Hi, This series adds LCD I80 interface display support for Exynos DRM driver. The FIMD(display controller) specification describes it as "LCD I80 interface" and the DSI specification describes it as "Command mode interface". This is based on exynos-drm-next branch. The previous patches, RFC: http://www.spinics.net/lists/dri-devel/msg58898.html V1: http://www.spinics.net/lists/dri-devel/msg59291.html V2: http://www.spinics.net/lists/dri-devel/msg59867.html V3: http://www.spinics.net/lists/dri-devel/msg60708.html V4: http://www.spinics.net/lists/dri-devel/msg60943.html Changelog v2: - Fixes typo and removes unnecessary error log (commented by Andrzej Hazda) - Adds missed pendlig_flip flag clear points (commented by Daniel Kurtz) Changelog v3: - Removes generic command mode and command mode display timing interface. - Moves I80 interface timings from panel DT to the FIMD(display controller) DT. Changelog v4: - Removes exynos5 sysreg(syscon) DT bindings and node from dtsi because it was already updated by linux-samsung-soc (commented by Vivek Gautam) Changelog v5: - Fixes FIMD vidcon0 register relevant code - Fixes panel gamma table, disable sequence - Slitely updates for code cleanup Patches 1 and 2 fix trivial bugs. Patches 3, 4, 5 and 6 implement FIMD(display controller) I80 interface. The MIPI DSI command mode based panel generates Tearing Effect synchronization signal between MCU and FB to display video image, and FIMD should trigger to transfer video image at this signal. So the panel should receive the TE IRQ and call TE handler chains to notify it to the FIMD. Patches 7 and 8 implement to use Exynos5410 / 5420 / 5440 SoC DSI driver which is different from previous Exynos4 SoCs for some registers control. Patches 9 and 10 introduce MIPI DSI command mode based Samsung S6E3FA0 AMOLED 5.7" LCD drm panel driver. The ohters add DT property nodes to support MIPI DSI command mode. I welcome any comments. Thank you. Best regards YJ YoungJun Cho (14): drm/exynos: dsi: move the EoT packets configuration point drm/exynos: use wait_event_timeout() for safety usage ARM: dts: samsung-fimd: add LCD I80 interface specific properties drm/exynos: add TE handler to support LCD I80 interface drm/exynos: dsi: add pass TE host ops to support LCD I80 interface drm/exynos: fimd: support LCD I80 interface ARM: dts: exynos_dsim: add exynos5410 compatible to DT bindings drm/exynos: dsi: add driver data to support Exynos5410/5420/5440 SoCs ARM: dts: s6e3fa0: add DT bindings drm/panel: add S6E3FA0 driver ARM: dts: exynos4: add system register property ARM: dts: exynos5: add system register property ARM: dts: exynos5420: add mipi-phy node ARM: dts: exynos5420: add dsi node .../devicetree/bindings/panel/samsung,s6e3fa0.txt | 46 ++ .../devicetree/bindings/video/exynos_dsim.txt | 4 +- .../devicetree/bindings/video/samsung-fimd.txt | 28 + arch/arm/boot/dts/exynos4.dtsi | 1 + arch/arm/boot/dts/exynos5.dtsi | 1 + arch/arm/boot/dts/exynos5420.dtsi | 20 + drivers/gpu/drm/exynos/Kconfig | 1 + drivers/gpu/drm/exynos/exynos_drm_crtc.c | 15 +- drivers/gpu/drm/exynos/exynos_drm_crtc.h | 7 + drivers/gpu/drm/exynos/exynos_drm_drv.h | 3 + drivers/gpu/drm/exynos/exynos_drm_dsi.c | 181 ++++++- drivers/gpu/drm/exynos/exynos_drm_fimd.c | 276 ++++++++-- drivers/gpu/drm/panel/Kconfig | 7 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-s6e3fa0.c | 569 +++++++++++++++++++++ include/drm/drm_mipi_dsi.h | 7 + include/video/samsung_fimd.h | 3 +- 17 files changed, 1098 insertions(+), 72 deletions(-) create mode 100644 Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt create mode 100644 drivers/gpu/drm/panel/panel-s6e3fa0.c -- 1.9.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
