On 3/3/21 11:47 AM, Abel Vesa wrote:
On 20-11-03 13:18:12, Abel Vesa wrote:
The BLK_CTL according to HW design is basically the wrapper of the entire
function specific group of IPs and holds GPRs that usually cannot be placed
into one specific IP from that group. Some of these GPRs are used to control
some clocks, other some resets, others some very specific function that does
not fit into clocks or resets. Since the clocks are registered using the i.MX
clock subsystem API, the driver is placed into the clock subsystem, but it
also registers the resets. For the other functionalities that other GPRs might
have, the syscon is used.
This approach seems to be introducing a possible ABBA deadlock due to
the core clock and genpd locking. Here is a backtrace I got from Pete
Zhang (he reported the issue on the internal mailing list):
[ 11.667711][ T108] -> #1 (&genpd->mlock){+.+.}-{3:3}:
[ 11.675041][ T108] __lock_acquire+0xae4/0xef8
[ 11.680093][ T108] lock_acquire+0xfc/0x2f8
[ 11.684888][ T108] __mutex_lock+0x90/0x870
[ 11.689685][ T108] mutex_lock_nested+0x44/0x50
[ 11.694826][ T108] genpd_lock_mtx+0x18/0x24
[ 11.699706][ T108] genpd_runtime_resume+0x90/0x214 (hold genpd->mlock)
[ 11.705194][ T108] __rpm_callback+0x80/0x2c0
[ 11.710160][ T108] rpm_resume+0x468/0x650
[ 11.714866][ T108] __pm_runtime_resume+0x60/0x88
[ 11.720180][ T108] clk_pm_runtime_get+0x28/0x9c
[ 11.725410][ T108] clk_disable_unused_subtree+0x8c/0x144
[ 11.731420][ T108] clk_disable_unused_subtree+0x124/0x144
[ 11.737518][ T108] clk_disable_unused+0xa4/0x11c (hold prepare_lock)
[ 11.742833][ T108] do_one_initcall+0x98/0x178
[ 11.747888][ T108] do_initcall_level+0x9c/0xb8
[ 11.753028][ T108] do_initcalls+0x54/0x94
[ 11.757736][ T108] do_basic_setup+0x24/0x30
[ 11.762614][ T108] kernel_init_freeable+0x70/0xa4
[ 11.768014][ T108] kernel_init+0x14/0x18c
[ 11.772722][ T108] ret_from_fork+0x10/0x18
[ 11.777512][ T108] -> #0 (prepare_lock){+.+.}-{3:3}:
[ 11.784749][ T108] check_noncircular+0x134/0x13c
[ 11.790064][ T108] validate_chain+0x590/0x2a04
[ 11.795204][ T108] __lock_acquire+0xae4/0xef8
[ 11.800258][ T108] lock_acquire+0xfc/0x2f8
[ 11.805050][ T108] __mutex_lock+0x90/0x870
[ 11.809841][ T108] mutex_lock_nested+0x44/0x50
[ 11.814983][ T108] clk_unprepare+0x5c/0x100 ((hold prepare_lock))
[ 11.819864][ T108] imx8m_pd_power_off+0xac/0x110
[ 11.825179][ T108] genpd_power_off+0x1b4/0x2dc
[ 11.830318][ T108] genpd_power_off_work_fn+0x38/0x58 (hold genpd->mlock)
[ 11.835981][ T108] process_one_work+0x270/0x444
[ 11.841208][ T108] worker_thread+0x280/0x4e4
[ 11.846176][ T108] kthread+0x13c/0x14
[ 11.850621][ T108] ret_from_fork+0x10/0x18
Now, this has been reproduced only on the NXP internal tree, but I think
it is pretty obvious this could happen in upstream too, with this
patchset applied.
First, my thought was to change the prepare_lock/enable_lock in clock
core, from a global approach to a per clock basis. But that doesn't
actually fix the issue.
The usecase seen above is due to clk_disable_unused, but the same could
happen when a clock consumer calls prepare/unprepare on a clock.
I guess the conclusion is that the current state of the clock core and
genpd implementation does not support a usecase where a clock controller
has a PD which in turn uses another clock (from another clock controller).
Jacky, Pete, did I miss anything here ?
Just for completeness, I have a feeling I already managed to trigger
this and discussed this with Lucas before, so this concern is certainly
valid.
