On Thu, Feb 18, 2021 at 01:33:29PM +0100, Heiko Thiery wrote:
> The Kontron pitx-imx8m board is based on an i.MX8MQ soc.
>
> Signed-off-by: Heiko Thiery <heiko.thiery@xxxxxxxxx>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../freescale/imx8mq-kontron-pitx-imx8m.dts | 675 ++++++++++++++++++
> 2 files changed, 676 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 6438db3822f8..9fc2c6f64407 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -47,6 +47,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mq-kontron-pitx-imx8m.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
> new file mode 100644
> index 000000000000..79805928204e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
> @@ -0,0 +1,675 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree File for the Kontron pitx-imx8m board.
> + *
> + * Copyright (C) 2021 Heiko Thiery <heiko.thiery@xxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mq.dtsi"
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/ {
> + model = "Kontron pITX-imx8m";
> + compatible = "kontron,pitx-imx8m", "fsl,imx8mq";
> +
> + aliases {
> + i2c0 = &i2c1;
> + i2c1 = &i2c2;
> + i2c2 = &i2c3;
> + mmc0 = &usdhc1;
> + mmc1 = &usdhc2;
> + serial0 = &uart1;
> + serial1 = &uart2;
> + serial2 = &uart3;
> + spi0 = &qspi0;
> + spi1 = &ecspi2;
> + };
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_usdhc2_vmmc: regulator-v-3v3-sd {
That's a messed unit addressing. You have here simple-bus but no unit
addresses. Move it out of regulators node and run make dtc W=1 (it would
point you this issue).
> + compatible = "regulator-fixed";
> + regulator-name = "V_3V3_SD";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + off-on-delay-us = <20000>;
> + enable-active-high;
> + };
> + };
> +
> + usb_hub_reset: usb-hub-reset {
> + compatible = "gpio-reset";
> + reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
> + reset-delay-us = <3000>;
> + reset-post-delay-ms = <50>;
> + #reset-cells = <0>;
> + };
> +
> + tpm_reset: tpm-reset {
> + compatible = "gpio-reset";
> + reset-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
> + reset-delay-us = <2>;
> + reset-post-delay-ms = <60>;
> + #reset-cells = <0>;
> + };
> +
> + pcie0_refclk: pcie0-refclk {
Generic node names (from the dt spec candidate is "clock").
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <100000000>;
> + };
> +
> + pcie1_refclk: pcie1-refclk {
Same.
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <100000000>;
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> + pciewake {
> + label = "PCIE_Wake";
> + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
> + linux,input-type = <4>; /* EV_MSC */
> + linux,code = <3>; /* MSC_RAW */
> + gpio-key,wakeup;
> + };
> + };
> +};
> +
> +&ecspi2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
> + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +
> + slb9670@0 {
This needs a generic node name.
> + compatible = "infineon,slb9670";
> + reg = <0>;
> + resets = <&tpm_reset>;
> + spi-max-frequency = <43000000>;
> + };
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy0>;
> + phy-reset-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
> + fsl,magic-packet;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
> + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pmic@8 {
> + compatible = "fsl,pfuze100";
> + fsl,pfuze-support-disable-sw;
> + reg = <0x8>;
> +
> + regulators {
> + sw1a_reg: sw1ab {
> + regulator-name = "V_0V9_GPU";
> + regulator-min-microvolt = <825000>;
> + regulator-max-microvolt = <1100000>;
> + };
> +
> + sw1c_reg: sw1c {
> + regulator-name = "V_0V9_VPU";
> + regulator-min-microvolt = <825000>;
> + regulator-max-microvolt = <1100000>;
> + };
> +
> + sw2_reg: sw2 {
> + regulator-name = "V_1V1_NVCC_DRAM";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + };
> +
> + sw3a_reg: sw3ab {
> + regulator-name = "V_1V0_DRAM";
> + regulator-min-microvolt = <825000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + };
> +
> + sw4_reg: sw4 {
> + regulator-name = "V_1V8_S0";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + swbst_reg: swbst {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5150000>;
> + };
> +
> + snvs_reg: vsnvs {
> + regulator-name = "V_0V9_SNVS";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> + };
> +
> + vref_reg: vrefddr {
> + regulator-name = "V_0V55_VREF_DDR";
> + regulator-always-on;
> + };
> +
> + vgen1_reg: vgen1 {
> + regulator-name = "V_1V5_CSI";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + };
> +
> + vgen2_reg: vgen2 {
> + regulator-name = "V_0V9_PHY";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <975000>;
> + regulator-always-on;
> + };
> +
> + vgen3_reg: vgen3 {
> + regulator-name = "V_1V8_PHY";
> + regulator-min-microvolt = <1675000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-always-on;
> + };
> +
> + vgen4_reg: vgen4 {
> + regulator-name = "V_1V8_VDDA";
> + regulator-min-microvolt = <1625000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-always-on;
> + };
> +
> + vgen5_reg: vgen5 {
> + regulator-name = "V_3V3_PHY";
> + regulator-min-microvolt = <3075000>;
> + regulator-max-microvolt = <3625000>;
> + regulator-always-on;
> + };
> +
> + vgen6_reg: vgen6 {
> + regulator-name = "V_2V8_CAM";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> + };
> + };
> +
> + max6650@1b {
Generic node name.
> + compatible = "maxim,max6650";
> + reg = <0x1b>;
> + maxim,fan-microvolt = <5000000>;
> + };
> +
> + rtc@32 {
> + compatible = "microcrystal,rv8803";
> + reg = <0x32>;
> + };
> +
> + lm75@4b {
Node name: sensor.
> + compatible = "national,lm75b";
> + reg = <0x4b>;
> + };
> +
> + eeprom@51 {
> + compatible = "atmel,24c32";
> + reg = <0x51>;
> + pagesize = <32>;
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +
> + wm8904: audio-codec@1a {
> + compatible = "wlf,wm8904";
> + reg = <0x1a>;
> + clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>;
> + clock-names = "mclk";
> + clock-frequency = <24000000>;
> + };
> +};
> +
> +/* M.2 B-key slot */
> +&pcie0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie0>;
> + disable-gpio = <&gpio5 29 GPIO_ACTIVE_LOW>;
> + reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
> + clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,
> + <&clk IMX8MQ_CLK_PCIE1_AUX>,
> + <&clk IMX8MQ_CLK_PCIE1_PHY>,
> + <&pcie0_refclk>;
> + clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
> + ext_osc = <1>;
> + status = "okay";
> +};
> +
> +/* Intel Ethernet Controller I210/I211 */
> +&pcie1 {
> + clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
> + <&clk IMX8MQ_CLK_PCIE2_AUX>,
> + <&clk IMX8MQ_CLK_PCIE2_PHY>,
> + <&pcie1_refclk>;
> + clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
> + ext_osc = <1>;
> + fsl,max-link-speed = <1>;
> + status = "okay";
> +};
> +
> +&pgc_gpu {
> + power-supply = <&sw1a_reg>;
> +};
> +
> +&pgc_vpu {
> + power-supply = <&sw1c_reg>;
> +};
> +
> +&qspi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_qspi>;
> + status = "okay";
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
> + m25p,fast-read;
> + spi-max-frequency = <50000000>;
> + };
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + assigned-clocks = <&clk IMX8MQ_CLK_UART1>;
> + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + assigned-clocks = <&clk IMX8MQ_CLK_UART2>;
> + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + fsl,uart-has-rtscts;
> + assigned-clocks = <&clk IMX8MQ_CLK_UART3>;
> + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
> + status = "okay";
> +};
> +
> +&usb_dwc3_0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb0>;
> + dr_mode = "otg";
> + hnp-disable;
> + srp-disable;
> + adp-disable;
> + maximum-speed = "high-speed";
> + status = "okay";
> +};
> +
> +&usb3_phy0 {
> + status = "okay";
> +};
> +
> +&usb_dwc3_1 {
> + resets = <&usb_hub_reset>;
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usb3_phy1 {
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>;
> + assigned-clock-rates = <400000000>;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> + vqmmc-supply = <&sw4_reg>;
> + bus-width = <8>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>;
> + assigned-clock-rates = <200000000>;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
> + bus-width = <4>;
> + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> + wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
> + vmmc-supply = <®_usdhc2_vmmc>;
> + status = "okay";
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 /* TPM Reset */
> + MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19 /* USB2 Hub Reset */
> + >;
> + };
> +
> + pinctrl_gpio: gpiogrp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x19 /* GPIO0 */
> + MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19 /* GPIO1 */
> + MX8MQ_IOMUXC_NAND_WE_B_GPIO3_IO17 0x19 /* GPIO2 */
> + MX8MQ_IOMUXC_NAND_WP_B_GPIO3_IO18 0x19 /* GPIO3 */
> + MX8MQ_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 /* GPIO4 */
> + MX8MQ_IOMUXC_NAND_DATA04_GPIO3_IO10 0x19 /* GPIO5 */
> + MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x19 /* GPIO6 */
> + MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x19 /* GPIO7 */
> + >;
> + };
> +
> + pinctrl_pcie0: pcie0grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x16 /* PCIE_PERST */
> + MX8MQ_IOMUXC_UART4_TXD_GPIO5_IO29 0x16 /* W_DISABLE */
> + >;
> + };
> +
> + pinctrl_gpio_keys: gpio-keysgrp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x16 /* PCIE_WAKE */
> + >;
> + };
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
> + MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23
> + MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
> + MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
> + MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
> + MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
> + MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
> + MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
> + MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
> + MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
> + MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
> + MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
> + MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
> + MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
> + MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x16
> + MX8MQ_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x16
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
> + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f
> + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f
> + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f
> + >;
> + };
> +
> + pinctrl_qspi: qspigrp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82
> + MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
> + MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
> + MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
> + MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
> + MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
> +
No need for empty line.
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x19
> + MX8MQ_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x19
> + MX8MQ_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x19
> + >;
> + };
> +
> + pinctrl_ecspi2_cs: ecspi2cs {
ecspi2csgrp to match schema
Please run dtbs_check on your DTS.
Best regards,
Krzysztof
