Hi all, On 16/04/21 10:56 am, Aswath Govindraju wrote: > The following series of patches add support for CAN transceivers. > > TCAN1042 has a standby signal that needs to be pulled high for > sending/receiving messages[1]. TCAN1043 has a enable signal along with > standby signal that needs to be pulled up for sending/receiving > messages[2], and other combinations of the two lines can be used to put the > transceiver in different states to reduce power consumption. On boards > like the AM654-idk and J721e-evm these signals are controlled using gpios. > > Patch 1 rewords the comment that restricts max_link_rate attribute to have > units of Mbps. > > Patch 2 models the transceiver as a phy device tree node with properties > for max bit rate supported, gpio properties for indicating gpio pin numbers > to which standby and enable signals are connected. > > Patch 2 adds a generic driver to support CAN transceivers. > > changes since v3: > - dropped patch 2(in v3) > - changed the node name property in patch 3(in v3) > - picked up Rob Herring's reviewed-by for patch 3(in v3) > > changes since v2: > - dropped 5 and 6 patches and to be sent via linux-can-next > - added static keyword for can_transceiver_phy_probe() > - changed enable gpio example to active high in patch 3 > - Rearranged the file names in alphabetical order in Makefile > and MAINTAINERS file > > changes since v1: > - Added patch 1 (in v2) that rewords the comment that restrict > max_link_rate attribute to have units of Mbps. > - Added patch 2 (in v2) that adds an API for > devm_of_phy_optional_get_by_index > - Patch 1 (in v1) > - updated MAINTAINERS file > - Patch 2 (in v1) > - replaced m_can with CAN to make the driver independent of CAN driver > - Added prefix CAN_TRANSCEIVER for EN_PRESENT and STB_PRESENT > - Added new line before return statements in power_on() and power_off > - Added error handling patch for devm_kzalloc() > - used the max_link_rate attribute directly instead of dividing it by > 1000000 > - removed the spaces before GPIOD_OUT_LOW in devm_gpiod_get() > - Corrected requested value for standby-gpios to GPIOD_OUT_HIGH > - Updated MAINTAINERS file > - Patch 3 (in v1) > - replaced minItems with maxItems > - Removed phy-names property as there is only one phy > - Patch 4 (in v1) > - replaced dev_warn with dev_info when no transceiver is found > - Added struct phy * field in m_can_classdev struct > - moved phy_power_on and phy_power_off to m_can_open and m_can_close > respectively > - Moved the check for max_bit_rate to generice transceiver driver > > [1] - https://www.ti.com/lit/ds/symlink/tcan1042h.pdf > [2] - https://www.ti.com/lit/ds/symlink/tcan1043-q1.pdf > > Posted v5 for this series. Thanks, Aswath > Aswath Govindraju (3): > phy: core: Reword the comment specifying the units of max_link_rate to > be Mbps > dt-bindings: phy: Add binding for TI TCAN104x CAN transceivers > phy: phy-can-transceiver: Add support for generic CAN transceiver > driver > > .../bindings/phy/ti,tcan104x-can.yaml | 56 +++++++ > MAINTAINERS | 2 + > drivers/phy/Kconfig | 9 ++ > drivers/phy/Makefile | 1 + > drivers/phy/phy-can-transceiver.c | 146 ++++++++++++++++++ > include/linux/phy/phy.h | 2 +- > 6 files changed, 215 insertions(+), 1 deletion(-) > create mode 100644 Documentation/devicetree/bindings/phy/ti,tcan104x-can.yaml > create mode 100644 drivers/phy/phy-can-transceiver.c >
