Re: [PATCH V1] arm64: dts: qcom: sc7280: Add nodes for eMMC and SD card

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 3/10/2021 12:48 AM, Shaik Sajida Bhanu wrote:
Add nodes for eMMC and SD card on sc7280.

Signed-off-by: Shaik Sajida Bhanu <sbhanu@xxxxxxxxxxxxxx>

---
This change is depends on the below patch series:
https://lore.kernel.org/lkml/1613114930-1661-1-git-send-email-rnayak@xxxxxxxxxxxxxx/
https://lore.kernel.org/patchwork/project/lkml/list/?series=&submitter=28035&state=&q=&archive=&delegate=
---
  arch/arm64/boot/dts/qcom/sc7280-idp.dts |  26 +++++
  arch/arm64/boot/dts/qcom/sc7280.dtsi    | 170 ++++++++++++++++++++++++++++++++
  2 files changed, 196 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index ac79420..6abb2aa 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -8,6 +8,7 @@
  /dts-v1/;
#include "sc7280.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
  	model = "Qualcomm Technologies, Inc. SC7280 IDP platform";
@@ -256,3 +257,28 @@
  		bias-pull-up;
  	};
  };
+
+&sdhc_1 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+
+	vmmc-supply = <&vreg_l7b_2p9>;
+	vqmmc-supply = <&vreg_l19b_1p8>;
+
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+
+	vmmc-supply = <&vreg_l9c_2p9>;
+	vqmmc-supply = <&vreg_l6c_2p9>;
+
+	cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 3b86052..91fb18a 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -18,6 +18,11 @@
chosen { }; + aliases {
+		mmc1 = &sdhc_1;
+		mmc2 = &sdhc_2;
+	};
+
  	clocks {
  		xo_board: xo-board {
  			compatible = "fixed-clock";
@@ -315,6 +320,69 @@
  			#power-domain-cells = <1>;
  		};
+ sdhc_1: sdhci@7c4000 {
+			compatible = "qcom,sdhci-msm-v5";
+			reg = <0 0x7c4000 0 0x1000>,
+					<0 0x7c5000 0 0x1000>;
+			reg-names = "hc", "cqhci";
+
+			iommus = <&apps_smmu 0xC0 0x0>;
+			interrupts = <GIC_SPI 652 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
+					<&gcc GCC_SDCC1_AHB_CLK>,
+					<&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "core", "iface", "xo";
+
+			bus-width = <8>;
+			non-removable;
+			supports-cqe;
+			no-sd;
+			no-sdio;
+
+			max-frequency = <192000000>;
+
+			qcom,dll-config = <0x0007642c>;
+			qcom,ddr-config = <0x80040868>;
+
+			mmc-ddr-1_8v;
+			mmc-hs200-1_8v;
+			mmc-hs400-1_8v;
+			mmc-hs400-enhanced-strobe;
+
+			status = "disabled";
+
+		};
+
+		sdhc_2: sdhci@8804000 {
+			compatible = "qcom,sdhci-msm-v5";
+			reg = <0 0x08804000 0 0x1000>;
+
+			iommus = <&apps_smmu 0x100 0x0>;
+			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
+					<&gcc GCC_SDCC2_AHB_CLK>,
+					<&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "core", "iface", "xo";
+
+			bus-width = <4>;
+
+			no-mmc;
+			no-sdio;
+
+			max-frequency = <202000000>;
+
+			qcom,dll-config = <0x0007642c>;
+
+			status = "disabled";
+
+		};
+
  		qupv3_id_0: geniqup@9c0000 {
  			compatible = "qcom,geni-se-qup";
  			reg = <0 0x009c0000 0 0x2000>;
@@ -385,6 +453,108 @@
  				pins = "gpio46", "gpio47";
  				function = "qup13";
  			};
+
+			sdc1_on: sdc1-on {
+				pinconf-clk {
+					pins = "sdc1_clk";
+					bias-disable;
+					drive-strength = <16>;
+				};
+
+				pinconf-cmd {
+					pins = "sdc1_cmd";
+					bias-pull-up;
+					drive-strength = <10>;
+				};
+
+				pinconf-data {
+					pins = "sdc1_data";
+					bias-pull-up;
+					drive-strength = <10>;
+				};
+
+				pinconf-rclk {
+					pins = "sdc1_rclk";
+					bias-pull-down;
+				};
+			};
+
+			sdc1_off: sdc1-off {
+				pinconf-clk {
+					pins = "sdc1_clk";
+					bias-disable;
+					drive-strength = <2>;
+				};
+
+				pinconf-cmd {
+					pins = "sdc1_cmd";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				pinconf-data {
+					pins = "sdc1_data";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				pinconf-rclk {
+					pins = "sdc1_rclk";
+					bias-pull-down;
+				};
+			};
+
+			sdc2_on: sdc2-on {
+				pinconf-clk {
+					pins = "sdc2_clk";
+					bias-disable;
+					drive-strength = <16>;
+				};
+
+				pinconf-cmd {
+					pins = "sdc2_cmd";
+					bias-pull-up;
+					drive-strength = <10>;
+				};
+
+				pinconf-data {
+					pins = "sdc2_data";
+					bias-pull-up;
+					drive-strength = <10>;
+				};
+
+				pinconf-sd-cd {
+					pins = "gpio91";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+			};
+
+			sdc2_off: sdc2-off {
+				pinconf-clk {
+					pins = "sdc2_clk";
+					bias-disable;
+					drive-strength = <2>;
+				};
+
+				pinconf-cmd {
+					pins = "sdc2_cmd";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				pinconf-data {
+					pins = "sdc2_data";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				pinconf-sd-cd {
+					pins = "gpio91";
+					bias-disable;
On few sc7180 based boards where external pull up is missing on cd-gpio,
we had seen issues like un-intended interrupt on cd-gpio pin (since its
getting toggled) during runtime PM cycle and resulting in unnecessary
scheduling of SDcard scan (mmc_rescan). This issue is seen only when SDcard
is not present.
By enabling internal pull all the time (bais-pull-up), we can avoid such issue.

+					drive-strength = <2>;
+				};
+			};
  		};
apps_smmu: iommu@15000000 {



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux