Add device trees for OnePlus 5 (cheeseburger) and 5T (dumpling)
MSM8998 SoC smartphones with initial support included for:
- UFS internal storage
- USB peripheral mode
- Display
- Touch
- Bluetooth
- Hall effect sensor
- Power and volume buttons
- Capacitive keypad button backlight (on cheeseburger)
Signed-off-by: Jami Kettunen <jamipkettunen@xxxxxxxxx>
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/Makefile | 2 +
.../dts/qcom/msm8998-oneplus-cheeseburger.dts | 42 ++
.../boot/dts/qcom/msm8998-oneplus-common.dtsi | 519 ++++++++++++++++++
.../dts/qcom/msm8998-oneplus-dumpling.dts | 25 +
4 files changed, 588 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 549a7a2151d4..1beb73f564f7 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -27,6 +27,8 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-asus-novago-tp370ql.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-hp-envy-x2.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-lenovo-miix-630.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-cheeseburger.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts b/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts
new file mode 100644
index 000000000000..13b6b8ad4679
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * OnePlus 5 (cheeseburger) device tree
+ *
+ * Copyright (c) 2021, Jami Kettunen <jamipkettunen@xxxxxxxxx>
+ */
+
+#include <dt-bindings/leds/common.h>
+#include "msm8998-oneplus-common.dtsi"
+
+/ {
+ model = "OnePlus 5";
+ compatible = "oneplus,cheeseburger", "qcom,msm8998";
+ /* Required for bootloader to select correct board */
+ qcom,board-id = <8 0 16859 23>;
+
+ /* Capacitive keypad button backlight */
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&button_backlight_default>;
+
+ button-backlight {
+ gpios = <&pmi8998_gpio 5 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_KBD_BACKLIGHT;
+ default-state = "off";
+ };
+ };
+};
+
+&pmi8998_gpio {
+ button_backlight_default: button-backlight-default {
+ pinconf {
+ pins = "gpio5";
+ function = "normal";
+ bias-pull-down;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
new file mode 100644
index 000000000000..1de4d19ed143
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
@@ -0,0 +1,519 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * OnePlus 5(T) (cheeseburger / dumpling) common device tree source based on msm8998-mtp.dtsi
+ *
+ * Copyright (c) 2021, Jami Kettunen <jamipkettunen@xxxxxxxxx>
+ * Copyright (c) 2016, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "msm8998.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+#include "pm8005.dtsi"
+
+/ {
+ /* Required for bootloader to select correct board */
+ qcom,msm-id = <292 0x20001>; /* 8998 v2.1 */
+
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* Use display framebuffer setup by the UEFI XBL bootloader for simplefb */
+ framebuffer0: framebuffer@9d400000 {
+ compatible = "simple-framebuffer";
+ reg = <0x0 0x9d400000 0x0 0x2400000>;
+ width = <1080>;
+ height = <1920>;
+ stride = <(1080 * 4)>;
+ format = "a8r8g8b8";
+ };
+ };
+
+ reserved-memory {
+ /* Bootloader display framebuffer region */
+ cont_splash_mem: memory@9d400000 {
+ reg = <0x0 0x9d400000 0x0 0x2400000>;
+ no-map;
+ };
+
+ /* For getting crash logs using Android downstream kernels */
+ ramoops@ac000000 {
+ compatible = "ramoops";
+ reg = <0x0 0xac000000 0x0 0x200000>;
+ console-size = <0x80000>;
+ pmsg-size = <0x40000>;
+ record-size = <0x8000>;
+ ftrace-size = <0x20000>;
+ };
+
+ /*
+ * The following memory regions on downstream are "dynamically allocated"
+ * but given the same addresses every time. Hard code them as these addresses
+ * are where the OnePlus signed firmware expects them to be.
+ */
+ ipa_fws_region: ipa@f6800000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0xf6800000 0x0 0x5000>;
+ no-map;
+ };
+ zap_shader_region: gpu@f6900000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0xf6900000 0x0 0x2000>;
+ no-map;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ label = "Volume buttons";
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&vol_keys_default>;
+
+ vol-down {
+ label = "Volume down";
+ gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ debounce-interval = <15>;
+ wakeup-source;
+ };
+
+ vol-up {
+ label = "Volume up";
+ gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ debounce-interval = <15>;
+ wakeup-source;
+ };
+ };
+
+ gpio-hall-sensor {
+ compatible = "gpio-keys";
+ label = "Hall effect sensor";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&hall_sensor_default>;
+
+ hall-sensor {
+ label = "Hall Effect Sensor";
+ gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+/*
+ * OnePlus' ADSP firmware requires 30 MiB in total, so increase the adsp_mem
+ * region by 4 MiB to account for this while relocating the other now
+ * conflicting memory nodes accordingly.
+ */
+&adsp_mem {
+ reg = <0x0 0x8b200000 0x0 0x1e00000>;
+};
+&mpss_mem {
+ reg = <0x0 0x8d000000 0x0 0x7000000>;
+};
+&venus_mem {
+ reg = <0x0 0x94000000 0x0 0x500000>;
+};
+&mba_mem {
+ reg = <0x0 0x94500000 0x0 0x200000>;
+};
+&slpi_mem {
+ reg = <0x0 0x94700000 0x0 0xf00000>;
+};
+&ipa_fw_mem {
+ reg = <0x0 0x95600000 0x0 0x10000>;
+};
+&ipa_gsi_mem {
+ reg = <0x0 0x95610000 0x0 0x5000>;
+};
+&gpu_mem {
+ reg = <0x0 0x95615000 0x0 0x100000>;
+};
+&wlan_msa_mem {
+ reg = <0x0 0x95715000 0x0 0x100000>;
+};
+
+&blsp1_i2c5 {
+ status = "okay";
+
+ touchscreen@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_int_active &ts_reset_active>;
+
+ vdd-supply = <&vreg_l28_3p0>;
+ vio-supply = <&vreg_l6a_1p8>;
+
+ syna,reset-delay-ms = <20>;
+ syna,startup-delay-ms = <20>;
+
+ rmi4-f01@1 {
+ reg = <0x01>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4_f12: rmi4-f12@12 {
+ reg = <0x12>;
+ syna,rezero-wait-ms = <20>;
+ syna,sensor-type = <1>;
+ touchscreen-x-mm = <68>;
+ touchscreen-y-mm = <122>;
+ };
+ };
+};
+
+&blsp1_uart3 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3990-bt";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l17a_1p3>;
+ vddch0-supply = <&vreg_l25a_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&blsp1_uart3_on {
+ rx {
+ /delete-property/ bias-disable;
+ /*
+ * Configure a pull-up on 46 (RX). This is needed to
+ * avoid garbage data when the TX pin of the Bluetooth
+ * module is in tri-state (module powered off or not
+ * driving the signal yet).
+ */
+ bias-pull-up;
+ };
+
+ cts {
+ /delete-property/ bias-disable;
+ /*
+ * Configure a pull-down on 47 (CTS) to match the pull
+ * of the Bluetooth module.
+ */
+ bias-pull-down;
+ };
+};
+
+&blsp2_uart1 {
+ status = "okay";
+};
+
+&pm8005_lsid1 {
+ pm8005-regulators {
+ compatible = "qcom,pm8005-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+
+ pm8005_s1: s1 { /* VDD_GFX supply */
+ regulator-min-microvolt = <524000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-enable-ramp-delay = <500>;
+
+ /* hack until we rig up the gpu consumer */
+ regulator-always-on;
+ };
+ };
+};
+
+&pm8998_gpio {
+ vol_keys_default: vol-keys-default {
+ pinconf {
+ pins = "gpio5", "gpio6";
+ function = "normal";
+ bias-pull-up;
+ input-enable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+ };
+};
+
+&qusb2phy {
+ status = "okay";
+
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+/* Disable all remoteprocs for now until RPM XO clock is usable */
+&remoteproc_mss {
+ status = "disabled";
+};
+
+&rpm_requests {
+ pm8998-regulators {
+ compatible = "qcom,rpm-pm8998-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+ vdd_s2-supply = <&vph_pwr>;
+ vdd_s3-supply = <&vph_pwr>;
+ vdd_s4-supply = <&vph_pwr>;
+ vdd_s5-supply = <&vph_pwr>;
+ vdd_s6-supply = <&vph_pwr>;
+ vdd_s7-supply = <&vph_pwr>;
+ vdd_s8-supply = <&vph_pwr>;
+ vdd_s9-supply = <&vph_pwr>;
+ vdd_s10-supply = <&vph_pwr>;
+ vdd_s11-supply = <&vph_pwr>;
+ vdd_s12-supply = <&vph_pwr>;
+ vdd_s13-supply = <&vph_pwr>;
+ vdd_l1_l27-supply = <&vreg_s7a_1p025>;
+ vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
+ vdd_l3_l11-supply = <&vreg_s7a_1p025>;
+ vdd_l4_l5-supply = <&vreg_s7a_1p025>;
+ vdd_l6-supply = <&vreg_s5a_2p04>;
+ vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
+ vdd_l9-supply = <&vreg_bob>;
+ vdd_l10_l23_l25-supply = <&vreg_bob>;
+ vdd_l13_l19_l21-supply = <&vreg_bob>;
+ vdd_l16_l28-supply = <&vreg_bob>;
+ vdd_l18_l22-supply = <&vreg_bob>;
+ vdd_l20_l24-supply = <&vreg_bob>;
+ vdd_l26-supply = <&vreg_s3a_1p35>;
+ vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+ vreg_s3a_1p35: s3 {
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+ vreg_s4a_1p8: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-allow-set-load;
+ };
+ vreg_s5a_2p04: s5 {
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2040000>;
+ };
+ vreg_s7a_1p025: s7 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1028000>;
+ };
+ vreg_l1a_0p875: l1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ };
+ vreg_l2a_1p2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+ vreg_l3a_1p0: l3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+ vreg_l5a_0p8: l5 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ };
+ vreg_l6a_1p8: l6 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <1808000>;
+ };
+ vreg_l7a_1p8: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l8a_1p2: l8 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+ vreg_l9a_1p8: l9 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ };
+ vreg_l10a_1p8: l10 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ };
+ vreg_l11a_1p0: l11 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+ vreg_l12a_1p8: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l13a_2p95: l13 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ };
+ vreg_l14a_1p88: l14 {
+ regulator-min-microvolt = <1880000>;
+ regulator-max-microvolt = <1880000>;
+ };
+ vreg_l15a_1p8: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l16a_2p7: l16 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+ };
+ vreg_l17a_1p3: l17 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ };
+ vreg_l18a_2p7: l18 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+ };
+ vreg_l19a_3p0: l19 {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ };
+ vreg_l20a_2p95: l20 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-allow-set-load;
+ };
+ vreg_l21a_2p95: l21 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-allow-set-load;
+ regulator-system-load = <800000>;
+ };
+ vreg_l22a_2p85: l22 {
+ regulator-min-microvolt = <2864000>;
+ regulator-max-microvolt = <2864000>;
+ };
+ vreg_l23a_3p3: l23 {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3312000>;
+ };
+ vreg_l24a_3p075: l24 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3088000>;
+ };
+ vreg_l25a_3p3: l25 {
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3312000>;
+ };
+ vreg_l26a_1p2: l26 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-allow-set-load;
+ };
+ vreg_l28_3p0: l28 {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ };
+ vreg_lvs1a_1p8: lvs1 { };
+ vreg_lvs2a_1p8: lvs2 { };
+ };
+
+ pmi8998-regulators {
+ compatible = "qcom,rpm-pmi8998-regulators";
+
+ vdd_bob-supply = <&vph_pwr>;
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3600000>;
+ };
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ hall_sensor_default: hall-sensor-default {
+ pins = "gpio124";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
+ };
+
+ ts_int_active: ts-int-active {
+ pins = "gpio125";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ ts_reset_active: ts-reset-active {
+ pins = "gpio89";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+};
+
+&ufshc {
+ status = "okay";
+
+ vcc-supply = <&vreg_l20a_2p95>;
+ vccq-supply = <&vreg_l26a_1p2>;
+ vccq2-supply = <&vreg_s4a_1p8>;
+ vcc-max-microamp = <750000>;
+ vccq-max-microamp = <560000>;
+ vccq2-max-microamp = <750000>;
+};
+
+&ufsphy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l2a_1p2>;
+ vddp-ref-clk-supply = <&vreg_l26a_1p2>;
+ vdda-phy-max-microamp = <51400>;
+ vdda-pll-max-microamp = <14600>;
+ vddp-ref-clk-max-microamp = <100>;
+ vddp-ref-clk-always-on;
+};
+
+&usb3 {
+ status = "okay";
+
+ /* Disable USB3 clock requirement as the device only supports USB2 */
+ qcom,select-utmi-as-pipe-clk;
+};
+
+&usb3_dwc3 {
+ /* Drop the unused USB 3 PHY */
+ phys = <&qusb2phy>;
+ phy-names = "usb2-phy";
+
+ /* Fastest mode for USB 2 */
+ maximum-speed = "high-speed";
+
+ /* Force to peripheral until we can switch modes */
+ dr_mode = "peripheral";
+};
+
+/* Hold off on WLAN enablement until MSS remoteproc and friends are brought up */
+&wifi {
+ vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts b/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts
new file mode 100644
index 000000000000..b46214a32478
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * OnePlus 5T (dumpling) device tree
+ *
+ * Copyright (c) 2021, Jami Kettunen <jamipkettunen@xxxxxxxxx>
+ */
+
+#include "msm8998-oneplus-common.dtsi"
+
+/ {
+ model = "OnePlus 5T";
+ compatible = "oneplus,dumpling", "qcom,msm8998";
+ /* Required for bootloader to select correct board */
+ qcom,board-id = <8 0 17801 43>;
+};
+
+/* Update the screen height values from 1920 to 2160 on the 5T */
+&framebuffer0 {
+ height = <2160>;
+};
+
+/* Adjust digitizer area height to match the 5T's taller panel */
+&rmi4_f12 {
+ touchscreen-y-mm = <137>;
+};
--
2.30.1
