Like most clock drivers, the Maxim 77686 PMIC clock binding
follows the convention that the "#clock-cells" property is
used to specify the number of cells in a clock provider.
But the binding document is not clear enough that it shall
be set to 1 since the PMIC support multiple clocks outputs.
Also, explain that the clocks identifiers are defined in a
header file that can be included by Device Tree source with
client nodes to avoid using magic numbers.
Finally, add "clock-output-names" as an optional property
since now is supported by the clock driver.
Signed-off-by: Javier Martinez Canillas <javier.martinez@xxxxxxxxxxxxxxx>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>
Reviewed-by: Doug Anderson <dianders@xxxxxxxxxxxx>
Reviewed-by: Mike Turquette <mturquette@xxxxxxxxxx>
---
Changes since v6: None
Changes since v5:
- Fix generic driver changes merged into max77802 clock patch by mistake.
Suggested by Yadwinder Singh Brar.
- Register clock lookups using clk_register_clkdev() instead of doing manually.
- Use the managed devm_clk_register() function and remove clk un-registration.
- Add "clock-output-names" property support. Suggested by Yadwinder Singh Brar.
- Return the rate unconditionally in recalc_rate. Suggested by Mike Turquette.
Changes since v4: None
Changes since v3:
- Don't change clock-names property to make clear that it's
the consumer clock name and should not match the producer clock.
Suggested by Doug Anderson.
---
.../devicetree/bindings/clock/maxim,max77686.txt | 16 ++++++++++++----
1 file changed, 12 insertions(+), 4 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/maxim,max77686.txt b/Documentation/devicetree/bindings/clock/maxim,max77686.txt
index 96ce71b..9c40739 100644
--- a/Documentation/devicetree/bindings/clock/maxim,max77686.txt
+++ b/Documentation/devicetree/bindings/clock/maxim,max77686.txt
@@ -9,13 +9,21 @@ The MAX77686 contains three 32.768khz clock outputs that can be controlled
Following properties should be presend in main device node of the MFD chip.
Required properties:
-- #clock-cells: simple one-cell clock specifier format is used, where the
- only cell is used as an index of the clock inside the provider. Following
- indices are allowed:
+
+- #clock-cells: from common clock binding; shall be set to 1.
+
+Optional properties:
+- clock-output-names: From common clock binding.
+
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume. Following indices are allowed:
- 0: 32khz_ap clock,
- 1: 32khz_cp clock,
- 2: 32khz_pmic clock.
+Clocks are defined as preprocessor macros in dt-bindings/clock/maxim,max77686.h
+header and can be used in device tree sources.
+
Example: Node of the MFD chip
max77686: max77686@09 {
@@ -34,5 +42,5 @@ Example: Clock consumer node
compatible = "bar,foo";
/* ... */
clock-names = "my-clock";
- clocks = <&max77686 2>;
+ clocks = <&max77686 MAX77686_CLK_PMIC>;
};
--
2.0.0.rc2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
