[PATCH v2 2/6] pinctrl: Ingenic: Add support for read the pin configuration of X1830.

[周琰杰 (Zhou Yanjie) <zhouyanjie@xxxxxxxxxxxxxx>]

Add X1830 support in "ingenic_pinconf_get()", so that it can read the
configuration of X1830 SoC correctly.

Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@xxxxxxxxxxxxxx>
---

Notes:
    v2:
    New patch.

 drivers/pinctrl/pinctrl-ingenic.c | 76 +++++++++++++++++++++++++++++----------
 1 file changed, 57 insertions(+), 19 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-ingenic.c b/drivers/pinctrl/pinctrl-ingenic.c
index 05dfa0a..0a88aab 100644
--- a/drivers/pinctrl/pinctrl-ingenic.c
+++ b/drivers/pinctrl/pinctrl-ingenic.c
@@ -2109,31 +2109,69 @@ static int ingenic_pinconf_get(struct pinctrl_dev *pctldev,
 	enum pin_config_param param = pinconf_to_config_param(*config);
 	unsigned int idx = pin % PINS_PER_GPIO_CHIP;
 	unsigned int offt = pin / PINS_PER_GPIO_CHIP;
+	unsigned int bias;
 	bool pull;
 
-	if (jzpc->info->version >= ID_JZ4770)
-		pull = !ingenic_get_pin_config(jzpc, pin, JZ4770_GPIO_PEN);
-	else
-		pull = !ingenic_get_pin_config(jzpc, pin, JZ4740_GPIO_PULL_DIS);
+	if (jzpc->info->version >= ID_X1830) {
+		unsigned int half = PINS_PER_GPIO_CHIP / 2;
+		unsigned int idxh = pin % half * 2;
 
-	switch (param) {
-	case PIN_CONFIG_BIAS_DISABLE:
-		if (pull)
-			return -EINVAL;
-		break;
+		if (idx < half)
+			regmap_read(jzpc->map, offt * jzpc->info->reg_offset +
+					X1830_GPIO_PEL, &bias);
+		else
+			regmap_read(jzpc->map, offt * jzpc->info->reg_offset +
+					X1830_GPIO_PEH, &bias);
 
-	case PIN_CONFIG_BIAS_PULL_UP:
-		if (!pull || !(jzpc->info->pull_ups[offt] & BIT(idx)))
-			return -EINVAL;
-		break;
+		bias = (bias >> idxh) & 3;
 
-	case PIN_CONFIG_BIAS_PULL_DOWN:
-		if (!pull || !(jzpc->info->pull_downs[offt] & BIT(idx)))
-			return -EINVAL;
-		break;
+		switch (param) {
+		case PIN_CONFIG_BIAS_DISABLE:
+			if (bias)
+				return -EINVAL;
+			break;
 
-	default:
-		return -ENOTSUPP;
+		case PIN_CONFIG_BIAS_PULL_UP:
+			if ((bias != PIN_CONFIG_BIAS_PULL_UP) ||
+					!(jzpc->info->pull_ups[offt] & BIT(idx)))
+				return -EINVAL;
+			break;
+
+		case PIN_CONFIG_BIAS_PULL_DOWN:
+			if ((bias != PIN_CONFIG_BIAS_PULL_DOWN) ||
+					!(jzpc->info->pull_downs[offt] & BIT(idx)))
+				return -EINVAL;
+			break;
+
+		default:
+			return -ENOTSUPP;
+		}
+
+	} else {
+		if (jzpc->info->version >= ID_JZ4770)
+			pull = !ingenic_get_pin_config(jzpc, pin, JZ4770_GPIO_PEN);
+		else
+			pull = !ingenic_get_pin_config(jzpc, pin, JZ4740_GPIO_PULL_DIS);
+
+		switch (param) {
+		case PIN_CONFIG_BIAS_DISABLE:
+			if (pull)
+				return -EINVAL;
+			break;
+
+		case PIN_CONFIG_BIAS_PULL_UP:
+			if (!pull || !(jzpc->info->pull_ups[offt] & BIT(idx)))
+				return -EINVAL;
+			break;
+
+		case PIN_CONFIG_BIAS_PULL_DOWN:
+			if (!pull || !(jzpc->info->pull_downs[offt] & BIT(idx)))
+				return -EINVAL;
+			break;
+
+		default:
+			return -ENOTSUPP;
+		}
 	}
 
 	*config = pinconf_to_config_packed(param, 1);
-- 
2.7.4