Re: [PATCH V2 1/5] arm64: dts: qcom: pm7325: Add PMIC peripherals for pm7325

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2021-04-03 02:05, Matthias Kaehlcke wrote:
On Fri, Apr 02, 2021 at 10:35:54AM -0700, Matthias Kaehlcke wrote:
On Thu, Apr 01, 2021 at 02:43:12PM +0530, satya priya wrote:

> subject: arm64: dts: qcom: pm7325: Add PMIC peripherals for pm7325

nit: maybe just 'arm64: dts: qcom: Add pm7325 support/.dtsi' or similar?

> Add temp-alarm and GPIO support for pm7325.

nit: it's more than that, you are adding the .dtsi for the PMIC itself.

> Signed-off-by: satya priya <skakit@xxxxxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/pm7325.dtsi | 53 ++++++++++++++++++++++++++++++++++++
>  1 file changed, 53 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/pm7325.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/pm7325.dtsi b/arch/arm64/boot/dts/qcom/pm7325.dtsi
> new file mode 100644
> index 0000000..1e0848a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pm7325.dtsi
> @@ -0,0 +1,53 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +// Copyright (c) 2021, The Linux Foundation. All rights reserved.
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +&spmi_bus {
> +	pm7325: pmic@1 {
> +		compatible = "qcom,pm7325", "qcom,spmi-pmic";

I saw the patches that add the compatible strings for the GPIOs, but
can't find those that add the strings for the PMICs themselves. Could
you provide a link if they have been sent already?

> +		reg = <0x1 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pm7325_temp_alarm: temp-alarm@a00 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0xa00>;
> +			interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
> +
> +		pm7325_gpios: gpios@8800 {
> +			compatible = "qcom,pm7325-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pm7325_gpios 0 0 10>;

The GPIO enumeration is a bit confusing. The pm7325 has GPIO_01 to
GPIO_10, however IIUC they are mapped such that under Linux
enumeration starts with 0. I guess it makes sense to start with 0 and
it's done consistently for 'qcom,spmi-gpio', but it's something that must
be taken into account when using/configuring those GPIOs.

Sure, will take care of this while configuring the GPIOs.



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux