Re: [PATCH v3 5/5] PCI: add PCI controller for Keystone PCIe h/w

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Mon, Jun 30, 2014 at 05:45:20PM -0400, Murali Karicheri wrote:
> Keystone PCIe controller is based on v3.65 version of the
> designware h/w. Main differences are
> 	1. No ATU support
> 	2. Legacy and MSI irq functions are implemented in
> 	   application register space
> 	3. MSI interrupts are multiplexed over 8 IRQ lines to the Host
> 	   side.
> All of the Application register space handing code are organized into
> pci-keystone-dw.c and the functions are called from pci-keystone.c
> to implement PCI controller driver. Also add necessary DT documentation
> for the driver.

I didn't review this code, but have a few minor comments below.

> Signed-off-by: Murali Karicheri <m-karicheri2@xxxxxx>
> 
> CC: Santosh Shilimkar <santosh.shilimkar@xxxxxx>
> CC: Russell King <linux@xxxxxxxxxxxxxxxx>
> CC: Grant Likely <grant.likely@xxxxxxxxxx>
> CC: Rob Herring <robh+dt@xxxxxxxxxx>
> CC: Mohit Kumar <mohit.kumar@xxxxxx>
> CC: Jingoo Han <jg1.han@xxxxxxxxxxx>
> CC: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
> CC: Pratyush Anand <pratyush.anand@xxxxxx>
> CC: Richard Zhu <r65037@xxxxxxxxxxxxx>
> CC: Kishon Vijay Abraham I <kishon@xxxxxx>
> CC: Marek Vasut <marex@xxxxxxx>
> CC: Arnd Bergmann <arnd@xxxxxxxx>
> CC: Pawel Moll <pawel.moll@xxxxxxx>
> CC: Mark Rutland <mark.rutland@xxxxxxx>
> CC: Ian Campbell <ijc+devicetree@xxxxxxxxxxxxxx>
> CC: Kumar Gala <galak@xxxxxxxxxxxxxx>
> CC: Randy Dunlap <rdunlap@xxxxxxxxxxxxx>
> CC: Grant Likely <grant.likely@xxxxxxxxxx>
> ---
>  .../devicetree/bindings/pci/pci-keystone.txt       |   69 +++
>  drivers/pci/host/Kconfig                           |    5 +
>  drivers/pci/host/Makefile                          |    1 +
>  drivers/pci/host/pci-keystone-dw.c                 |  523 ++++++++++++++++++++
>  drivers/pci/host/pci-keystone.c                    |  381 ++++++++++++++
>  drivers/pci/host/pci-keystone.h                    |   56 +++
>  6 files changed, 1035 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pci/pci-keystone.txt
>  create mode 100644 drivers/pci/host/pci-keystone-dw.c
>  create mode 100644 drivers/pci/host/pci-keystone.c
>  create mode 100644 drivers/pci/host/pci-keystone.h
> 
> diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt
> new file mode 100644
> index 0000000..bb39601
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt
> @@ -0,0 +1,69 @@
> +TI Keystone PCIe interface
> +
> +Keystone PCI host Controller is based on Designware PCI h/w version 3.65.
> +It shares common functions with PCIE Designware core driver and inherit
> +common properties defined in
> +Documentation/devicetree/bindings/pci/designware-pci.txt
> +Compatibility string "dw,snps-pcie-v3.65" is used to identify the verison
> +of the DW h/w used on Keystone.
> +
> +Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt
> +for the details of designware DT bindings. Additional properties are
> +described here as well propeties that are not applicable.
> +
> +Required Properties:-
> +
> +compatibility: "ti,keystone-pcie"
> +reg:	index 1 is the base address and length of DW application registers.
> +	index 2 is the base address and length of PCI mode configuration
> +	register.
> +	index 3 is the base address and length of PCI device ID register.
> +
> +pcie_msi_intc : Interrupt controller device node for MSI irq chip
> +	interrupt-cells: should be set to 1
> +	interrupt-parent: Parent interrupt controller phandle
> +	interrupts: GIC interrupt lines connected to PCI MSI interrupt lines
> +
> + Example:
> +	pcie_msi_intc: msi-interrupt-controller {
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +			interrupt-parent = <&gic>;
> +			interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
> +					<GIC_SPI 31 IRQ_TYPE_EDGE_RISING>,
> +					<GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
> +					<GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
> +					<GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
> +					<GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
> +					<GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
> +					<GIC_SPI 37 IRQ_TYPE_EDGE_RISING>;
> +	};
> +
> +pcie_intc: Interrupt controller device node for Legacy irq chip
> +	interrupt-cells: should be set to 1
> +	interrupt-parent: Parent interrupt controller phandle
> +	interrupts: GIC interrupt lines connected to PCI Legacy interrupt lines
> +
> + Example:
> +	pcie_intc: legacy-interrupt-controller {
> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>,
> +			<GIC_SPI 27 IRQ_TYPE_EDGE_RISING>,
> +			<GIC_SPI 28 IRQ_TYPE_EDGE_RISING>,
> +			<GIC_SPI 29 IRQ_TYPE_EDGE_RISING>;
> +	};
> +
> +Optional properties:-
> +	phys: phandle to Generic Keystone SerDes phy for PCI
> +	phy-names: name of the Generic Keystine SerDes phy for PCI
> +	  - If boot loader already does PCI link establishment, then phys and
> +	    phy-names shouldn't be present.
> +	ti,enable-linktrain - Enable Link training.
> +	  - If boot loader already does PCI link establishment, then this
> +	    shouldn't be present.
> +
> +Designware DT Properties not applicable for Keystone PCI
> +
> +1. pcie_bus clock-names not used. Instead, a phandle to phys is used.
> diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
> index 21df477..f8bc475 100644
> --- a/drivers/pci/host/Kconfig
> +++ b/drivers/pci/host/Kconfig
> @@ -46,4 +46,9 @@ config PCI_HOST_GENERIC
>  	  Say Y here if you want to support a simple generic PCI host
>  	  controller, such as the one emulated by kvmtool.
>  
> +config PCI_KEYSTONE
> +	bool "TI Keystone PCIe controller"
> +	depends on ARCH_KEYSTONE
> +	select PCIE_DW
> +	select PCIEPORTBUS
>  endmenu
> diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
> index 611ba4b..d1b6ce1 100644
> --- a/drivers/pci/host/Makefile
> +++ b/drivers/pci/host/Makefile
> @@ -6,3 +6,4 @@ obj-$(CONFIG_PCI_TEGRA) += pci-tegra.o
>  obj-$(CONFIG_PCI_RCAR_GEN2) += pci-rcar-gen2.o
>  obj-$(CONFIG_PCI_RCAR_GEN2_PCIE) += pcie-rcar.o
>  obj-$(CONFIG_PCI_HOST_GENERIC) += pci-host-generic.o
> +obj-$(CONFIG_PCI_KEYSTONE) += pci-keystone-dw.o pci-keystone.o
> diff --git a/drivers/pci/host/pci-keystone-dw.c b/drivers/pci/host/pci-keystone-dw.c
> new file mode 100644
> index 0000000..3b5b075
> --- /dev/null
> +++ b/drivers/pci/host/pci-keystone-dw.c
> @@ -0,0 +1,523 @@
> +/*
> + * Designware application register space functions for Keystone PCI controller
> + *
> + * Copyright (C) 2013-2014 Texas Instruments., Ltd.
> + *		http://www.ti.com
> + *
> + * Author: Murali Karicheri <m-karicheri2@xxxxxx>
> + *
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/irq.h>
> +#include <linux/irqdomain.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_pci.h>
> +#include <linux/pci.h>
> +#include <linux/platform_device.h>
> +
> +#include "pcie-designware.h"
> +#include "pci-keystone.h"
> +
> +/* Application register defines */
> +#define LTSSM_EN_VAL		        BIT(0)
> +#define LTSSM_STATE_MASK	        0x1f
> +#define LTSSM_STATE_L0		        0x11
> +#define DIR_SPD				(1 << 17)
> +#define DBI_CS2_EN_VAL		        BIT(5)
> +#define OB_XLAT_EN_VAL		        BIT(1)

It's sort of confusing to mix "BIT(x)" with the hex masks.  Personally I
think it's easier to read the plain hex masks.

> +/* Application registers */
> +#define CMD_STATUS			0x004
> +#define CFG_SETUP			0x008
> +#define OB_SIZE				0x030
> +#define CFG_PCIM_WIN_SZ_IDX	        3
> +#define CFG_PCIM_WIN_CNT	        32
> +#define SPACE0_REMOTE_CFG_OFFSET	0x1000
> +#define OB_OFFSET_INDEX(n)		(0x200 + (8 * n))
> +#define OB_OFFSET_HI(n)			(0x204 + (8 * n))
> +
> +/* IRQ register defines */
> +#define IRQ_EOI                         0x050
> +#define IRQ_STATUS			0x184
> +#define IRQ_ENABLE_SET			0x188
> +#define IRQ_ENABLE_CLR			0x18c
> +
> +#define MSI_IRQ				0x054
> +#define MSI0_IRQ_STATUS			0x104
> +#define MSI0_IRQ_ENABLE_SET		0x108
> +#define MSI0_IRQ_ENABLE_CLR		0x10c
> +#define IRQ_STATUS			0x184
> +#define MSI_IRQ_OFFSET			4
> +
> +/* Config space registers */
> +#define DEBUG0			        0x728
> +
> +#define to_keystone_pcie(x)	container_of(x, struct keystone_pcie, pp)
> +
> +static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys)
> +{
> +	return sys->private_data;
> +}
> +
> +static inline void update_reg_offset_bit_pos(u32 offset, u32 *reg_offset,
> +					u32 *bit_pos)
> +{
> +	*reg_offset = offset % 8;
> +	*bit_pos = offset >> 3;
> +}
> +
> +inline u32 ks_dw_pcie_get_msi_data(struct pcie_port *pp)

I don't think this should be marked "inline".

> +{
> +	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
> +
> +	return ks_pcie->app.start + MSI_IRQ;
> +}
> +
> +void ks_dw_pcie_handle_msi_irq(struct keystone_pcie *ks_pcie , int offset)
> +{
> +	struct pcie_port *pp = &ks_pcie->pp;
> +	u32 pending, vector;
> +	int src, virq;
> +
> +	pending = readl(ks_pcie->va_app_base + MSI0_IRQ_STATUS + (offset << 4));
> +	/*
> +	 * MSI0, Status bit 0-3 shows vectors 0, 8, 16, 24, MSI1 status bit
> +	 * shows 1, 9, 17, 25 and so forth
> +	 */
> +	for (src = 0; src < 4; src++) {
> +		if (BIT(src) & pending) {
> +			vector = offset + (src << 3);
> +			virq = irq_linear_revmap(pp->irq_domain, vector);
> +			dev_dbg(pp->dev,
> +				"irq: bit %d, vector %d, virq %d\n",
> +				 src, vector, virq);
> +			generic_handle_irq(virq);
> +		}
> +	}
> +}
> +
> +static void ks_dw_pcie_msi_irq_ack(struct irq_data *d)
> +{
> +	u32 offset, reg_offset, bit_pos;
> +	struct keystone_pcie *ks_pcie;
> +	unsigned int irq = d->irq;
> +	struct msi_desc *msi;
> +	struct pcie_port *pp;
> +
> +	msi = irq_get_msi_desc(irq);
> +	pp = sys_to_pcie(msi->dev->bus->sysdata);
> +	ks_pcie = to_keystone_pcie(pp);
> +	offset = irq - irq_linear_revmap(pp->irq_domain, 0);
> +	update_reg_offset_bit_pos(offset, &reg_offset, &bit_pos);
> +
> +	writel(BIT(bit_pos),
> +		ks_pcie->va_app_base + MSI0_IRQ_STATUS + (reg_offset << 4));
> +	writel(reg_offset + MSI_IRQ_OFFSET, ks_pcie->va_app_base + IRQ_EOI);
> +}
> +
> +void ks_dw_pcie_msi_set_irq(struct pcie_port *pp, int irq)
> +{
> +	u32 reg_offset, bit_pos;
> +	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
> +
> +	update_reg_offset_bit_pos(irq, &reg_offset, &bit_pos);
> +	writel(BIT(bit_pos),
> +		ks_pcie->va_app_base + MSI0_IRQ_ENABLE_SET + (reg_offset << 4));
> +}
> +
> +void ks_dw_pcie_msi_clear_irq(struct pcie_port *pp, int irq)
> +{
> +	u32 reg_offset, bit_pos;
> +	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
> +
> +	update_reg_offset_bit_pos(irq, &reg_offset, &bit_pos);
> +	writel(BIT(bit_pos),
> +		ks_pcie->va_app_base + MSI0_IRQ_ENABLE_CLR + (reg_offset << 4));
> +}
> +
> +static void ks_dw_pcie_msi_irq_mask(struct irq_data *d)
> +{
> +	struct keystone_pcie *ks_pcie;
> +	unsigned int irq = d->irq;
> +	struct msi_desc *msi;
> +	struct pcie_port *pp;
> +	u32 offset;
> +
> +	msi = irq_get_msi_desc(irq);
> +	pp = sys_to_pcie(msi->dev->bus->sysdata);
> +	ks_pcie = to_keystone_pcie(pp);
> +	offset = irq - irq_linear_revmap(pp->irq_domain, 0);
> +
> +	/* mask the end point if PVM implemented */
> +	if (IS_ENABLED(CONFIG_PCI_MSI)) {
> +		if (msi->msi_attrib.maskbit)
> +			mask_msi_irq(d);
> +	}
> +
> +	ks_dw_pcie_msi_clear_irq(pp, offset);
> +}
> +
> +static void ks_dw_pcie_msi_irq_unmask(struct irq_data *d)
> +{
> +	struct keystone_pcie *ks_pcie;
> +	unsigned int irq = d->irq;
> +	struct msi_desc *msi;
> +	struct pcie_port *pp;
> +	u32 offset;
> +
> +	msi = irq_get_msi_desc(irq);
> +	pp = sys_to_pcie(msi->dev->bus->sysdata);
> +	ks_pcie = to_keystone_pcie(pp);
> +	offset = irq - irq_linear_revmap(pp->irq_domain, 0);
> +
> +	/* mask the end point if PVM implemented */
> +	if (IS_ENABLED(CONFIG_PCI_MSI)) {
> +		if (msi->msi_attrib.maskbit)
> +			unmask_msi_irq(d);
> +	}
> +
> +	ks_dw_pcie_msi_set_irq(pp, offset);
> +}
> +
> +static struct irq_chip ks_dw_pcie_msi_irq_chip = {
> +	.name = "Keystone-PCIe-MSI-IRQ",
> +	.irq_ack = ks_dw_pcie_msi_irq_ack,
> +	.irq_mask = ks_dw_pcie_msi_irq_mask,
> +	.irq_unmask = ks_dw_pcie_msi_irq_unmask,
> +};
> +
> +static int ks_dw_pcie_msi_map(struct irq_domain *domain, unsigned int irq,
> +			irq_hw_number_t hwirq)
> +{
> +	irq_set_chip_and_handler(irq, &ks_dw_pcie_msi_irq_chip,
> +				 handle_level_irq);
> +	irq_set_chip_data(irq, domain->host_data);
> +	set_irq_flags(irq, IRQF_VALID);
> +
> +	return 0;
> +}
> +
> +const struct irq_domain_ops ks_dw_pcie_msi_domain_ops = {
> +	.map = ks_dw_pcie_msi_map,
> +};
> +
> +void ks_dw_pcie_enable_legacy_irqs(struct keystone_pcie *ks_pcie)
> +{
> +	int i;
> +
> +	for (i = 0; i < MAX_LEGACY_IRQS; i++)
> +		writel(0x1, ks_pcie->va_app_base + IRQ_ENABLE_SET + (i << 4));
> +}
> +
> +void ks_dw_pcie_handle_legacy_irq(struct keystone_pcie *ks_pcie, int offset)
> +{
> +	struct pcie_port *pp = &ks_pcie->pp;
> +	u32 pending;
> +	int virq;
> +
> +	pending = readl(ks_pcie->va_app_base + IRQ_STATUS + (offset << 4));
> +
> +	if (BIT(0) & pending) {
> +		virq = irq_linear_revmap(ks_pcie->legacy_irq_domain, offset);
> +		dev_dbg(pp->dev,
> +			": irq: irq_offset %d, virq %d\n", offset, virq);
> +		generic_handle_irq(virq);
> +	}
> +
> +	/* EOI the INTx interrupt */
> +	writel(offset, ks_pcie->va_app_base + IRQ_EOI);
> +}
> +
> +static void ks_dw_pcie_ack_legacy_irq(struct irq_data *d)
> +{
> +}
> +
> +static void ks_dw_pcie_mask_legacy_irq(struct irq_data *d)
> +{
> +}
> +
> +static void ks_dw_pcie_unmask_legacy_irq(struct irq_data *d)
> +{
> +}
> +
> +static struct irq_chip ks_dw_pcie_legacy_irq_chip = {
> +	.name = "Keystone-PCI-Legacy-IRQ",
> +	.irq_ack = ks_dw_pcie_ack_legacy_irq,
> +	.irq_mask = ks_dw_pcie_mask_legacy_irq,
> +	.irq_unmask = ks_dw_pcie_unmask_legacy_irq,
> +};
> +
> +static int ks_dw_pcie_init_legacy_irq_map(struct irq_domain *d,
> +				unsigned int irq, irq_hw_number_t hw_irq)
> +{
> +	irq_set_chip_and_handler(irq, &ks_dw_pcie_legacy_irq_chip,
> +				handle_level_irq);
> +	irq_set_chip_data(irq, d->host_data);
> +	set_irq_flags(irq, IRQF_VALID);
> +
> +	return 0;
> +}
> +
> +static const struct irq_domain_ops ks_dw_pcie_legacy_irq_domian_ops = {
> +	.map = ks_dw_pcie_init_legacy_irq_map,
> +	.xlate = irq_domain_xlate_onetwocell,
> +};
> +
> +/**
> + * ks_dw_pcie_set_dbi_mode() - Set DBI mode to access overlaid BAR mask registers
> + *
> + * Since modification of dbi_cs2 involves different clock domain, read the
> + * status back to ensure the transition is complete.
> + */
> +static inline void ks_dw_pcie_set_dbi_mode(void __iomem *reg_virt)

Seems dubious to mark a function that accesses CSRs as "inline".

> +{
> +	u32 val;
> +
> +	writel(DBI_CS2_EN_VAL | readl(reg_virt + CMD_STATUS),
> +		     reg_virt + CMD_STATUS);
> +
> +	do {
> +		val = readl(reg_virt + CMD_STATUS);
> +	} while (!(val & DBI_CS2_EN_VAL));
> +}
> +
> +/**
> + * ks_dw_pcie_clear_dbi_mode() - Disable DBI mode
> + *
> + * Since modification of dbi_cs2 involves different clock domain, read the
> + * status back to ensure the transition is complete.
> + */
> +static inline void ks_dw_pcie_clear_dbi_mode(void __iomem *reg_virt)

Ditto.

> +{
> +	u32 val;
> +
> +	writel(~DBI_CS2_EN_VAL & readl(reg_virt + CMD_STATUS),
> +		     reg_virt + CMD_STATUS);
> +
> +	do {
> +		val = readl(reg_virt + CMD_STATUS);
> +	} while (val & DBI_CS2_EN_VAL);
> +}
> +
> +void ks_dw_pcie_setup_rc_app_regs(struct keystone_pcie *ks_pcie)
> +{
> +	struct pcie_port *pp = &ks_pcie->pp;
> +	u32 start = pp->mem.start, end = pp->mem.end;
> +	int i, tr_size;
> +
> +	/* disable BARS for inbound access */
> +	ks_dw_pcie_set_dbi_mode(ks_pcie->va_app_base);
> +	writel(0, pp->dbi_base + PCI_BASE_ADDRESS_0);
> +	writel(0, pp->dbi_base + PCI_BASE_ADDRESS_1);
> +	ks_dw_pcie_clear_dbi_mode(ks_pcie->va_app_base);
> +
> +	/* Set outbound translation size per window division */
> +	writel(CFG_PCIM_WIN_SZ_IDX & 0x7, ks_pcie->va_app_base + OB_SIZE);
> +
> +	tr_size = (1 << (CFG_PCIM_WIN_SZ_IDX & 0x7)) * SZ_1M;
> +
> +	/* Using Direct 1:1 mapping of RC <-> PCI memory space */
> +	for (i = 0; (i < CFG_PCIM_WIN_CNT) && (start < end); i++) {
> +		writel(start | 1, ks_pcie->va_app_base + OB_OFFSET_INDEX(i));
> +		writel(0, ks_pcie->va_app_base + OB_OFFSET_HI(i));
> +		start += tr_size;
> +	}
> +
> +	/* Enable OB translation */
> +	writel(OB_XLAT_EN_VAL | readl(ks_pcie->va_app_base + CMD_STATUS),
> +		ks_pcie->va_app_base + CMD_STATUS);
> +}
> +
> +/**
> + * ks_pcie_setup_config_addr() - Set up configuration space address for a
> + * device
> + *
> + * @ks_pcie: ptr to keystone_pcie structure
> + * @bus: Bus number the device is residing on
> + * @device: Device number
> + * @function: Function number in device
> + *
> + * Forms and returns the address of configuration space mapped in PCIESS
> + * address space 0. Also configures CFG_SETUP for remote configuration space
> + * access.
> + *
> + * The address space has two regions to access configuration - local and remote.
> + * We access local region for bus 0 (as RC is attached on bus 0) and remote
> + * region for others with TYPE 1 access when bus > 1. As for device on bus = 1,
> + * we will do TYPE 0 access as it will be on our secondary bus (logical).
> + * CFG_SETUP is needed only for remote configuration access.
> + */
> +static inline void __iomem *
> +ks_pcie_setup_config_addr(struct keystone_pcie *ks_pcie, u8 bus, u8 device,
> +			  u8 function)

Inconsistent formatting (function name is normally on the same line as
its type).  "inline" probably pointless, maybe the name could be shortened,
too, e.g., "ks_pcie_cfg_addr".

Consider passing devfn in, and using PCI_SLOT() and PCI_FUNC() here instead
of in both callers.

> +{
> +	struct pcie_port *pp = &ks_pcie->pp;
> +	u32 regval;
> +
> +	if (bus == 0)
> +		return pp->dbi_base;
> +
> +	regval = (bus << 16) | (device << 8) | function;
> +	/*
> +	 * Since Bus#1 will be a virtual bus, we need to have TYPE0
> +	 * access only.
> +	 * TYPE 1
> +	 */
> +	if (bus != 1)
> +		regval |= BIT(24);
> +
> +	writel(regval, ks_pcie->va_app_base + CFG_SETUP);
> +
> +	return pp->dbi_base + SPACE0_REMOTE_CFG_OFFSET;
> +}
> +
> +int ks_dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
> +		unsigned int devfn, int where, int size, u32 *val)
> +{
> +	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
> +	u8 bus_num = bus->number;
> +	void __iomem *addr;
> +	int ret;
> +
> +	addr = ks_pcie_setup_config_addr(ks_pcie, bus_num, PCI_SLOT(devfn),
> +					 PCI_FUNC(devfn));
> +
> +	ret = dw_pcie_cfg_read(addr + (where & ~0x3), where, size, val);
> +
> +	return ret;
> +}
> +
> +int ks_dw_pcie_wr_other_conf(struct pcie_port *pp,
> +		struct pci_bus *bus, unsigned int devfn, int where,
> +		int size, u32 val)
> +{
> +	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
> +	u8 bus_num = bus->number;
> +	void __iomem *addr;
> +
> +	addr = ks_pcie_setup_config_addr(ks_pcie, bus_num, PCI_SLOT(devfn),
> +					 PCI_FUNC(devfn));
> +	return dw_pcie_cfg_write(addr + (where & ~0x3), where, size, val);
> +}
> +
> +/**
> + * ks_dw_pcie_set_ib_access() - Setup inbound access
> + *
> + * Configure BAR0 for inbound access. BAR0 is set up in h/w to have
> + * access to PCIESS application register space and just needs to set up
> + * inbound address (mainly used for MSI).
> + */
> +static void ks_dw_pcie_set_ib_access(struct keystone_pcie *ks_pcie)
> +{
> +	struct pcie_port *pp = &ks_pcie->pp;
> +
> +	/* Configure and set up BAR0 */
> +	ks_dw_pcie_set_dbi_mode(ks_pcie->va_app_base);
> +
> +	/* Enable BAR0 */
> +	writel(1, pp->dbi_base + PCI_BASE_ADDRESS_0);
> +	writel(SZ_4K - 1, pp->dbi_base + PCI_BASE_ADDRESS_0);
> +
> +	ks_dw_pcie_clear_dbi_mode(ks_pcie->va_app_base);

Add a blank line here.

> +	 /*
> +	  * For BAR0, just setting bus address for inbound writes (MSI) should
> +	  * be sufficient. Use physical address to avoid any conflicts.
> +	  */
> +	writel(ks_pcie->app.start, pp->dbi_base + PCI_BASE_ADDRESS_0);
> +}
> +
> +/**
> + * ks_dw_pcie_v3_65_scan_bus() - common function to scan bus
> + *
> + * common functin to scan v3_65 dw based pci bus. This also sets inbound access

s/functin/function/

> + * after scan.
> + */
> +static struct pci_bus *ks_dw_pcie_v3_65_scan_bus(int nr,
> +						 struct pci_sys_data *sys)
> +{
> +	struct pcie_port *pp = sys_to_pcie(sys);
> +	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
> +	struct pci_bus *bus;
> +
> +	bus = dw_pcie_scan_bus(nr, sys);
> +	if (bus)
> +		ks_dw_pcie_set_ib_access(ks_pcie);
> +
> +	return bus;
> +}
> +
> +/**
> + * ks_dw_pcie_link_up() - Check if link up
> + *
> + */
> +int ks_dw_pcie_link_up(struct pcie_port *pp)
> +{
> +	u32 val = readl(pp->dbi_base + DEBUG0);
> +
> +	return (val & LTSSM_STATE_MASK) == LTSSM_STATE_L0;
> +}
> +
> +void ks_dw_pcie_initiate_link_train(struct keystone_pcie *ks_pcie)
> +{
> +	u32 val;
> +
> +	/* Initiate Link Training.  */
> +	val = readl(ks_pcie->va_app_base + CMD_STATUS);
> +	writel(LTSSM_EN_VAL | val,  ks_pcie->va_app_base + CMD_STATUS);
> +}
> +
> +static struct hw_pci ks_dw_pcie_v3_65_hw = {
> +	.nr_controllers	= 1,
> +	.setup		= dw_pcie_setup,
> +	.scan		= ks_dw_pcie_v3_65_scan_bus,
> +	.add_bus	= dw_pcie_add_bus,
> +	.map_irq	= dw_pcie_map_irq,
> +};
> +
> +/**
> + * ks_dw_pcie_host_init() - initialize host for v3_65 dw hardware
> + *
> + * It ioremap the register resources, initialize legacy irq domain
> + * and then call dw_pcie_v3_65_host_init() API to intialize the Keystone
> + * PCI host controller.
> + *
> + */
> +int __init ks_dw_pcie_host_init(struct keystone_pcie *ks_pcie,
> +				struct device_node *msi_intc_np)

Called from add_pcie_port(), which is not __init.  But add_pcie_port() is
only called from ks_pcie_probe(), which *is* __init.  Looks like maybe
add_pcie_port() should be __init as well?

> +{
> +	struct pcie_port *pp = &ks_pcie->pp;
> +	struct platform_device *pdev = to_platform_device(pp->dev);
> +	struct resource *res;
> +
> +	/* index 0 is the config reg. space address */
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	pp->dbi_base = devm_ioremap_resource(pp->dev, res);
> +	if (IS_ERR(pp->dbi_base))
> +		return PTR_ERR(pp->dbi_base);
> +
> +	/* index 1 is the application reg. space address */
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> +	ks_pcie->app = *res;
> +	ks_pcie->va_app_base = devm_ioremap_resource(pp->dev, res);
> +	if (IS_ERR(ks_pcie->va_app_base))
> +		return PTR_ERR(ks_pcie->va_app_base);
> +
> +	/* create legacy irq domain */
> +	ks_pcie->legacy_irq_domain =
> +			irq_domain_add_linear(ks_pcie->legacy_intc_np,
> +					MAX_LEGACY_IRQS,
> +					&ks_dw_pcie_legacy_irq_domian_ops,
> +					NULL);
> +	if (!ks_pcie->legacy_irq_domain) {
> +		dev_err(pp->dev, "Failed to add irq domain for legacy irqs\n");
> +		return -EINVAL;
> +	}
> +
> +	return dw_pcie_v3_65_host_init(pp, &ks_dw_pcie_v3_65_hw, msi_intc_np,
> +					&ks_dw_pcie_msi_domain_ops);
> +}
> diff --git a/drivers/pci/host/pci-keystone.c b/drivers/pci/host/pci-keystone.c
> new file mode 100644
> index 0000000..e1cf671
> --- /dev/null
> +++ b/drivers/pci/host/pci-keystone.c
> @@ -0,0 +1,381 @@
> +/*
> + * PCIe host controller driver for Texas Instruments Keystone SoCs
> + *
> + * Copyright (C) 2013-2014 Texas Instruments., Ltd.
> + *		http://www.ti.com
> + *
> + * Author: Murali Karicheri <m-karicheri2@xxxxxx>
> + * Implementation based on pci-exynos.c and pcie-designware.c
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/irqchip/chained_irq.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/irqdomain.h>
> +#include <linux/module.h>
> +#include <linux/msi.h>
> +#include <linux/of_irq.h>
> +#include <linux/of.h>
> +#include <linux/of_pci.h>
> +#include <linux/platform_device.h>
> +#include <linux/phy/phy.h>
> +#include <linux/resource.h>
> +#include <linux/signal.h>
> +
> +#include "pcie-designware.h"
> +#include "pci-keystone.h"
> +
> +#define DRIVER_NAME	"keystone-pcie"
> +
> +/* driver specific constants */
> +#define MAX_MSI_HOST_IRQS		8
> +#define MAX_LEGACY_HOST_IRQS		4
> +
> +/* RC mode settings */
> +#define PCIE_RC_MODE		(BIT(2))
> +#define PCIE_MODE_MASK		(BIT(1) | BIT(2))
> +
> +/* DEV_STAT_CTRL */
> +#define PCIE_CAP_BASE       0x70
> +
> +#define to_keystone_pcie(x)	container_of(x, struct keystone_pcie, pp)
> +
> +static int ks_pcie_establish_link(struct keystone_pcie *ks_pcie)
> +{
> +	struct pcie_port *pp = &ks_pcie->pp;
> +	int count = 200;
> +
> +	dw_pcie_setup_rc(pp);
> +	if (ks_pcie->link_train)
> +		ks_dw_pcie_initiate_link_train(ks_pcie);
> +
> +	/* check if the link is up or not */
> +	while (!dw_pcie_link_up(pp)) {
> +		usleep_range(100, 1000);
> +		if (--count)
> +			continue;
> +		dev_err(pp->dev, "phy link never came up\n");
> +		return -EINVAL;
> +	}
> +
> +	return 0;
> +}
> +
> +static void ks_pcie_msi_irq_handler(unsigned int irq, struct irq_desc *desc)
> +{
> +	struct keystone_pcie *ks_pcie = irq_desc_get_handler_data(desc);
> +	u32 offset = irq - ks_pcie->msi_host_irqs[0];
> +	struct pcie_port *pp = &ks_pcie->pp;
> +	struct irq_chip *chip = irq_desc_get_chip(desc);
> +
> +	dev_dbg(pp->dev, "ks_pci_msi_irq_handler, irq %d\n", irq);
> +
> +	/*
> +	 * The chained irq handler installation would have replaced normal
> +	 * interrupt driver handler so we need to take care of mask/unmask and
> +	 * ack operation.
> +	 */
> +	chained_irq_enter(chip, desc);
> +	ks_dw_pcie_handle_msi_irq(ks_pcie, offset);
> +	chained_irq_exit(chip, desc);
> +}
> +
> +/**
> + * ks_pcie_legacy_irq_handler() - Handle legacy interrupt
> + * @irq: IRQ line for legacy interrupts
> + * @desc: Pointer to irq descriptor
> + *
> + * Traverse through pending legacy interrupts and invoke handler for each. Also
> + * takes care of interrupt controller level mask/ack operation.
> + */
> +static void ks_pcie_legacy_irq_handler(unsigned int irq, struct irq_desc *desc)
> +{
> +	struct keystone_pcie *ks_pcie = irq_desc_get_handler_data(desc);
> +	struct pcie_port *pp = &ks_pcie->pp;
> +	u32 irq_offset = irq - ks_pcie->legacy_host_irqs[0];
> +	struct irq_chip *chip = irq_desc_get_chip(desc);
> +
> +	dev_dbg(pp->dev, ": Handling legacy irq %d\n", irq);
> +
> +	/*
> +	 * The chained irq handler installation would have replaced normal
> +	 * interrupt driver handler so we need to take care of mask/unmask and
> +	 * ack operation.
> +	 */
> +	chained_irq_enter(chip, desc);
> +	ks_dw_pcie_handle_legacy_irq(ks_pcie, irq_offset);
> +	chained_irq_exit(chip, desc);
> +}
> +
> +static int ks_pcie_get_irq_controller_info(struct keystone_pcie *ks_pcie,
> +					   char *controller, int *num_irqs)
> +{
> +	int temp, max_host_irqs, legacy = 1, *host_irqs, ret = -EINVAL;
> +	struct device *dev = ks_pcie->pp.dev;
> +	struct device_node *np_pcie = dev->of_node, **np_temp;
> +
> +	if (!strcmp(controller, "msi-interrupt-controller"))
> +		legacy = 0;
> +
> +	if (legacy) {
> +		np_temp = &ks_pcie->legacy_intc_np;
> +		max_host_irqs = MAX_LEGACY_HOST_IRQS;
> +		host_irqs = &ks_pcie->legacy_host_irqs[0];
> +	} else {
> +		np_temp = &ks_pcie->msi_intc_np;
> +		max_host_irqs = MAX_MSI_HOST_IRQS;
> +		host_irqs =  &ks_pcie->msi_host_irqs[0];
> +	}
> +
> +	/* interrupt controller is in a child node */
> +	*np_temp = of_find_node_by_name(np_pcie, controller);
> +	if (!(*np_temp)) {
> +		dev_err(dev, "Node for %s is absent\n", controller);
> +		goto out;
> +	}
> +	temp = of_irq_count(*np_temp);
> +	if (!temp)
> +		goto out;
> +	if (temp > max_host_irqs)
> +		dev_warn(dev, "Too many %s interrupts defined %u\n",
> +			(legacy ? "legacy" : "MSI"), temp);
> +
> +	/*
> +	 * support upto max_host_irqs. In dt from index 0 to 3 (legacy) or 0 to
> +	 * 7 (MSI)
> +	 */
> +	for (temp = 0; temp < max_host_irqs; temp++) {
> +		host_irqs[temp] = irq_of_parse_and_map(*np_temp, temp);
> +		if (host_irqs[temp] < 0)
> +			break;
> +	}
> +	if (temp) {
> +		*num_irqs = temp;
> +		ret = 0;
> +	}
> +out:
> +	return ret;
> +}
> +
> +static void ks_pcie_setup_interrupts(struct keystone_pcie *ks_pcie)
> +{
> +	int i;
> +
> +	/* Legacy IRQ */
> +	for (i = 0; i < ks_pcie->num_legacy_host_irqs; i++) {
> +		irq_set_handler_data(ks_pcie->legacy_host_irqs[i], ks_pcie);
> +		irq_set_chained_handler(ks_pcie->legacy_host_irqs[i],
> +					ks_pcie_legacy_irq_handler);
> +	}
> +	ks_dw_pcie_enable_legacy_irqs(ks_pcie);
> +
> +	/* MSI IRQ */
> +	if (IS_ENABLED(CONFIG_PCI_MSI)) {
> +		for (i = 0; i < ks_pcie->num_msi_host_irqs; i++) {
> +			irq_set_chained_handler(ks_pcie->msi_host_irqs[i],
> +						ks_pcie_msi_irq_handler);
> +			irq_set_handler_data(ks_pcie->msi_host_irqs[i],
> +					     ks_pcie);
> +		}
> +	}
> +}
> +
> +/*
> + * When a PCI device does not exist during config cycles, keystone host gets a
> + * bus error instead of returning 0xffffffff. This handler always returns 0
> + * for this kind of faults.
> + */
> +static int
> +keystone_pcie_fault(unsigned long addr, unsigned int fsr,
> +		struct pt_regs *regs)

"static int keystone_pcie_fault(..." (on one line).

> +{
> +	unsigned long instr = *(unsigned long *) instruction_pointer(regs);
> +
> +	if ((instr & 0x0e100090) == 0x00100090) {
> +		int reg = (instr >> 12) & 15;
> +
> +		regs->uregs[reg] = -1;
> +		regs->ARM_pc += 4;
> +	}
> +
> +	return 0;
> +}
> +
> +static void __init ks_pcie_host_init(struct pcie_port *pp)
> +{
> +	u32 vendor_device_id, val;
> +	struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
> +
> +	ks_pcie_establish_link(ks_pcie);
> +	ks_dw_pcie_setup_rc_app_regs(ks_pcie);
> +	ks_pcie_setup_interrupts(ks_pcie);
> +	writew(PCI_IO_RANGE_TYPE_32 | (PCI_IO_RANGE_TYPE_32 << 8),
> +			pp->dbi_base + PCI_IO_BASE);
> +
> +	/* update the Vendor ID */
> +	vendor_device_id = readl(ks_pcie->va_reg_pciid);
> +	writew((vendor_device_id >> 16), pp->dbi_base + PCI_DEVICE_ID);
> +
> +	/* update the DEV_STAT_CTRL to publish right mrrs */
> +	val = readl(pp->dbi_base + PCIE_CAP_BASE + PCI_EXP_DEVCTL);
> +	val &= ~PCI_EXP_DEVCTL_READRQ;
> +	/* set the mrrs to 256 bytes */
> +	val |= BIT(12);
> +	writel(val, pp->dbi_base + PCIE_CAP_BASE + PCI_EXP_DEVCTL);
> +
> +	/*
> +	 * PCIe access errors that result into OCP errors are caught by ARM as
> +	 * "External aborts"
> +	 */
> +	hook_fault_code(17, keystone_pcie_fault, SIGBUS, 0,
> +			"Asynchronous external abort");
> +}
> +
> +static struct pcie_host_ops keystone_pcie_host_ops = {
> +	.rd_other_conf = ks_dw_pcie_rd_other_conf,
> +	.wr_other_conf = ks_dw_pcie_wr_other_conf,
> +	.link_up = ks_dw_pcie_link_up,
> +	.host_init = ks_pcie_host_init,
> +	.msi_set_irq = ks_dw_pcie_msi_set_irq,
> +	.msi_clear_irq = ks_dw_pcie_msi_clear_irq,
> +	.get_msi_data = ks_dw_pcie_get_msi_data,
> +};
> +
> +static int add_pcie_port(struct keystone_pcie *ks_pcie,
> +			 struct platform_device *pdev)
> +{
> +	struct pcie_port *pp = &ks_pcie->pp;
> +	int ret;
> +
> +	ret = ks_pcie_get_irq_controller_info(ks_pcie,
> +					"legacy-interrupt-controller",
> +					&ks_pcie->num_legacy_host_irqs);
> +	if (ret)
> +		return ret;
> +
> +	if (IS_ENABLED(CONFIG_PCI_MSI)) {
> +		ret = ks_pcie_get_irq_controller_info(ks_pcie,
> +						"msi-interrupt-controller",
> +						&ks_pcie->num_msi_host_irqs);
> +		if (ret)
> +			return ret;
> +	}
> +
> +	pp->root_bus_nr = -1;
> +	pp->ops = &keystone_pcie_host_ops;
> +	ret = ks_dw_pcie_host_init(ks_pcie, ks_pcie->msi_intc_np);
> +	if (ret) {
> +		dev_err(&pdev->dev, "failed to initialize host\n");
> +		return ret;
> +	}
> +
> +	return ret;
> +}
> +
> +static const struct of_device_id ks_pcie_of_match[] = {
> +	{
> +		.type = "pci",
> +		.compatible = "ti,keystone-pcie",
> +	},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, ks_pcie_of_match);
> +
> +static int __exit ks_pcie_remove(struct platform_device *pdev)
> +{
> +	struct keystone_pcie *ks_pcie = platform_get_drvdata(pdev);
> +
> +	clk_disable_unprepare(ks_pcie->clk);
> +
> +	return 0;
> +}
> +
> +static int __init ks_pcie_probe(struct platform_device *pdev)
> +{
> +	struct device_node *np = pdev->dev.of_node;
> +	struct device *dev = &pdev->dev;
> +	struct keystone_pcie *ks_pcie;
> +	struct pcie_port *pp;
> +	struct resource *res;
> +	void __iomem *reg_p;
> +	struct phy *phy;
> +	int ret = 0;
> +	u32 val;
> +
> +	ks_pcie = devm_kzalloc(&pdev->dev, sizeof(*ks_pcie),
> +				GFP_KERNEL);
> +	if (!ks_pcie) {
> +		dev_err(dev, "no memory for keystone pcie\n");
> +		return -ENOMEM;
> +	}
> +	pp = &ks_pcie->pp;
> +
> +	/* initialize SerDes Phy if present */
> +	phy = devm_phy_get(dev, "pcie-phy");
> +	if (phy)
> +		ret = phy_init(phy);
> +
> +	/* index 2 is the devcfg register for RC mode settings */
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
> +	reg_p = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(reg_p))
> +		return PTR_ERR(reg_p);
> +
> +	/* enable RC mode in devcfg */
> +	val = readl(reg_p);
> +	val &= ~PCIE_MODE_MASK;
> +	val |= PCIE_RC_MODE;
> +	writel(val, reg_p);
> +
> +	/* index 3 is to read PCI DEVICE_ID */
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 3);
> +	reg_p = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(reg_p))
> +		return PTR_ERR(reg_p);
> +	ks_pcie->va_reg_pciid = reg_p;
> +
> +	/* check if we need to enable link training */
> +	ks_pcie->link_train =
> +		(of_get_property(np, "ti,enable-linktrain", NULL) != NULL);
> +
> +	pp->dev = dev;
> +	platform_set_drvdata(pdev, ks_pcie);
> +	ks_pcie->clk = devm_clk_get(dev, "pcie");
> +	if (IS_ERR(ks_pcie->clk)) {
> +		dev_err(dev, "Failed to get pcie rc clock\n");
> +		return PTR_ERR(ks_pcie->clk);
> +	}
> +	ret = clk_prepare_enable(ks_pcie->clk);
> +	if (ret)
> +		return ret;
> +
> +	ret = add_pcie_port(ks_pcie, pdev);
> +	if (ret < 0)
> +		goto fail_clk;
> +
> +	return 0;
> +fail_clk:
> +	clk_disable_unprepare(ks_pcie->clk);
> +
> +	return ret;
> +}
> +
> +static struct platform_driver ks_pcie_driver __refdata = {
> +	.probe  = ks_pcie_probe,
> +	.remove = __exit_p(ks_pcie_remove),
> +	.driver = {
> +		.name	= "keystone-pcie",
> +		.owner	= THIS_MODULE,
> +		.of_match_table = of_match_ptr(ks_pcie_of_match),
> +	},
> +};
> +
> +module_platform_driver(ks_pcie_driver);
> +
> +MODULE_AUTHOR("Murali Karicheri <m-karicheri2@xxxxxx>");
> +MODULE_DESCRIPTION("Keystone PCIe host controller driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/drivers/pci/host/pci-keystone.h b/drivers/pci/host/pci-keystone.h
> new file mode 100644
> index 0000000..b133f5c
> --- /dev/null
> +++ b/drivers/pci/host/pci-keystone.h
> @@ -0,0 +1,56 @@
> +/*
> + * Keystone PCI Controller's common includes
> + *
> + * Copyright (C) 2013-2014 Texas Instruments., Ltd.
> + *		http://www.ti.com
> + *
> + * Author: Murali Karicheri <m-karicheri2@xxxxxx>
> + *
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#define MAX_LEGACY_IRQS			4
> +#define MAX_MSI_HOST_IRQS		8
> +#define MAX_LEGACY_HOST_IRQS		4
> +
> +struct keystone_pcie {
> +	struct	clk		*clk;
> +	int			link_train;
> +	struct	pcie_port	pp;
> +	void __iomem		*va_reg_pciid;
> +
> +	int			num_legacy_host_irqs;
> +	int			legacy_host_irqs[MAX_LEGACY_HOST_IRQS];
> +	struct			device_node *legacy_intc_np;
> +
> +	int			num_msi_host_irqs;
> +	int			msi_host_irqs[MAX_MSI_HOST_IRQS];
> +	struct			device_node *msi_intc_np;
> +	struct irq_domain	*legacy_irq_domain;
> +
> +	/* Application register space */
> +	void __iomem		*va_app_base;
> +	struct resource		app;
> +};
> +
> +/* Keystone DW specific MSI controller APIs/definitions */
> +void ks_dw_pcie_handle_msi_irq(struct keystone_pcie *ks_pcie, int offset);
> +u32 ks_dw_pcie_get_msi_data(struct pcie_port *pp);
> +
> +/* Keystone specific PCI controller APIs */
> +void ks_dw_pcie_enable_legacy_irqs(struct keystone_pcie *ks_pcie);
> +void ks_dw_pcie_handle_legacy_irq(struct keystone_pcie *ks_pcie, int offset);
> +int  ks_dw_pcie_host_init(struct keystone_pcie *ks_pcie,
> +			struct device_node *msi_intc_np);
> +int ks_dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
> +		unsigned int devfn, int where, int size, u32 val);
> +int ks_dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
> +		unsigned int devfn, int where, int size, u32 *val);
> +void ks_dw_pcie_setup_rc_app_regs(struct keystone_pcie *ks_pcie);
> +int ks_dw_pcie_link_up(struct pcie_port *pp);
> +void ks_dw_pcie_initiate_link_train(struct keystone_pcie *ks_pcie);
> +void ks_dw_pcie_msi_set_irq(struct pcie_port *pp, int irq);
> +void ks_dw_pcie_msi_clear_irq(struct pcie_port *pp, int irq);
> -- 
> 1.7.9.5
> 
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux