Hi Valentin
On 2/11/21 12:07 PM, Valentin CARON - foss wrote:
Modify usart 2 & 3 pins to allow wake up from low power mode while the
hardware flow control is activated. UART RTS pin need to stay configure
in idle mode to receive characters in order to wake up.
Fixes: 842ed898a757 ("ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl")
Signed-off-by: Valentin Caron <valentin.caron@xxxxxxxxxxx>
---
Applied on stm32-fixes.
Thanks
Alex
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 21 ++++++++++++++++++---
1 file changed, 18 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index 7b4249ed1983..060baa8b7e9d 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -1891,10 +1891,15 @@
usart2_idle_pins_c: usart2-idle-2 {
pins1 {
pinmux = <STM32_PINMUX('D', 5, ANALOG)>, /* USART2_TX */
- <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
<STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
};
pins2 {
+ pinmux = <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins3 {
pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
bias-disable;
};
@@ -1940,10 +1945,15 @@
usart3_idle_pins_b: usart3-idle-1 {
pins1 {
pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
- <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
<STM32_PINMUX('I', 10, ANALOG)>; /* USART3_CTS_NSS */
};
pins2 {
+ pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins3 {
pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
bias-disable;
};
@@ -1976,10 +1986,15 @@
usart3_idle_pins_c: usart3-idle-2 {
pins1 {
pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
- <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
<STM32_PINMUX('B', 13, ANALOG)>; /* USART3_CTS_NSS */
};
pins2 {
+ pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins3 {
pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
bias-disable;
};
