Convert the binding to DT schema format.
Signed-off-by: Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxx>
---
.../bindings/power/supply/bq24257.txt | 62 ---------
.../bindings/power/supply/bq24257.yaml | 124 ++++++++++++++++++
2 files changed, 124 insertions(+), 62 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/power/supply/bq24257.txt
create mode 100644 Documentation/devicetree/bindings/power/supply/bq24257.yaml
diff --git a/Documentation/devicetree/bindings/power/supply/bq24257.txt b/Documentation/devicetree/bindings/power/supply/bq24257.txt
deleted file mode 100644
index f8f5a1685bb9..000000000000
--- a/Documentation/devicetree/bindings/power/supply/bq24257.txt
+++ /dev/null
@@ -1,62 +0,0 @@
-Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger
-
-Required properties:
-- compatible: Should contain one of the following:
- * "ti,bq24250"
- * "ti,bq24251"
- * "ti,bq24257"
-- reg: integer, i2c address of the device.
-- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in
- conjunction with "interrupt-parent".
-- ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
-- ti,charge-current: integer, maximum charging current in uA.
-- ti,termination-current: integer, charge will be terminated when current in
- constant-voltage phase drops below this value (in uA).
-
-Optional properties:
-- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin.
- This pin is not available on all devices however it should be used if
- possible as this is the recommended way to obtain the charger's input PG
- state. If this pin is not specified a software-based approach for PG
- detection is used.
-- ti,current-limit: The maximum current to be drawn from the charger's input
- (in uA). If this property is not specified, the input limit current is
- set automatically using USB D+/D- signal based charger type detection.
- If the hardware does not support the D+/D- based detection, a default
- of 500,000 is used (=500mA) instead.
-- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If
- not specified a default of 6,5000,000 (=6.5V) is used.
-- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic
- power path management (in uV). If not specified a default of 4,360,000
- (=4.36V) is used.
-
-Example:
-
-bq24257 {
- compatible = "ti,bq24257";
- reg = <0x6a>;
- interrupt-parent = <&gpio1>;
- interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
-
- pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
-
- ti,battery-regulation-voltage = <4200000>;
- ti,charge-current = <1000000>;
- ti,termination-current = <50000>;
-};
-
-Example:
-
-bq24250 {
- compatible = "ti,bq24250";
- reg = <0x6a>;
- interrupt-parent = <&gpio1>;
- interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
-
- ti,battery-regulation-voltage = <4200000>;
- ti,charge-current = <500000>;
- ti,termination-current = <50000>;
- ti,current-limit = <900000>;
- ti,ovp-voltage = <9500000>;
- ti,in-dpm-voltage = <4440000>;
-};
diff --git a/Documentation/devicetree/bindings/power/supply/bq24257.yaml b/Documentation/devicetree/bindings/power/supply/bq24257.yaml
new file mode 100644
index 000000000000..3a0f6cd9015a
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq24257.yaml
@@ -0,0 +1,124 @@
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (C) 2021 Sebastian Reichel
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/power/supply/bq24257.yaml#";
+$schema: "http://devicetree.org/meta-schemas/core.yaml#";
+
+title: Binding for bq24250, bq24251 and bq24257 Li-Ion Charger
+
+maintainers:
+ - Sebastian Reichel <sre@xxxxxxxxxx>
+
+allOf:
+ - $ref: power-supply.yaml#
+
+properties:
+ compatible:
+ enum:
+ - ti,bq24250
+ - ti,bq24251
+ - ti,bq24257
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ ti,battery-regulation-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: maximum charging voltage in uV
+
+ ti,charge-current:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: maximum charging current in uA
+
+ ti,termination-current:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ charge will be terminated when current in constant-voltage phase
+ drops below this value (in uA)
+
+ pg-gpios:
+ description: |
+ GPIO used for connecting the bq2425x device PG (Power Good) pin.
+ This pin is not available on all devices however it should be used if
+ possible as this is the recommended way to obtain the charger's input PG
+ state. If this pin is not specified a software-based approach for PG
+ detection is used.
+ maxItems: 1
+
+ ti,current-limit:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ The maximum current to be drawn from the charger's input (in uA).
+ If this property is not specified, the input limit current is set
+ automatically using USB D+/D- signal based charger type detection.
+ If the hardware does not support the D+/D- based detection, a default
+ of 500,000 is used (=500mA) instead.
+
+ ti,ovp-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Configures the over voltage protection voltage (in uV).
+ If not specified a default of 6,5000,000 (=6.5V) is used.
+
+ ti,in-dpm-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Configures the threshold input voltage for the dynamic power path management (in uV).
+ If not specified a default of 4,360,000 (=4.36V) is used.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - ti,battery-regulation-voltage
+ - ti,charge-current
+ - ti,termination-current
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@6a {
+ compatible = "ti,bq24257";
+ reg = <0x6a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+ pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+
+ ti,battery-regulation-voltage = <4200000>;
+ ti,charge-current = <1000000>;
+ ti,termination-current = <50000>;
+ };
+ };
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@6a {
+ compatible = "ti,bq24250";
+ reg = <0x6a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+ ti,battery-regulation-voltage = <4200000>;
+ ti,charge-current = <500000>;
+ ti,termination-current = <50000>;
+ ti,current-limit = <900000>;
+ ti,ovp-voltage = <9500000>;
+ ti,in-dpm-voltage = <4440000>;
+ };
+ };
--
2.30.1
