Hi Nishanth, On 22/03/21 9:05 pm, Nishanth Menon wrote: > On 18:42-20210322, Aswath Govindraju wrote: >> The following speed modes are now supported in J7200 SoC, >> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1]. >> - UHS-I speed modes in MMCSD1 subsystem [1]. >> >> Add support for UHS-I modes by adding voltage regulator device tree nodes >> and corresponding pinmux details, to power cycle and voltage switch cards. >> Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1 >> device tree nodes. >> >> Also update the delay values for various speed modes supported, based on >> the revised january 2021 J7200 datasheet[2]. >> >> [1] - section 12.3.6.1.1 MMCSD Features, in >> https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf, >> (SPRUIU1A – JULY 2020 – REVISED JANUARY 2021) >> >> [2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf, >> (SPRSP57B – APRIL 2020 – REVISED JANUARY 2021) >> >> Signed-off-by: Aswath Govindraju <a-govindraju@xxxxxx> >> --- >> .../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++ >> arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++- >> 2 files changed, 54 insertions(+), 2 deletions(-) >> >> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts >> index b493f939b09a..de8c06bdc825 100644 >> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts >> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts >> @@ -16,6 +16,29 @@ >> stdout-path = "serial2:115200n8"; >> bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; >> }; >> + >> + vdd_mmc1: fixedregulator-sd { >> + compatible = "regulator-fixed"; >> + regulator-name = "vdd_mmc1"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-boot-on; >> + enable-active-high; >> + gpios = <&exp2 2 GPIO_ACTIVE_HIGH>; > > is that gpio ? Yes, that is correct. I'll correct it in the respin > I'd encourage to use vin-supply as well. Will add this in respin. > >> + }; >> + >> + vdd_sd_dv: gpio-regulator-vdd-sd-dv { > What does this drive? TLV71033 ? Yes, this node models the TLV71033 voltage regulator that switches the MMC IO signal voltage level between 3.3V and 1.8V. >> + compatible = "regulator-gpio"; >> + regulator-name = "vdd_sd_dv"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&vdd_sd_dv_pins_default>; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-boot-on; > > normally, I'd encourage to use vin-supply as well. Will add this in the respin > >> + gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>; >> + states = <1800000 0x0 >> + 3300000 0x1>; > states = <1800000 0x0>, > <3300000 0x1>; > Will make this change in the respin. > Can you look at j721e as reference? > Will make changes accordingly. >> + }; >> }; >> > > Kishon, > can you look closer at this series? > I'll wait for kishon's feedback and then post respin of this series. Thank you for the review. Regards, Aswath
