On Fri, Feb 05, 2021 at 11:34:14AM +0800, Kyle Tso wrote: > Add bindings of VDO properties of USB PD SVDM so that they can be > used in device tree. > > Signed-off-by: Kyle Tso <kyletso@xxxxxxxxxx> > --- > Changes since v5: > - no change > > .../bindings/connector/usb-connector.yaml | 11 + > include/dt-bindings/usb/pd.h | 311 +++++++++++++++++- > 2 files changed, 321 insertions(+), 1 deletion(-) > > diff --git a/Documentation/devicetree/bindings/connector/usb-connector.yaml b/Documentation/devicetree/bindings/connector/usb-connector.yaml > index 4286ed767a0a..d385026944ec 100644 > --- a/Documentation/devicetree/bindings/connector/usb-connector.yaml > +++ b/Documentation/devicetree/bindings/connector/usb-connector.yaml > @@ -137,6 +137,17 @@ properties: > maxItems: 7 > $ref: /schemas/types.yaml#/definitions/uint32-array > > + sink-vdos: > + description: An array of u32 with each entry (VDM Objects) providing additional information VDO stands for 'VDM Objects' and VDM stands for ??? Other than that, Reviewed-by: Rob Herring <robh@xxxxxxxxxx> > + corresponding to the product, the detailed bit definitions and the order of each VDO can be > + found in "USB Power Delivery Specification Revision 3.0, Version 2.0 + ECNs 2020-12-10" > + chapter 6.4.4.3.1 Discover Identity. User can specify the VDO array via > + VDO_IDH/_CERT/_PRODUCT/_UFP/_DFP/_PCABLE/_ACABLE(1/2)/_VPD() defined in > + dt-bindings/usb/pd.h. > + minItems: 3 > + maxItems: 6 > + $ref: /schemas/types.yaml#/definitions/uint32-array > + > op-sink-microwatt: > description: Sink required operating power in microwatt, if source can't > offer the power, Capability Mismatch is set. Required for power sink and > diff --git a/include/dt-bindings/usb/pd.h b/include/dt-bindings/usb/pd.h > index 0352893697f0..fef3ef65967f 100644 > --- a/include/dt-bindings/usb/pd.h > +++ b/include/dt-bindings/usb/pd.h > @@ -93,4 +93,313 @@ > #define FRS_DEFAULT_POWER 1 > #define FRS_5V_1P5A 2 > #define FRS_5V_3A 3 > - #endif /* __DT_POWER_DELIVERY_H */ > + > +/* > + * SVDM Identity Header > + * -------------------- > + * <31> :: data capable as a USB host > + * <30> :: data capable as a USB device > + * <29:27> :: product type (UFP / Cable / VPD) > + * <26> :: modal operation supported (1b == yes) > + * <25:23> :: product type (DFP) (SVDM version 2.0+ only; set to zero in version 1.0) > + * <22:21> :: connector type (SVDM version 2.0+ only; set to zero in version 1.0) > + * <20:16> :: Reserved, Shall be set to zero > + * <15:0> :: USB-IF assigned VID for this cable vendor > + */ > +/* SOP Product Type (UFP) */ > +#define IDH_PTYPE_NOT_UFP 0 > +#define IDH_PTYPE_HUB 1 > +#define IDH_PTYPE_PERIPH 2 > +#define IDH_PTYPE_PSD 3 > +#define IDH_PTYPE_AMA 5 > + > +/* SOP' Product Type (Cable Plug / VPD) */ > +#define IDH_PTYPE_NOT_CABLE 0 > +#define IDH_PTYPE_PCABLE 3 > +#define IDH_PTYPE_ACABLE 4 > +#define IDH_PTYPE_VPD 6 > + > +/* SOP Product Type (DFP) */ > +#define IDH_PTYPE_NOT_DFP 0 > +#define IDH_PTYPE_DFP_HUB 1 > +#define IDH_PTYPE_DFP_HOST 2 > +#define IDH_PTYPE_DFP_PB 3 > + > +#define VDO_IDH(usbh, usbd, ufp_cable, is_modal, dfp, conn, vid) \ > + ((usbh) << 31 | (usbd) << 30 | ((ufp_cable) & 0x7) << 27 \ > + | (is_modal) << 26 | ((dfp) & 0x7) << 23 | ((conn) & 0x3) << 21 \ > + | ((vid) & 0xffff)) > + > +/* > + * Cert Stat VDO > + * ------------- > + * <31:0> : USB-IF assigned XID for this cable > + */ > +#define VDO_CERT(xid) ((xid) & 0xffffffff) > + > +/* > + * Product VDO > + * ----------- > + * <31:16> : USB Product ID > + * <15:0> : USB bcdDevice > + */ > +#define VDO_PRODUCT(pid, bcd) (((pid) & 0xffff) << 16 | ((bcd) & 0xffff)) > + > +/* > + * UFP VDO (PD Revision 3.0+ only) > + * -------- > + * <31:29> :: UFP VDO version > + * <28> :: Reserved > + * <27:24> :: Device capability > + * <23:22> :: Connector type (10b == receptacle, 11b == captive plug) > + * <21:11> :: Reserved > + * <10:8> :: Vconn power (AMA only) > + * <7> :: Vconn required (AMA only, 0b == no, 1b == yes) > + * <6> :: Vbus required (AMA only, 0b == yes, 1b == no) > + * <5:3> :: Alternate modes > + * <2:0> :: USB highest speed > + */ > +/* UFP VDO Version */ > +#define UFP_VDO_VER1_2 2 > + > +/* Device Capability */ > +#define DEV_USB2_CAPABLE BIT(0) > +#define DEV_USB2_BILLBOARD BIT(1) > +#define DEV_USB3_CAPABLE BIT(2) > +#define DEV_USB4_CAPABLE BIT(3) > + > +/* Connector Type */ > +#define UFP_RECEPTACLE 2 > +#define UFP_CAPTIVE 3 > + > +/* Vconn Power (AMA only, set to AMA_VCONN_NOT_REQ if Vconn is not required) */ > +#define AMA_VCONN_PWR_1W 0 > +#define AMA_VCONN_PWR_1W5 1 > +#define AMA_VCONN_PWR_2W 2 > +#define AMA_VCONN_PWR_3W 3 > +#define AMA_VCONN_PWR_4W 4 > +#define AMA_VCONN_PWR_5W 5 > +#define AMA_VCONN_PWR_6W 6 > + > +/* Vconn Required (AMA only) */ > +#define AMA_VCONN_NOT_REQ 0 > +#define AMA_VCONN_REQ 1 > + > +/* Vbus Required (AMA only) */ > +#define AMA_VBUS_REQ 0 > +#define AMA_VBUS_NOT_REQ 1 > + > +/* Alternate Modes */ > +#define UFP_ALTMODE_NOT_SUPP 0 > +#define UFP_ALTMODE_TBT3 BIT(0) > +#define UFP_ALTMODE_RECFG BIT(1) > +#define UFP_ALTMODE_NO_RECFG BIT(2) > + > +/* USB Highest Speed */ > +#define UFP_USB2_ONLY 0 > +#define UFP_USB32_GEN1 1 > +#define UFP_USB32_4_GEN2 2 > +#define UFP_USB4_GEN3 3 > + > +#define VDO_UFP(ver, cap, conn, vcpwr, vcr, vbr, alt, spd) \ > + (((ver) & 0x7) << 29 | ((cap) & 0xf) << 24 | ((conn) & 0x3) << 22 \ > + | ((vcpwr) & 0x7) << 8 | (vcr) << 7 | (vbr) << 6 | ((alt) & 0x7) << 3 \ > + | ((spd) & 0x7)) > + > +/* > + * DFP VDO (PD Revision 3.0+ only) > + * -------- > + * <31:29> :: DFP VDO version > + * <28:27> :: Reserved > + * <26:24> :: Host capability > + * <23:22> :: Connector type (10b == receptacle, 11b == captive plug) > + * <21:5> :: Reserved > + * <4:0> :: Port number > + */ > +#define DFP_VDO_VER1_1 1 > +#define HOST_USB2_CAPABLE BIT(0) > +#define HOST_USB3_CAPABLE BIT(1) > +#define HOST_USB4_CAPABLE BIT(2) > +#define DFP_RECEPTACLE 2 > +#define DFP_CAPTIVE 3 > + > +#define VDO_DFP(ver, cap, conn, pnum) \ > + (((ver) & 0x7) << 29 | ((cap) & 0x7) << 24 | ((conn) & 0x3) << 22 \ > + | ((pnum) & 0x1f)) > + > +/* > + * Passive Cable VDO > + * --------- > + * <31:28> :: Cable HW version > + * <27:24> :: Cable FW version > + * <23:21> :: VDO version > + * <20> :: Reserved, Shall be set to zero > + * <19:18> :: Type-C to Type-C/Captive (10b == C, 11b == Captive) > + * <17> :: Reserved, Shall be set to zero > + * <16:13> :: cable latency (0001 == <10ns(~1m length)) > + * <12:11> :: cable termination type (10b == Vconn not req, 01b == Vconn req) > + * <10:9> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V) > + * <8:7> :: Reserved, Shall be set to zero > + * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A) > + * <4:3> :: Reserved, Shall be set to zero > + * <2:0> :: USB highest speed > + * > + * Active Cable VDO 1 > + * --------- > + * <31:28> :: Cable HW version > + * <27:24> :: Cable FW version > + * <23:21> :: VDO version > + * <20> :: Reserved, Shall be set to zero > + * <19:18> :: Connector type (10b == C, 11b == Captive) > + * <17> :: Reserved, Shall be set to zero > + * <16:13> :: cable latency (0001 == <10ns(~1m length)) > + * <12:11> :: cable termination type (10b == one end active, 11b == both ends active VCONN req) > + * <10:9> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V) > + * <8> :: SBU supported (0b == supported, 1b == not supported) > + * <7> :: SBU type (0b == passive, 1b == active) > + * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A) > + * <4> :: Vbus through cable (0b == no, 1b == yes) > + * <3> :: SOP" controller present? (0b == no, 1b == yes) > + * <2:0> :: USB highest speed > + */ > +/* Cable VDO Version */ > +#define CABLE_VDO_VER1_0 0 > +#define CABLE_VDO_VER1_3 3 > + > +/* Connector Type */ > +#define CABLE_CTYPE 2 > +#define CABLE_CAPTIVE 3 > + > +/* Cable Latency */ > +#define CABLE_LATENCY_1M 1 > +#define CABLE_LATENCY_2M 2 > +#define CABLE_LATENCY_3M 3 > +#define CABLE_LATENCY_4M 4 > +#define CABLE_LATENCY_5M 5 > +#define CABLE_LATENCY_6M 6 > +#define CABLE_LATENCY_7M 7 > +#define CABLE_LATENCY_7M_PLUS 8 > + > +/* Cable Termination Type */ > +#define PCABLE_VCONN_NOT_REQ 0 > +#define PCABLE_VCONN_REQ 1 > +#define ACABLE_ONE_END 2 > +#define ACABLE_BOTH_END 3 > + > +/* Maximum Vbus Voltage */ > +#define CABLE_MAX_VBUS_20V 0 > +#define CABLE_MAX_VBUS_30V 1 > +#define CABLE_MAX_VBUS_40V 2 > +#define CABLE_MAX_VBUS_50V 3 > + > +/* Active Cable SBU Supported/Type */ > +#define ACABLE_SBU_SUPP 0 > +#define ACABLE_SBU_NOT_SUPP 1 > +#define ACABLE_SBU_PASSIVE 0 > +#define ACABLE_SBU_ACTIVE 1 > + > +/* Vbus Current Handling Capability */ > +#define CABLE_CURR_DEF 0 > +#define CABLE_CURR_3A 1 > +#define CABLE_CURR_5A 2 > + > +/* USB Highest Speed */ > +#define CABLE_USB2_ONLY 0 > +#define CABLE_USB32_GEN1 1 > +#define CABLE_USB32_4_GEN2 2 > +#define CABLE_USB4_GEN3 3 > + > +#define VDO_PCABLE(hw, fw, ver, conn, lat, term, vbm, cur, spd) \ > + (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21 \ > + | ((conn) & 0x3) << 18 | ((lat) & 0xf) << 13 | ((term) & 0x3) << 11 \ > + | ((vbm) & 0x3) << 9 | ((cur) & 0x3) << 5 | ((spd) & 0x7)) > +#define VDO_ACABLE1(hw, fw, ver, conn, lat, term, vbm, sbu, sbut, cur, vbt, sopp, spd) \ > + (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21 \ > + | ((conn) & 0x3) << 18 | ((lat) & 0xf) << 13 | ((term) & 0x3) << 11 \ > + | ((vbm) & 0x3) << 9 | (sbu) << 8 | (sbut) << 7 | ((cur) & 0x3) << 5 \ > + | (vbt) << 4 | (sopp) << 3 | ((spd) & 0x7)) > + > +/* > + * Active Cable VDO 2 > + * --------- > + * <31:24> :: Maximum operating temperature > + * <23:16> :: Shutdown temperature > + * <15> :: Reserved, Shall be set to zero > + * <14:12> :: U3/CLd power > + * <11> :: U3 to U0 transition mode (0b == direct, 1b == through U3S) > + * <10> :: Physical connection (0b == copper, 1b == optical) > + * <9> :: Active element (0b == redriver, 1b == retimer) > + * <8> :: USB4 supported (0b == yes, 1b == no) > + * <7:6> :: USB2 hub hops consumed > + * <5> :: USB2 supported (0b == yes, 1b == no) > + * <4> :: USB3.2 supported (0b == yes, 1b == no) > + * <3> :: USB lanes supported (0b == one lane, 1b == two lanes) > + * <2> :: Optically isolated active cable (0b == no, 1b == yes) > + * <1> :: Reserved, Shall be set to zero > + * <0> :: USB gen (0b == gen1, 1b == gen2+) > + */ > +/* U3/CLd Power*/ > +#define ACAB2_U3_CLD_10MW_PLUS 0 > +#define ACAB2_U3_CLD_10MW 1 > +#define ACAB2_U3_CLD_5MW 2 > +#define ACAB2_U3_CLD_1MW 3 > +#define ACAB2_U3_CLD_500UW 4 > +#define ACAB2_U3_CLD_200UW 5 > +#define ACAB2_U3_CLD_50UW 6 > + > +/* Other Active Cable VDO 2 Fields */ > +#define ACAB2_U3U0_DIRECT 0 > +#define ACAB2_U3U0_U3S 1 > +#define ACAB2_PHY_COPPER 0 > +#define ACAB2_PHY_OPTICAL 1 > +#define ACAB2_REDRIVER 0 > +#define ACAB2_RETIMER 1 > +#define ACAB2_USB4_SUPP 0 > +#define ACAB2_USB4_NOT_SUPP 1 > +#define ACAB2_USB2_SUPP 0 > +#define ACAB2_USB2_NOT_SUPP 1 > +#define ACAB2_USB32_SUPP 0 > +#define ACAB2_USB32_NOT_SUPP 1 > +#define ACAB2_LANES_ONE 0 > +#define ACAB2_LANES_TWO 1 > +#define ACAB2_OPT_ISO_NO 0 > +#define ACAB2_OPT_ISO_YES 1 > +#define ACAB2_GEN_1 0 > +#define ACAB2_GEN_2_PLUS 1 > + > +#define VDO_ACABLE2(mtemp, stemp, u3p, trans, phy, ele, u4, hops, u2, u32, lane, iso, gen) \ > + (((mtemp) & 0xff) << 24 | ((stemp) & 0xff) << 16 | ((u3p) & 0x7) << 12 \ > + | (trans) << 11 | (phy) << 10 | (ele) << 9 | (u4) << 8 \ > + | ((hops) & 0x3) << 6 | (u2) << 5 | (u32) << 4 | (lane) << 3 \ > + | (iso) << 2 | (gen)) > + > +/* > + * VPD VDO > + * --------- > + * <31:28> :: HW version > + * <27:24> :: FW version > + * <23:21> :: VDO version > + * <20:17> :: Reserved, Shall be set to zero > + * <16:15> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V) > + * <14> :: Charge through current support (0b == 3A, 1b == 5A) > + * <13> :: Reserved, Shall be set to zero > + * <12:7> :: Vbus impedance > + * <6:1> :: Ground impedance > + * <0> :: Charge through support (0b == no, 1b == yes) > + */ > +#define VPD_VDO_VER1_0 0 > +#define VPD_MAX_VBUS_20V 0 > +#define VPD_MAX_VBUS_30V 1 > +#define VPD_MAX_VBUS_40V 2 > +#define VPD_MAX_VBUS_50V 3 > +#define VPDCT_CURR_3A 0 > +#define VPDCT_CURR_5A 1 > +#define VPDCT_NOT_SUPP 0 > +#define VPDCT_SUPP 1 > + > +#define VDO_VPD(hw, fw, ver, vbm, curr, vbi, gi, ct) \ > + (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21 \ > + | ((vbm) & 0x3) << 15 | (curr) << 14 | ((vbi) & 0x3f) << 7 \ > + | ((gi) & 0x3f) << 1 | (ct)) > + > +#endif /* __DT_POWER_DELIVERY_H */ > -- > 2.30.0.365.g02bc693789-goog >
