From: Stefan Chulski <stefanc@xxxxxxxxxxx>
The PP2v23 hardware supports a feature allowing to double the
size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.
Signed-off-by: Stefan Chulski <stefanc@xxxxxxxxxxx>
Acked-by: Marcin Wojtas <mw@xxxxxxxxxxxx>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 8 ++++++
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 26 ++++++++++++++++++++
2 files changed, 34 insertions(+)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 0731dc7..9b525b60 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -324,6 +324,10 @@
#define MVPP2_BM_HIGH_THRESH_MASK 0x7f0000
#define MVPP2_BM_HIGH_THRESH_VALUE(val) ((val) << \
MVPP2_BM_HIGH_THRESH_OFFS)
+#define MVPP2_BM_BPPI_HIGH_THRESH 0x1E
+#define MVPP2_BM_BPPI_LOW_THRESH 0x1C
+#define MVPP23_BM_BPPI_HIGH_THRESH 0x34
+#define MVPP23_BM_BPPI_LOW_THRESH 0x28
#define MVPP2_BM_INTR_CAUSE_REG(pool) (0x6240 + ((pool) * 4))
#define MVPP2_BM_RELEASED_DELAY_MASK BIT(0)
#define MVPP2_BM_ALLOC_FAILED_MASK BIT(1)
@@ -352,6 +356,10 @@
#define MVPP2_OVERRUN_ETH_DROP 0x7000
#define MVPP2_CLS_ETH_DROP 0x7020
+#define MVPP22_BM_POOL_BASE_ADDR_HIGH_REG 0x6310
+#define MVPP22_BM_POOL_BASE_ADDR_HIGH_MASK 0xff
+#define MVPP23_BM_8POOL_MODE BIT(8)
+
/* Hit counters registers */
#define MVPP2_CTRS_IDX 0x7040
#define MVPP22_CTRS_TX_CTR(port, txq) ((txq) | ((port) << 3) | BIT(7))
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 90c9265..9226d2f 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -423,6 +423,19 @@ static int mvpp2_bm_pool_create(struct device *dev, struct mvpp2 *priv,
val = mvpp2_read(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id));
val |= MVPP2_BM_START_MASK;
+
+ val &= ~MVPP2_BM_LOW_THRESH_MASK;
+ val &= ~MVPP2_BM_HIGH_THRESH_MASK;
+
+ /* Set 8 Pools BPPI threshold for MVPP23 */
+ if (priv->hw_version == MVPP23) {
+ val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP23_BM_BPPI_LOW_THRESH);
+ val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP23_BM_BPPI_HIGH_THRESH);
+ } else {
+ val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP2_BM_BPPI_LOW_THRESH);
+ val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP2_BM_BPPI_HIGH_THRESH);
+ }
+
mvpp2_write(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id), val);
bm_pool->size = size;
@@ -591,6 +604,16 @@ static int mvpp2_bm_pools_init(struct device *dev, struct mvpp2 *priv)
return err;
}
+/* Routine enable PPv23 8 pool mode */
+static void mvpp23_bm_set_8pool_mode(struct mvpp2 *priv)
+{
+ int val;
+
+ val = mvpp2_read(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG);
+ val |= MVPP23_BM_8POOL_MODE;
+ mvpp2_write(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG, val);
+}
+
static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
{
enum dma_data_direction dma_dir = DMA_FROM_DEVICE;
@@ -644,6 +667,9 @@ static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
if (!priv->bm_pools)
return -ENOMEM;
+ if (priv->hw_version == MVPP23)
+ mvpp23_bm_set_8pool_mode(priv);
+
err = mvpp2_bm_pools_init(dev, priv);
if (err < 0)
return err;
--
1.9.1
