Hi, On 10/03/21 9:49 pm, Aswath Govindraju wrote: > The following speed modes are now supported in J7200 SoC, > - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1]. > - UHS-I speed modes in MMCSD1 subsystem [1]. > > Add support for UHS-I modes by adding voltage regulator device tree nodes > and corresponding pinmux details, to power cycle and voltage switch cards. > Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1 > device tree nodes. > > Also update the delay values for various speed modes supported, based on > the latest J7200 datasheet[2] nit: Better to mention the datasheet version (as it's not latest anymore). > > [1] - section 12.3.6.1.1 MMCSD Features, in > https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf > > [2] - https://www.ti.com/lit/ds/symlink/dra821a.pdf Er.. this link is already broken. Thanks Kishon > > Signed-off-by: Aswath Govindraju <a-govindraju@xxxxxx> > --- > .../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++ > arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++- > 2 files changed, 54 insertions(+), 2 deletions(-) > > diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts > index b493f939b09a..6f90c3b1cf45 100644 > --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts > +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts > @@ -16,6 +16,29 @@ > stdout-path = "serial2:115200n8"; > bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; > }; > + > + vdd_mmc1: fixedregulator-sd { > + compatible = "regulator-fixed"; > + regulator-name = "vdd_mmc1"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + enable-active-high; > + gpios = <&exp2 2 GPIO_ACTIVE_HIGH>; > + }; > + > + vdd_sd_dv: gpio-regulator-vdd-sd-dv { > + compatible = "regulator-gpio"; > + regulator-name = "vdd_sd_dv"; > + pinctrl-names = "default"; > + pinctrl-0 = <&vdd_sd_dv_pins_default>; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>; > + states = <1800000 0x0 > + 3300000 0x1>; > + }; > }; > > &wkup_pmx0 { > @@ -45,6 +68,13 @@ > }; > > &main_pmx0 { > + main_i2c0_pins_default: main-i2c0-pins-default { > + pinctrl-single,pins = < > + J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */ > + J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ > + >; > + }; > + > main_i2c1_pins_default: main-i2c1-pins-default { > pinctrl-single,pins = < > J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */ > @@ -70,6 +100,12 @@ > J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */ > >; > }; > + > + vdd_sd_dv_pins_default: vdd_sd_dv_pins_default { > + pinctrl-single,pins = < > + J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */ > + >; > + }; > }; > > &wkup_uart0 { > @@ -157,6 +193,10 @@ > }; > > &main_i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&main_i2c0_pins_default>; > + clock-frequency = <400000>; > + > exp1: gpio@20 { > compatible = "ti,tca6416"; > reg = <0x20>; > @@ -206,6 +246,8 @@ > /* SD card */ > pinctrl-0 = <&main_mmc1_pins_default>; > pinctrl-names = "default"; > + vmmc-supply = <&vdd_mmc1>; > + vqmmc-supply = <&vdd_sd_dv>; > ti,driver-strength-ohm = <50>; > disable-wp; > }; > diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi > index e60650a62b14..f86c493a44f1 100644 > --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi > +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi > @@ -512,11 +512,16 @@ > ti,otap-del-sel-mmc-hs = <0x0>; > ti,otap-del-sel-ddr52 = <0x6>; > ti,otap-del-sel-hs200 = <0x8>; > - ti,otap-del-sel-hs400 = <0x0>; > + ti,otap-del-sel-hs400 = <0x5>; > + ti,itap-del-sel-legacy = <0x10>; > + ti,itap-del-sel-mmc-hs = <0xa>; > ti,strobe-sel = <0x77>; > + ti,clkbuf-sel = <0x7>; > ti,trm-icp = <0x8>; > bus-width = <8>; > mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + mmc-hs400-1_8v; > dma-coherent; > }; > > @@ -534,7 +539,12 @@ > ti,otap-del-sel-sdr50 = <0xc>; > ti,otap-del-sel-sdr104 = <0x5>; > ti,otap-del-sel-ddr50 = <0xc>; > - no-1-8-v; > + ti,itap-del-sel-legacy = <0x0>; > + ti,itap-del-sel-sd-hs = <0x0>; > + ti,itap-del-sel-sdr12 = <0x0>; > + ti,itap-del-sel-sdr25 = <0x0>; > + ti,clkbuf-sel = <0x7>; > + ti,trm-icp = <0x8>; > dma-coherent; > }; > >
