On 2021-03-23 12:31, Stephen Boyd wrote:
Quoting Shaik Sajida Bhanu (2021-03-20 11:17:00)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 54d2cb3..4105263 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -8,6 +8,7 @@
/dts-v1/;
#include "sc7280.dtsi"
+#include <dt-bindings/gpio/gpio.h>
Please include this before sc7280.dtsi
Sure
/ {
model = "Qualcomm Technologies, Inc. sc7280 IDP platform";
@@ -242,6 +243,30 @@
status = "okay";
};
+&sdhc_1 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_on>;
+ pinctrl-1 = <&sdc1_off>;
+
+ vmmc-supply = <&vreg_l7b_2p9>;
+ vqmmc-supply = <&vreg_l19b_1p8>;
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ pinctrl-names = "default","sleep";
Please add a space after the comma ^
Sure
+ pinctrl-0 = <&sdc2_on>;
+ pinctrl-1 = <&sdc2_off>;
+
+ vmmc-supply = <&vreg_l9c_2p9>;
+ vqmmc-supply = <&vreg_l6c_2p9>;
+
+ cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
+};
+
/* PINCTRL - additions to nodes defined in sc7280.dtsi */
&qup_uart5_default {
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi
b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 8f6b569..69eb064 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -20,6 +20,11 @@
chosen { };
+ aliases {
+ mmc1 = &sdhc_1;
+ mmc2 = &sdhc_2;
+ };
+
clocks {
xo_board: xo-board {
compatible = "fixed-clock";
@@ -305,6 +310,64 @@
#power-domain-cells = <1>;
};
+ sdhc_1: sdhci@7c4000 {
+ compatible = "qcom,sdhci-msm-v5";
+ reg = <0 0x7c4000 0 0x1000>,
Please add leading zeroes to the physical address, i.e. 0x007c4000
Sure
+ <0 0x7c5000 0 0x1000>;
+ reg-names = "hc", "cqhci";
+
+ iommus = <&apps_smmu 0xC0 0x0>;
Lowercase hex please.
Sure
+ interrupts = <GIC_SPI 652
IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 656
IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC1_APPS_CLK>,
+ <&gcc GCC_SDCC1_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "core", "iface", "xo";
+ interconnects = <&aggre1_noc MASTER_SDCC_1 0
&mc_virt SLAVE_EBI1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0
&cnoc2 SLAVE_SDCC_1 0>;
+ interconnect-names = "sdhc-ddr","cpu-sdhc";
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&sdhc1_opp_table>;
+
+ bus-width = <8>;
+ non-removable;
+ supports-cqe;
+ no-sd;
+ no-sdio;
+
+ max-frequency = <192000000>;
Is this necessary?
yes, to avoid lower speed modes running with high clock rates.
+
+ qcom,dll-config = <0x0007642c>;
+ qcom,ddr-config = <0x80040868>;
+
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+
+ status = "disabled";
Can this be near the compatible string?
Sure
+
+ sdhc1_opp_table: sdhc1-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-100000000 {
+ opp-hz = /bits/ 64
<100000000>;
+ required-opps =
<&rpmhpd_opp_low_svs>;
+ opp-peak-kBps = <1200000
76000>;
+ opp-avg-kBps = <1200000
50000>;
+ };
+
+ opp-384000000 {
+ opp-hz = /bits/ 64
<384000000>;
+ required-opps =
<&rpmhpd_opp_nom>;
+ opp-peak-kBps = <5400000
1600000>;
+ opp-avg-kBps = <6000000
300000>;
+ };
+ };
+ };
+
qupv3_id_0: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x009c0000 0 0x2000>;
@@ -328,6 +391,54 @@
};
};
+ sdhc_2: sdhci@8804000 {
+ compatible = "qcom,sdhci-msm-v5";
+ reg = <0 0x08804000 0 0x1000>;
This has leading zeroes, great!
+
+ iommus = <&apps_smmu 0x100 0x0>;
+ interrupts = <GIC_SPI 207
IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 223
IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC2_APPS_CLK>,
+ <&gcc GCC_SDCC2_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
Is this aligned properly?
yes
+ clock-names = "core", "iface", "xo";
+ interconnects = <&aggre1_noc MASTER_SDCC_2 0
&mc_virt SLAVE_EBI1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0
&cnoc2 SLAVE_SDCC_2 0>;
+ interconnect-names = "sdhc-ddr","cpu-sdhc";
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&sdhc2_opp_table>;
+
+ bus-width = <4>;
+
+ no-mmc;
+ no-sdio;
+
+ max-frequency = <202000000>;
Is this necessary?
yes, to avoid clock running more than required clock rate.
+
+ qcom,dll-config = <0x0007642c>;
+
+ status = "disabled";
Move up near compatible?
sure
+
+ sdhc2_opp_table: sdhc2-opp-table {
+ compatible =
"operating-points-v2";
+
+ opp-100000000 {
+ opp-hz =/bits/ 64
<100000000>;
+ required-opps =
<&rpmhpd_opp_low_svs>;
+ opp-peak-kBps =
<1200000 76000>;
+ opp-avg-kBps =
<1200000 50000>;
+ };
+ opp-202000000 {
+ opp-hz = /bits/ 64
<202000000>;
+ required-opps =
<&rpmhpd_opp_nom>;
+ opp-peak-kBps =
<3500000 1200000>;
+ opp-avg-kBps =
<5000000 100000>;
+ };
+ };
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,sc7280-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>;
