; user_button : user_button_cfg { pins = "gpio31"; function = "gpio"; /* Only GPIOs 31-35 can do hardware debouncing */ /* Debouncing is either disabled or 100ms */ input-debounce = <100000>; }; port_leds : port_leds_cfg { /* Select two columns (LED colors) for switch ports 0-7 */ pins = "gpio0", "gpio1", "gpio9", "gpio10", "gpio3", "gpio4", "gpio5", "gpio6"; function = "led"; }; /** LED config **/ #address-cells = <2>; #size-cells = <0>; led@0.0 { /* LED0 for port 0, corresponds to bits [2:0] in regnum 0x09 */ reg = <0 0>; ... }; led@0.1 { /* LED1 for port 0 */ reg = <0 1>; ... }; /* LEDs 1.x, 2.x, 3.x, 6.x, 7.x, 8.x, 9.x omitted */ }; As a final remark, I have found out that this chip doesn't actually talk I2C, but rather Realtek's proprietary SMI. These two protocols are very similar w.r.t. to byte framing, but SMI requires the bus master to write the register number byte(s) on both READ and WRITE frames. I2C/SMBUS does a WRITE for the register number first, then a separate READ for the register value. This means I can't get regmap_i2c to work. There is an existing, bit-banged implementation of this SMI protocol (see "realtek,smi-mdio", realtek- smi.c). If I could re-use this in some way, there would only need to be an MDIO implementation. However, we have noticed that the larger phy address space (7-bit in SMI vs. 5-bit in MDIO) did require a patch to make it work on ethernet switches with more than 32 ports (and corresponding phys) on a single SMI bus. Best, Sander
