On 07/14/2014 08:54 AM, Dong Aisheng wrote:
On Fri, Jul 11, 2014 at 04:11:03PM +0530, Varka Bhadram wrote:
On 07/11/2014 03:59 PM, Dong Aisheng wrote:
add M_CAN device tree binding documentation
Cc: Wolfgang Grandegger <wg@xxxxxxxxxxxxxx>
Cc: Marc Kleine-Budde <mkl@xxxxxxxxxxxxxx>
Cc: Mark Rutland <mark.rutland@xxxxxxx>
Cc: Oliver Hartkopp <socketcan@xxxxxxxxxxxx>
Cc: Varka Bhadram <varkabhadram@xxxxxxxxx>
Signed-off-by: Dong Aisheng <b29396@xxxxxxxxxxxxx>
---
.../devicetree/bindings/net/can/m_can.txt | 65 ++++++++++++++++++++
1 files changed, 65 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/net/can/m_can.txt
diff --git a/Documentation/devicetree/bindings/net/can/m_can.txt b/Documentation/devicetree/bindings/net/can/m_can.txt
new file mode 100644
index 0000000..c4cb263
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/m_can.txt
@@ -0,0 +1,65 @@
+Bosch MCAN controller Device Tree Bindings
+-------------------------------------------------
+
+Required properties:
+- compatible : Should be "bosch,m_can" for M_CAN controllers
+- reg : physical base address and size of the M_CAN
+ registers map and Message RAM
+- reg-names : Should be "m_can" and "message_ram"
+- interrupts : Should be the interrupt number of M_CAN interrupt
+ line 0 and line 1, could be same if sharing
+ the same interrupt.
+- interrupt-names : Should contain "int0" and "int1"
+- clocks : Clocks used by controller, should be host clock
+ and CAN clock.
+- clock-names : Should contain "hclk" and "cclk"
+- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt
I think this should be pinctrl-0
First, this part is defined by pinctrl binding doc.
Second i think it may be possible someone wants to add other pinctrl states
when implement low power state in the future.
So i just keep it as pinctrl-<n>.
Normally we will use pinctrl-0 for mentioning the pinctrl bindings.
If somebody going to add something to the pinctrl bindings they will
add separately with pinctrl-1: bla bla bla...
+- pinctrl-names : Names corresponding to the numbered pinctrl states
remove 1 tab space before :
It's a bit strange.
Other line like pinctrl-<n> is also two tabs.
And the code looks fine and already aligned.
- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt
- pinctrl-names : Names corresponding to the numbered pinctrl states
Do you mean change line of pinctrl-names from two tabs to one space and a tab before :?
When i see in the patch the alignment is like this
pinctrl-<n> :
pinctrl-name :
+- mram-cfg : Message RAM configuration data.
+ Multiple M_CAN instances can share the same Message RAM and each element(e.g
+ Rx FIFO or Tx Buffer and etc) number in Message RAM is also configurable,
+ so this property is telling driver how the shared or private Message RAM
+ are used by this M_CAN controller.
+
It may written like:
mram-cfg : Message RAM configuration data
Multiple M_CAN instances can share the same Message RAM and each element
(e.g Rx FIFO or Tx Buffer and etc) number in Message RAM is also configurable,
...
I'm fine with that.
The question is it's easy to over 80 columns if writing like that,
is it ok?
When we follow the above format it would be more readable.
Regards
Dong Aisheng
--
Regards,
Varka Bhadram.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
